Precise Optical Modulation

Version	Summary	Created by	Modification	Content Size	Created at	Operation
1		Tetsuya Kawanishi	+ 1478 word(s)	1478	2021-05-17 07:44:59	\|
2	format correct	Bruce Ren	-21 word(s)	1457	2021-05-19 10:05:42	\|

This entry is adapted from the peer-reviewed paper 10.3390/photonics8050160

Optoelectronic devices which play important roles in high-speed optical fiber networks can offer effective measurement methods for optoelectronic devices including optical modulators and photodetectors. Precise optical signal modulation is required for measurement applications.

optical modulation extinction ratio chirp parameter two-tone signal single sideband frequency sweep electro-optic effect optoelectronic devices

1. Introduction

For high-speed optical links, external modulators are commonly used to generate broadband optical signals. High-speed modulation whose operation bandwidth is up to 100 GHz has been reported by using optical modulators based on electro-optic effect in various materials such as lithium niobate ^[1]^[2], silicon ^[3]^[4] and indium phosphide ^[5]^[6]. Optical signals generated by optical transmitters consisting of lasers and modulators would be converted into electric signals by photodetectors at receivers. Recently, various multilevel modulation techniques have been investigated to increase transmission capacity, where high-speed and precise lightwave control is required in optical-to-electric and electric-to-optical signal conversion ^[1]. Waveform transfer is needed to construct mobile networks consisting of many base stations and remote antenna units ^[7]. Waveforms are sent from base stations to remote antenna units over optical fiber links, where waveforms for radio services are generated and processed at base stations ^[8]. In the fourth generation (4G) mobile system, digital radio-over-fiber (RoF) is commonly used for the waveform transfer, because the required bitrate for digitized waveforms is much less than 10 Gb/s. Thus, we can use low-cost digital optical fiber links for connection between base stations and remote antenna units. However, in the fifth generation (5G) mobile system, the required bitrate for such connection would be larger than a few hundred Gb/s. Analog RoF links would be useful in 5G or beyond mobile systems, to save the required bitrate or bandwidth ^[8]. Precise lightwave control is required in analog RoF systems, which would be sensitive to nonlinearity and frequency response, as well as in digital transmission systems with multilevel modulation formats.

2. Intensity Modulation by a Balanced Mach-Zehnder Modulator

An MZM consists of two optical phase modulators (PMs) connected in parallel through two Y-junctions, as shown in Figure 1. The two optical paths along the phase modulators form two arms of a Mach-Zehnder interferometer (MZI). Optical phase difference between optical signals on the two optical paths can be controlled through voltages were applied to the two optical PMs (PM and PM2). In an ideal MZM where the amplitudes of the two optical signals are balanced, the optical output intensity goes to zero when the optical phase difference is equal to

π

(180-degree).

Figure 1. MZM structure.

However, there is some imbalance between the amplitudes due to fabrication error. Thus, optical output has some residual optical power, even if the optical phase difference is equal to

π

. ER, which is the optical power ratio of the maximum to the minimum, describes the preciseness of the optical modulation. Opical modulation with low ER would induce generation of spurious components in the optical output. Imbalance between optical phase modulation also would have impact on frequency or time domain profiles of the optical output. The MZM can offer pure optical intensity modulation without any optical phase excursion, when the induced optical phase shifts at the two arms of the MZI are perfectly balanced, where the phase shifts have opposite polarities each other for push-pull operation. The imbalance between the two optical phase modulators can be described by a chirp parameter which is defined by ratio of parasitic optical phase change to amplitude change.

A balanced x-cut lithium niobate MZM offers balanced push-pull phase modulation, where the chirp parameter

α

can be less than

0.2

^[1]. A dual-electrode MZM which has a separate electrode for each PM can be used for push-pull operation, where the signal applied to one PM is an inverted replica of that applied to the other PM. Modulation efficiency difference due to fabrication error can be compensated by adjusting amplitude ratio between these two signals applied to the PMs. Thus, the dual-electrode MZM can offer very small

α

at a particular frequnecy ^[9]. However, for broadband operation, it would be rather difficult to maintain the balanced operation due to frequency response difference between the two electric circuits for the two electrodes, where the electric circuits to drive the dual-electrode MZM would be more complicated than that of the x-cut single-drive MZM which has only one electrode.

3. Active Trimming for High Extinction-Ratio Intensity Modulation

An MZM with a minimum transmission bias point can generate an optical two-tone signal consisting of the first order USB and LSB, which is useful for measurement applications. Spurious suppression ratio largely depends on the ER. Thus, firstly, we consider enhanement of the ER by active trimming, while the chirp parameter and ER should be adjusted simultaneously, to generate a pure optical two-tone signal.

An integrated x-cut

{LiNbO}_{3}

(LN) modulator with active trimmers can offer high ER intensity modulation ^[10]. As shown in Figure 2, the modulator has a pair of sub MZIs in a main MZI. The sub MZIs compensate imbalance in the main MZI due to fabrication error. The integrated LN modulator has three electrodes (A, B and C). The amplitude balance between the two arms in the main MZI, can be controlled by changing dc-bias voltages fed to the electrodes A and B. A modulation signal on the electrode C controls the optical phase difference between the two arms of the main MZI.

Figure 2. Integrated MZM with two active trimmers.

Figure 3 shows time-domain responses of the modulator, where the ERs with and without compensation were, respectively, 71 dB and 32 dB. Zero span operation of an optical spectrum analyzer was used to measure high extinction ratio on-off-keying. The rise and fall times of the time-domain profiles shown in Figure 3 were dominated by the response of the optical spectrum analyzer. Due to fabrication error, optical power in one arm of the MZM should be larger than that in the other arm. The optical power in the arm whose optical loss is larger than in the other arm should be adjusted by using a sub MZI ^[1]. As shown in Figure 4, the ER can be controlled by the voltage applied to the sub MZI embedded in the arm whose optical loss is larger than the other arm. The x-axis shows the dc-bias voltage offset from the imbalance compensated condition, where the scale was normalized by

V π

of the sub MZI. The ER-tuning range was from 21 dB to 54 dB.

Figure 3. On-off-keying by an MZM with and without imbalance compensation ^[1].

Figure 4. Extinction ratio controlled by a sub-MZI ^[11].

An MZM with minimum transmission bias can offer double sideband suppressed carrier (DSB-SC) modulation, where the carrier component is suppressed by destructive interference between optical waves propagating in the two waveguides of the main MZI. By feeding a sinusoidal single-tone signal as a modulating signal, we can generate an optical two-tone signal consisting of the first order USB and LSB with suppressed carrier. The suppression ratio depends on the imbalance between the optical waves, in other words, the ER of the modulator. Figure 5 shows optical spectra of optical two-tone signals generated by an MZM with active trimmers. The ER can be higher than 60 dB. The modulating signal frequencies

f_{m}

were 10.5 GHz and 20.0 GHz. The main MZI wase set to be a minimum transmission bias condition. Carrier suppression ratios with respect to the first order USB or LSB were 47.4 dB for 10.5 GHz and 40.4 dB for 20.0 GHz, when the ER was enhanced by imbalance conpensation using the active trimmers. On the other hand the suppression ratios without compensation were less than 20 dB.

Figure 5. Spectra of optical two-tone signals with

f_{m}

= 10.5 GHz (a) and 20 GHz (b) ^[1].

Parasitic optical phase modulation due to imbalance in induced phases on the two arms in the main MZI also causes generation of undesired high order sidebands. Such imbalance can be described by a chirp parameter ^[1]. The second order sideband generation was mainly due to the parasitic optical phase modulation associated with the chirp parameter

α

, while the third order components are due to intrinsic nonlinearity of the MZMs. As described above, the chirp parameter

α

can be largely suppressed by using a dual-electrode MZM ^[9].

By using a high-speed photodetector, the optical two-tone signal can be converted into a pure single-tone electric signal as a beat signal of the two optical spectral components whose frequency separation is equal to

2 f_{m}

. Figure 6a,b show wide span (DC-50 GHz) spectra of the RF signal generated from the optical two-tone signal (

f_{m} = 20.0 GHz

). with and without the compensation technique, respectively, where resolution bandwidth was 43 kHz. By using active trimming, the spurious suppression ratio could be larger than 60 dB without using any electrical or optical filters for suppression of undesired components, where the suppression ratio without using active trimming was 21.0 dB. The linewidth of the generated millimeter-wave signal was almost equal to that of the modulating signal.

Figure 6. Spectra of RF signals generated from optical two-tone signals with compensation (a) and without compensation (b) ^[1].

References

Kawanishi, T.; Sakamoto, T.; Izutsu, M. High-Speed Control of Lightwave Amplitude, Phase, and Frequency by Use of Electrooptic Effect. IEEE J. Sel. Top. Quantum Electron. 2007, 13, 79–91.
Yamaguchi, Y.; Kanno, A.; Kawanishi, T.; Izutsu, M.; Nakajima, H. Precise Optical Modulation Using Extinction-Ratio and Chirp Tunable Single-Drive Mach?Zehnder Modulator. J. Light. Technol. 2017, 35, 4781–4788.
Zhang, F.; Zhang, L.; Ruan, X.; Yang, F.; Ming, H.; Li, Y. High Baud Rate Transmission With Silicon Photonic Modulators. IEEE J. Sel. Top. Quantum Electron. 2021, 27, 1–9.
Lu, G.-W.; Zhang, H.-B.; Shinada, S.; Hong, J.; Cheng, Y.; Yokoyama, S. Power-Efficient O-Band 40 Gbit/s PAM4 Transmitter Based on Dual-Drive Cascaded Carrier-Depletion and Carrier-Injection Silicon Mach-Zehnder Modulator With Binary Driving Electronics at CMOS Voltages. IEEE J. Sel. Top. Quantum Electron. 2021, 27, 1–8.
Ogiso, Y.; Ozaki, J.; Ueda, Y.; Wakita, H.; Nagatani, M.; Yamazaki, H.; Nakamura, M.; Kobayashi, T.; Kanazawa, S.; Hashizume, Y.; et al. 80-GHz Bandwidth and 1.5-V Vπ InP-Based IQ Modulator. J. Light. Technol. 2020, 38, 249–255.
Irmscher, S.; Lewen, R.; Eriksson, U. InP-InGaAsP high-speed traveling-wave electroabsorption modulators with integrated termination resistors. IEEE Photonics Technol. Lett. 2002, 14, 923–925.
Kawanishi, T.; Kanno, A.; Freire, H.S.C. Wired and Wireless Links to Bridge Networks: Seamlessly Connecting Radio and Optical Technologies for 5G Networks. IEEE Microw. Mag. 2018, 19, 102–111.
Kawanishi, T. Wired and Wireless Seamless Access Systems for Public Infrastructure; Artech House: Norwood, MA, USA, 2020.
Kawanishi, T.; Sakamoto, T.; Chiba, A.; Tsuchiya, M.; Toda, H. Ultra high extinction-ratio and ultra low chirp optical intensity modulation for pure two-tone lightwave signal generation. In Proceedings of the 2008 Conference on Lasers and Electro-Optics and 2008 Conference on Quantum Electronics and Laser Science, San Jose, CA, USA, 4–9 May 2008; pp. 1–2.
Kawanishi, T.; Sakamoto, T.; Tsuchiya, M.; Izutsu, M. High extinction ratio optical modulator using active intensity trimmers. In Proceedings of the 2005 31st European Conference on Optical Communication, ECOC 2005, Glasgow, UK, 25–29 September 2005; Volume 4, pp. 841–842.
Kawanishi, T.; Sakamoto, T.; Chiba, A.; Izutsu, M.; Winzer, P.J. Duobinary signal generation using high-extinction ratio modulation. In Proceedings of the OFC/NFOEC 2008-2008 Conference on Optical Fiber Communication/National Fiber Optic Engineers Conference, San Diego, CA, USA, 24–28 February 2008; pp. 1–3.

© Text is available under the terms and conditions of the Creative Commons Attribution (CC BY) license; additional terms may apply. By using this site, you agree to the Terms and Conditions and Privacy Policy.

Upload a video for this entry

Information

Subjects: Optics

Contributor MDPI registered users' name will be linked to their SciProfiles pages. To register with us, please refer to https://encyclopedia.pub/register :

Tetsuya Kawanishi

View Times: 648

Update Date: 19 May 2021

Table of Contents

Video Upload Options

Confirm

1. Introduction

2. Intensity Modulation by a Balanced Mach-Zehnder Modulator

3. Active Trimming for High Extinction-Ratio Intensity Modulation

References