Submitted Successfully!
To reward your contribution, here is a gift for you: A free trial for our video production service.
Thank you for your contribution! You can also upload a video entry or images related to this topic.
Version Summary Created by Modification Content Size Created at Operation
1
Xiaohui Lei
 -- 4353 2023-11-15 06:16:19 |
2 references update
Fanny Huang
 Meta information modification 4353 2023-11-15 08:05:51 | |
3 layout
Fanny Huang
 -1 word(s) 4352 2023-11-21 06:55:12 |

Video Upload Options

Do you have a full video?
Send video materials Upload full video

Confirm

Are you sure to Delete?
Yes No
Cite
If you have any further questions, please contact Encyclopedia Editorial Office.
Lei, X.; Yuan, Q.; Xyu, T.; Qi, Y.; Zeng, J.; Huang, K.; Sun, Y.; Herbst, A.; Lyu, X. Mechanized Blossom Thinning in Orchards. Encyclopedia. Available online: https://encyclopedia.pub/entry/51579 (accessed on 29 April 2024).
Lei X, Yuan Q, Xyu T, Qi Y, Zeng J, Huang K, et al. Mechanized Blossom Thinning in Orchards. Encyclopedia. Available at: https://encyclopedia.pub/entry/51579. Accessed April 29, 2024.
Lei, Xiaohui, Quanchun Yuan, Tao Xyu, Yannan Qi, Jin Zeng, Kai Huang, Yuanhao Sun, Andreas Herbst, Xiaolan Lyu. "Mechanized Blossom Thinning in Orchards" Encyclopedia, https://encyclopedia.pub/entry/51579 (accessed April 29, 2024).
Lei, X., Yuan, Q., Xyu, T., Qi, Y., Zeng, J., Huang, K., Sun, Y., Herbst, A., & Lyu, X. (2023, November 15). Mechanized Blossom Thinning in Orchards. In Encyclopedia. https://encyclopedia.pub/entry/51579
Lei, Xiaohui, et al. "Mechanized Blossom Thinning in Orchards." Encyclopedia. Web. 15 November, 2023.
Mechanized Blossom Thinning in Orchards
Edit
This entry is adapted from the peer-reviewed paper 10.3390/agronomy13112753

Orchard thinning can avoid biennial bearing and improve fruit quality, which is a necessary agronomic section in orchard management. The existing methods of artificial fruit thinning and chemical spraying are no longer suitable for the development of modern agriculture. With the continuous acceleration of the construction process of modern orchards, blossom thinning mechanization has become an inevitable trend in the development of the orchard flower and fruit management.

orchard thinning mechanism

1. Introduction

China has an orchard area of over 12 million hectares and a total output of nearly 300 million tons, making it the largest fruit producer and consumer in the world [1][2][3]. With the continuous expansion of the orchard planting area and the increasing requirements for large-scale management, the importance of mechanized orchards is becoming increasingly prominent. However, the research on related technologies started late and had a poor foundation, resulting in an orchard comprehensive mechanization rate of less than 30% [4][5]. Especially in some agronomic sections with a high labor demand, high labor intensity, and tight agricultural seasons, mechanization has not been achieved. Moreover, China is facing an aging population of orchard farmers [6]. The lack of efficient and labor-saving agricultural equipment has become a bottleneck that restricts the development of the fruit industry.
Thinning can avoid biennial bearing and improve fruit quality, which is a necessary agronomic section in pear orchard management [7][8]. The existing methods of artificial fruit thinning and chemical spraying are no longer suitable for the development of modern agriculture. Artificial fruit thinning consumes labor and time, wastes tree nutrients, and has a high-risk factor for tree-top operations [9]. The application of chemical thinning pollutes the environment, and the agents are easily affected by factors such as the spraying time, preparation concentration, and working site environment [10][11][12]. As a result, they are rarely used in actual field operations. Orchard thinning, as a key step in increasing orchard yields, still relies on manual operations. Manual operation is time-consuming and inefficient, and the experience requirements for agricultural operators in blossom thinning work are still high. With the continuous acceleration of the construction process of modern orchards, blossom thinning mechanization has become an inevitable trend in the development of orchard flower and fruit management.
Based on relevant reports in the past 20 years, the current level of development of mechanized blossom thinning technologies and equipment in orchards from three aspects: mechanism research, machine development, and intelligent upgrading are discussed. Combining the advantages and disadvantages of the research, the authors propose thoughts and prospects on orchard mechanized blossom thinning.

2. Mechanism Research

2.1. Thinning Force

The process of striking is complicated, which is the dynamic impact, friction, and vibration behavior of a flexible rope interacting with branches, inflorescences, and young fruits of fruit trees. It is difficult to estimate the impact force of the thinning rope on branches and inflorescence, and the damage degree of non-target parts such as branches and leaf buds is also difficult to estimate. Scholars have carried out relevant research on the flexible impact mechanism.
Hu et al. used a universal materials tester to measure the tensile and shear forces of apple branches’ pedicel node and receptacles corolla node [13]. After repeated tests, the results showed that the average maximum tensile and shear force of the branches pedicel node in full bloom period were 3.5 N and 2.82 N, respectively. The average maximum tensile force that the receptacles corolla nodes can bear is 1.6 N. Combined with the ADAMS multi-body dynamics simulation, Hu’s team also designed a performance test bench for the end actuator of the thinner. They tested the impact force of three kinds of thinning ropes made of a solid rubber strip, hollow vinyl strip, and nylon braid under different lengths, wire diameters, and speeds of the thinning shaft [14][15][16][17][18]. The optimal parameters of the actuator are as follows: the material of the thinning rope is solid rubber, the length is 20 cm, the linear diameter is 5 mm, the rotational speed of the spindle is 960 r/min, and the impact force of the thinning rope on the test branch is 5.39 N. Starting from the mechanical characteristics of peach branches, Yuan et al. obtained the stress curve of the branches and the shear strength of the branches is 6 MPa. Meanwhile, they established a rigid–flexible coupling multi-body dynamics model for the striking force of branches, analyzed the striking force of the thinning rope on branches at different rotational speeds, and concluded that the striking force range of the thinning rope is 3.3–7.6 N when the rotating speed of the spindle is 240–480 r/min [19][20][21]. Assirelli A. et al. studied the thinning power of young peach fruit, when the fruits were 20–40 mm in size and different angles were evaluated to simulate the various ways in which the thinner hits the fruits [22]. The analysis of the different angles showed that, on average, the fruits are detached more easily if the force is applied with a 90° angle, respective to the fruit position on the branch. On the other hand, if the force is applied with an angle of 0°, the average force required is three times higher.

2.2. Thinning Agronomy

The research of the thinning mechanism should not only solve the problem of flexible hitting, but should also solve the problem of thinning agronomy. Due to the different species of fruit trees, the number of flower buds contained in their inflorescence is different, and their agronomic requirements for thinning are also different. The apple, pear, and grape belong to a mixed inflorescence and there are multiple flower buds on one inflorescence, while the peach and nectarine belong to a single inflorescence and there is only one flower bud on one inflorescence. Is the effect of thinning better in the bud stage or in the full bloom stage? Is removing the side flower better than the center flower when thinning the apple tree? What is the appropriate setting for the proportion of inflorescence thinning? Relevant scholars have conducted research on such thinning agronomic issues.
Sidhu et al. compared artificial bud extinction and blossom thinning in the ‘Scilate’ Apple; the results demonstrated that artificial bud extinction consistently outperformed blossom thinning in terms of an improved fruit set, return bloom, and fruit weight. The fruit quality parameters, such as flesh firmness, total soluble solids, dry matter content, malic acid content, and fruit shape, were also improved under the artificial bud extinction regime [23]. Oliveira et al. evaluate the effect of shoot heading and of thinning in different development stages of flowers and fruits on the fruit production and quality of the ‘BRS Kampai’ peach. The results showed that thinning during flowering and at the beginning of fruit growth increases the fruit size, and that shoot heading reduces plant production, but does not significantly increase the fruit size [24]. Szot et al. evaluate the effect of the crop load, thinning practices, and position in the tree crown on the quantity and quality of the ‘Szampion’ apple [25]. The thinning treatments were performed at the pink bud stage and full bloom stage, leaving only the king flower or lateral flower. The best results in terms of the regularity of yielding and high-quality fruits after thinning at the pink bud stage to the king flower were obtained. Han et al. studied the effects of berry thinning on bunch compactness, grape sugar accumulation, and subsequent wine quality in the Vitis vinifera L. Cabernet Sauvignon [26]. Based on the decreasing proportion of berries in one bunch, the treatment was designated as a 25% decrease and a 50% decrease. The results showed that the different berry thinning treatment lowered bunch compactness accordingly; the content of sugar, anthocyanins, total phenols, and the mass of mature berries were all significantly enhanced with a decreasing compactness at the same harvested time. Nie et al. studied the effects of blossom thinning on the fruit setting rate and fruit quality of apple inflorescences at different periods [27]. The test results showed that the thinning technique had a better fruit setting rate of apple inflorescences, fruit weight per fruit, color index, finish index, and soluble solid content than the traditional technique. Hua et al. took the Tainong No. 1 mango tree, aged 6 to 8 years, as the test material to study the optimal date of blossom thinning of the mango. The test results showed that the blossom thinning effect was better at the early bloom stage [28].

2.3. Thinning Model

In order to study the relationship between thinning and fruit yield, relevant scholars established the fruit tree growth model and theory. Iwanami et al. developed a theoretical model using the ‘Fuji’ apple to explain the relationships among the timing of thinning, crop load, fruit weight, and bloom return [29]. The rate of flower-bud formation in the current year could be explained by a regression model of the timing of the thinning, crop load, and rate of flower-bud formation in the previous year. The fruit weight in the current year could be explained by a regression model of the timing of the thinning, crop load, rate of flower-bud formation, and shoot length in the current year and the previous year. Pellerin et al. proposes that thinning is a partial transfer of potential flower buds from one year to the next year and estimates the maximum repeatable sequence of flower buds without biennial bearing [30]. Manfrini et al. investigate the feasibility of a spatial analysis in apple orchards to assist growers with decision making [31]. A variation in the spatial distribution of the fruit load prior to the thinning was observed, indicating a possibility to spatially and differentially manage the orchard. No spatial variation in the fruit number was observed prior to the harvest, indicating that thinning had removed the previously-observed spatial variation in the crop load. Reginato et al. assessed the relationship between crop load and fruit size or crop load and yield efficiency by a regression analysis for nectarines and cling peaches [32]. With this methodology, the predicted crop value can be established for different growing conditions leading to an improved crop load management. This will permit growers to optimize the net return that can be obtained for a specific orchard. Understanding how crop value is affected by crop load for different cultivars can lead to better decisions in the design and establishment of new orchards.

3. Machine Development

3.1. Hand-Held Thinner

The hand-held thinner belongs to the semi-mechanized orchard management equipment, which is mainly composed of an energy supply device, operating lever, and thinning action actuator. According to the operating principle of the thinning action actuator, it can be divided into three kinds: an impact type, finger brush type, and vibration type. During the operation, the operator holds the operation lever and thins the target’s inflorescences, or vibrates the canopy branches according to the agronomic requirements of the fruit tree to reduce the blossoms and fruits. The operator determines the percentage of inflorescences and young fruits that need to be removed by subjectively judging. Because of the small structure and portability, operators can directly carry the work in hand. The hand-held thinner is mainly suitable for traditional old orchards with a messy canopy structure, especially in the interior and top of the canopy.
The string type thinner is widely used, and there are many marketable products. It is controlled by a DC motor to control the speed of the spindle, so as to control the hitting force of the rope on the target inflorescence. The electric hand-held blossom thinner made by Infaco Co. Ltd. (Cahuzac sur Vère, France) has a rotary head with a five-finger comb and is powered by a 48 V electric motor; it was equipped with a portable battery bag which facilitated worker mobility in the field [33]. The orchard blossom thinner made by Cinch Co. Ltd. (Shelby Township, MI, USA) has two types of electric and manual for customers to choose; the installation hole on the spindle is reserved for the rope and is used to adjust the density of the rope according to the flower intensity. It is used on peach, cherry, apple, plum, apricot, and nectarine varietals [34]. The AF 100 electronic blossom/young fruit thinner made by Lakewoodproducts Co. Ltd. (Wellington, New Zealand) is particularly effective with stone fruit, such as nectarines, apricots, peaches, and plums. Its loop is made from high strength flexible rubber fitted on a shaft and the rubber loops will adapt to the location to remove the blossom without damaging the leaves or bark [35]. For the electric finger blossom/young fruit thinner, the rotation of the finger dial was controlled by the motor, and the target blossom/young fruit falls off in the friction and impact action with the finger brush. The Giulivo-plus electric finger thinner, made by Volpi Co. Ltd. (Casalromano, Italy), had a head with six rotating fingers and was powered by a 12 V electric motor; electricity was supplied by a 12 V, 75 Ah car battery, which remained on the ground, and a 15 m long electric extension cord [36]. For the shaking thinning device, the vibration was formed by the CAM mechanism action, acting on the branches of fruit trees, which is used for picking and thinning small fruit by acting on the branches of fruit trees. The hand-held shaker made by Campagnola Co. Ltd. in Italy is an air compressor which provided pressure between 1.0 and 1.2 MPa. The mobility of this device was limited due, in part, to the presence of the flexible hose that fed the compressed air to the shaker [37]. 
Relevant scientific research institutions have also designed their own hand-held thinners. Most of them are improved designs of market products and exist in the form of patents. Fruit varieties include citrus, apple, pear, peach, grape, kiwi, grape, etc. The example patent of the hand-held thinner is shown in Table 2 [38][39][40][41][42][43][44][45][46][47]. Researchers also carried out field tests on the performance of the hand-held thinners. Lei et al. developed a hand-held electric rotating rope blossom thinner for the ‘Cuiguan’ pear orchard: its spindle speed is from 0–900 r/min and extension rod length range is from 0.95 to 1.6 m. Compared with the hand thinning, the thinner can shorten the thinning time of the small canopy layer orchard by 30.71% and the Y-trellis orchard by 48.68%, respectively [48][49]. Wang et al. developed a hand-held mechanical thinning device suitable for the apple, stone fruits, and sweet cherry, with its spindle speed from 500 to 3000 r/min. Field test results indicated that the test device could remove 61.1%, 30.8%, and 18.0% of flowers on a single branch with a swipe of around 0.5 m/s under high, medium, and low speed settings, respectively [50][51]. Martin et al. tested the Giulivo-plus electric finger thinner and the Campagnola hand-held shaker on a peach tree. The results indicated that the finger thinner reduced the time by 46% and the shaker reduced the time by 28%; two thinners reduced the crop load by 38% and increased the mass of the fruit by 47% at harvest compared to non-thinned trees [52]. After that, Martin et al. developed a hand-held fruit thinner prototype: it had a rotating cylinder with 10 flexible cords, placed at the top of a pole 2 m in length. They carried out a field test with the Infaco and Giulivo-plus thinner in peach orchards; there is no differences among them in terms of thinning time and the number of fruits per cm2 of the trunk cross-sectional area at harvesting. Hand thinning took 385 h/ha, and mechanical thinning reduced this time by 89%. The cost of hand thinning was 4.8 €/tree, whereas the cost of mechanical thinning ranged from 0.4 to 1.1 €/tree [53][54]. Spornberger et al. tested the portable thinner and manual thinning in organically managed cherry orchards at the stage of a pea size; the portable thinner showed a high thinning effect, and because of lower costs, it is more suitable for farmers than the hand thinning of flowers or fruits [55].

3.2. Tractor-Mounted Thinner

The tractor-mounted thinner belongs to the mechanized blossom and fruit management equipment. The whole machine is operated by the tractor and the rotating power of the spindle is provided by the tractor hydraulic mechanism. The marketable productions are divided into three kinds according to the structure of the thinning arm: the single spindle, multiple spindles, and horizontal rotary spindle. The working mechanism between the thinning rope and the inflorescence is that of the hitting, rubbing, and vibrating. According to the fruit species, crown type, and other agronomic parameters, operators adjust the tractor advancing speed, the spindle operation angle, the spindle rotational speed, and the density of the thinning rope, so as to reasonably select the thinning intensity. The tractor-mounted thinner is mainly suitable for orchards with the same crown structure, such as the hedge type, trunk type, and V-type.
At present, the Darwin series orchard single spindle string blossom thinner made by Fruit Tec Co., Ltd. is the mainstream one in the market. The Darwin S is mounted on the front of the tractor, so a better view of the spindle is ensured and thus, the operator can guide the spindle more easily on the tree canopy. The spindle rotational speed can be comfortably and continuously adjusted with buttons on the control unit in the driver’s cabin to be optimally adapted to the driving speed. The Darwin PT is attached to a front loader directly and is designed to work mainly in the V-type canopy tree. The spindle has a tilt angle of 180°; this allows it to be lifted to the height of the tree-tops and work horizontally over the trees. If the vase trees are very wide, there is also the possibility of tilting the spindle into the tree’s interior. The Darwin SmaArt replaces the subjective estimation of the blooming strength with the eye with objective detection by camera. To do this, a camera in front of the thinning spindle detects the blossom density of each individual tree and passes on the data to the on-board computer in real time. Using a thinning algorithm, the computer then calculates the optimum spindle speed and controls the thinning unit. As an option, the system can be combined with a GPS receiver. Using the GPS system, it is possible to detect each individual tree and to assign the data, such as the number of blossoms and the spindle speed, to the tree and to compare it later with the yield data.
In recent years, scholars have carried out a large number of tests in apple, peach, and plum orchards with the Darwin series thinner. The range of the optimal working speed is 6 to 18 km/h, and the range of the spindle rotation speed is 150 to 450 r/min. Accurate working parameters need to be obtained in the field according to the fruit tree species, the shape of the canopy, and the period of blossom thinning. Wallis et al. evaluated the risk of fire blight development and spread after Darwin 300 blossom thinning in apple orchards. The results demonstrate that the use of the thinner should, therefore, be limited to orchards with no history of disease in the last 3 years and on days when predicted weather is not suitable for tree infection; there is a low risk for fire blight development and spread by mechanical thinning under an early blossom stage, especially when paired with a subsequent bactericide application [56][57]. Penzel et al. translated the Darwin 250 spindle rotational frequency to average kinetic energy. At a high flower set, thinning treatments of 0.23 J and 0.33 J were adequate settings to reduce crop load in ‘Elstar’ and 0.33 J in ‘Gala’ without yield loss [58]. Lordan et al. evaluated the working performance of Darwin 250 in ‘Gala’, ‘Golden Delicious’, and ‘Fuji’ apple orchards; two prediction models were developed to adjust the right tractor and spindle rotational speeds depending on the initial number of flower clusters [59]. Theron et al. evaluated chemical thinning with the Darwin thinner during the plum blossom stage; the method increased the fruit drop, fruit size, and fruit weight [60]. Cline et al. tested the Darwin 300 and hand thinning in apple and peach orchards; the result showed that mechanical thinning represents a viable method for initial crop load reduction, coupled with hand thinning after fruit, set to reach a final optimal production [61][62]. Baugher et al. tested the Darwin 300 in V-shaped and open-center trained peach orchards; they demonstrated that the mechanical thinner reduces labor requirements and improves fruit size [63][64][65][66][67].
Other companies also make related productions, such as the Eclairvale series orchard thinner made by La Canne Vale Co., Ltd. (Narbonne, France) [68]. The machine can be adopted to be both semi-mounted and mounted, to perform the thinning operation adequately: the total mass of the tractor with or without front ballast must guarantee the stability of a 3 m rear overhang. It has a freely rotating rotor onto which semi-rigid rods are attached. Its rotation occurs through the penetration of the rods into the canopy and the advancement of the tractor, which induces a slow rotation and rubbing of the rods against the branches, which causes some of the blossom or green fruit to fall. Rods are made of flexible glass fibers with a soft plastic end cap; it is the only wearing part and each rod can be easily replaced in less than one minute. Assirelli et al. tested the Eclairvale thinner in apricot and peach orchards [69][70][71]. In the apricot, the machine removed 20.8% of flowers and 43.6% of fruit, allowing 48% time-saving in the follow-up fruit manual thinning as compared with the hand thinning. In the peach, mechanical thinning at blooming time removed 63% of flowers, allowing 42.4% time-saving in the follow-up fruit manual thinning as compared with the hand thinning. Fruit damages always remained below the economic thresholds to marketable production or to the plant.
The FLEXITREE three-arm blossom thinner made by Clemens Co. Ltd. (Wittlich, Germany), which is linked in front of a tractor [72]. Three arms are installed flexibly in different positions of the vertical rod and its structure can be changed by adjusting, which has the advantage of more penetration into the canopy. The device is flexibly configurable and can be perfectly adapted to the crown structure and different tree heights by means of various adjustment options. Lei et al. designed a three-arm tractor-mounted flower thinner named TTBT-300 for ‘Y’ trellis and trunk-type pear orchards; the field test showed that the thinner can save at least 60% of artificial fruit thinning time and the profitable area was 0.58 hm2 [73][74]. Blanke et al. designed a three-arm tractor-mounted flower thinner named Bonner for plums and apples. In the plum orchard, the yield of Class one fruits increased per tree from 47% in the un-thinned controls up to 69%; the fruit mass was enlarged from 28 g in the un-thinned control to 30–32 g [75][76]. In the apple orchard, the portion of Class one fruits bigger than 70 mm was increased by 10% without yield loss and it reduced the subsequent hand thinning by, respectively, 32.5% [77][78]. They also proposed an integrated coefficient of thinning (ICT) to develop the critical parameters of the machine. The optimum values are 10–40, where an ICT > 50 led to tree damage and ICT < 8 led to sub-optimum thinning efficacy [79][80].
The spiked-drum shaker made by the United States Department of Agriculture consisted of several panels of radially spaced nylon rods bolted to plates on a central spindle. Schupp et al. evaluated the double spiked-drum shaker on the peach; it reduced peach crop load by an average of 36%, decreased follow-up hand thinning time by 20% to 42%, and increased fruit in higher market value size categories by 35% [81]. Miller et al. evaluated the single and double spiked-drum shaker on the peach to reduce the cost and time required for hand thinning peaches. At the 60% full blossom stage, the double-spiked drum shaker reduced crop load by 27% and the single spiked-drum shaker reduced crop load by 9%; they removed an average of 37% of the green fruit [82].
The one-rotor orchard horizontal rotary thinner made by Phil Brown Welding Co. Ltd. can be carried on a standard forklift tractor [83]. The rotor was driven by a hydraulic with a variable speed, and the ropes can be easily replaced when worn. Aasted et al. developed a system using an LIDAR to sense the canopy and automatically control the position of a modified Darwin string thinner position to maintain engagement [84]. They found that the laser control system performed similarly to the joystick control for the blossom counts. Though the laser system was slightly less engaged on the lower canopy, the overall scaffold performance was much closer. Lyons et al. developed a visual blossom thinning system [85]. It consisted of kinematic targeting and heuristic programming, a robotic arm, and a pomologically designed end-effector. The robotic arm had a consistent range of −1.26 cm to +1.57 cm vector magnitude per target location, and the end-effector brushes had a consistent range of −2.97 cm to +3.04 cm per target location. Li et al. developed a profiling control system for the litchi blossom thinner; the spatial position of the spindle could be adjusted by the translational screw and profile adjusting screw. The test results show that the dynamic mean errors of the translational screw and profile adjusting screw were 0.17 and 0.07 cm, respectively; the actuators have good position-adjusting accuracy and the proposed profiling control system can meet the requirements of real-time control [86][87]. Wouters et al. established a set of multi-spectral camera systems for the detection of pear inflorescence, which can identify pear inflorescence in six bands of visible and near infrared spectra [88]. The test results show that approximately 87% of the visible floral buds were detected correctly with a low false discovery rate (<16%).
There are mainly four kinds: the single spindle string thinner has an angle adjusting device, multi-arm profiling thinner, multi-sensors automatic thinner, and machine vision intelligent thinner. The blossom thinner angle adjusting device is designed for the single spindle string thinner, aiming at adjusting the spindle angle to adapt to different tree canopies. The multi-arm profiling thinner is a pure mechanism innovation model, which realizes fruit tree canopy profiling through mechanism deformation. The multi-sensors automatic thinner adds sensors such as the radar, infrared probe, and ultrasonic probe to the existing blossom thinning equipment to realize the operation of the spindle angle and rotation speed adjusting. The machine vision intelligent thinner is a kind of intelligent blossom thinning equipment, which replaces human eyes with a high-definition camera, replaces the human brain with a deep learning convolutional neural network, and replaces the human hand with a mechanical flower thinning arm. At present, most of the patented products are a conceptual design, which has a certain theoretical basis. Some prototypes have been successfully developed, but there is still a certain distance to commercialization.

References

  1. National Bureau of Statistics of the People’s Republic of China. Chinese Statistical Yearbook; China Statistics Press: Beijing, China, 2023; 935p.
  2. Zheng, Y.J.; Chen, B.T.; Lyu, H.T.; Kang, F.; Jiang, S.J. Research progress of orchard plant protection mechanization technology and equipment in China. J. Trans. Chin. Soc. Agric. Eng. 2020, 36, 110–124.
  3. Zheng, Y.J.; Jiang, S.J.; Chen, B.T.; Lyu, H.T.; Wang, C.; Kang, F. Review on technology and equipment of mechanization in hilly orchard. J. Trans. Chin. Soc. Agric. Mech. 2020, 51, 1–20.
  4. Wang, W.H.; Wang, G.P.; Tian, L.M.; Li, X.G.; Lyu, X.L.; Zhang, Y.X.; Zhang, J.H.; Cao, Y.F. Fruit scientific research in new China in the past 70 years: Pear. J. Fruit Sci. 2019, 36, 1273–1282.
  5. Zhao, Y.; Xiao, H.R.; Mei, S.; Song, Z.Y.; Ding, W.Q.; Jin, Y.; Han, Y.; Xia, X.F.; Yang, G. Current status and development strategies of orchard mechanization production in China. J. Chin. Agric. Univ. 2017, 22, 116–127.
  6. Qiao, Z.X. Impact of Agricultural Labor Aging on Production Behavior of Apple Households: A Case Study from Shanxi and Gansu Province; Northwest A&F University: Xianyang, China, 2018; 202p.
  7. Rivero, R.; Sonsteby, A.; Heide, O.M.; Mage, F.; Remberg, S.F. Flowering phenology and the interrelations between phenological stages in apple trees (Malus domestica Borkh.) as influenced by the Nordic climate. Acta Agric. Svandinavica Section B-Soil Plant Sci. 2017, 67, 292–302.
  8. Pavanello, A.P.; Zoth, M.; Ayub, R.A. Manage of crop load to improve fruit quality in plums. Rev. Bras. Frutic. 2018, 40, 721.
  9. Barreto, C.F.; Antunes, L.E.; Ferreira, L.V.; Navroski, R.; Benati, J.A.; Pereira, J.F. Mechanical flower thinning in peach trees. Rev. Bras. Frutic. 2019, 41, 465.
  10. Robinson, T.L.; Lakso, A.N. Predicting chemical thinner response with a carbohydrate model. Acta Horticul. 2011, 903, 743–750.
  11. Miller, S.S.; Tworkoski, T. Blossom thinning in apple and peach with an essential oil. HortScience 2010, 45, 1218–1225.
  12. Hampson, C.; Bedford, K. Efficacy of blossom thinning treatments to reduce fruit set and increase fruit size of ambrosia and aurora golden gala (TM) apples. Can. J. Plant Sci. 2011, 91, 983–990.
  13. Hu, C.Q.; Sun, C.H.; Xu, Y. Experiment and analysis of mechanical properties for branches pedicel node and receptacles corolla node of apple tree. J. Qingdao Agric. Univ. 2015, 32, 211–214.
  14. Sun, C.H.; Hu, C.Q.; Hou, Q.S.; Pan, Z.G. Simulation of mechanical thinning flower actuator based on ADAMS. J. Agric. Mech. Res. 2015, 37, 70–73.
  15. Hu, C.Q.; Sun, C.H.; Ji, J. Performance experiment and analysis on mechanical thinning flower actuator. J. Chin. Agric. Mech. 2015, 36, 24–28.
  16. Hu, C.Q.; Sui, R.D. Fruit Tree Mechanical Blossom Thinning Machine Performance Test Bench. P. China CN103454077B, 4 May 2016.
  17. Hu, C.Q.; Sui, R.D. Hydraulic Fruit Tree Blossom Thinning Machine and Method Based on Machine Vision. P. China CN103081730B, 10 September 2014.
  18. Hu, C.Q.; Sui, R.D. Hydraulic transmission type fruit tree flower thinning machine based on machine vision and flower thinning method. P. China CN203120538U, 14 August 2013.
  19. Yuan, C.W.D. Design and Performance Test of Peach Blossom Thinning Machine; Hebei Agricultural University: Baoding, China, 2020; 64p.
  20. Wang, Q.D. Design and Research of Mechanical Blossom Thinning Device for the Dwarf Dense Fruit Trees; Hebei Agricultural University: Baoding, China, 2018; 71p.
  21. Yang, X.; Wang, P.F.; Li, J.P.; Liu, H.J.; Shao, J.Z.; Qian, J. Wide Row Close Planting Fruit Tree Blossom Thinning Machine. P. China CN210381974U, 24 April 2020.
  22. Assirelli, A.; Caracciolo, G.; Cacchi, M.; Sirri, S.; Pallottino, F.; Costa, C. Evaluation of the detachment force needed for mechanical thinning of green peach fruits. Sustainability 2018, 10, 2291.
  23. Sidhu, R.S.; Bound, S.A.; Hunt, I. Crop load and thinning methods impact yield, nutrient content, fruit quality, and physiological disorders in ‘Scilate’ apples. Agronomy 2022, 12, 1989.
  24. De Oliveira, P.D.; Bettio Marodin, G.A.; De Almeida, G.K.; Gonzatto, M.P.; Darde, D.C. Heading of shoots and hand thinning of flowers and fruits on ‘BRS Kampai’ peach trees. Pesqui. Agropecu. Bras. 2017, 52, 1006–1016.
  25. Szot, I.; Lipa, T. Apple trees yielding and fruit quality depending on the crop load, branch type and position in the crown. Acta Sci. Pol. Hortoru. 2019, 18, 205–215.
  26. Han, W.W.; Han, N.; He, X.; Zhao, X.J. Berry thinning to reduce bunch compactness improves fruit quality of Cabernet Sauvignon (Vitis vinifera L.). Sci. Hortic. 2019, 246, 589–596.
  27. Nie, P.X.; Lu, C.; Xue, X.M.; Wang, G.P.; Wang, J.Z. Effects of apple inflorescence thinning at different periods on fruit set rate and fruit quality. J. Hebei Agric. Sci. 2013, 17, 27–29.
  28. Hua, M.; Deng, H.D.; Guo, L.J.; Feng, X.J.; Chen, L.M. Effects of mechanical flowerthinning and chemical fruit thinning on average seedless fruit weight and quality of ‘Tainong No.1′ mango. Chin. Tropic. Agric. 2021, 4, 42–46+80.
  29. Iwanami, H.; Moriya-Tanaka, Y.; Honda, C.; Hanada, T.; Wada, M. A model for representing the relationships among crop load, timing of thinning, flower bud formation, and fruit weight in apples. Sci. Hortic. 2018, 242, 181–187.
  30. Pellerin, B.P.; Buszard, D.; Iron, D.; Embree, C.G.; Marini, R.P.; Nichols, D.S.; Neilsen, G.H.; Nelsen, D. A theory of blossom thinning to consider maximum annual flower bud numbers on biennial apple trees. Hortscience 2011, 46, 40–42.
  31. Manfrini, L.; Taylor, J.A.; Grappadelli, L.C. Spatial analysis of the effect of fruit thinning on apple crop load. Eur. J. Hortic. Sci. 2009, 74, 54–60.
  32. Reginato, G.H.; De Cortazar, V.G.; Robinson, T.L. Predicted crop value for nectarines and cling peaches of different harvest season as a function of crop load. Hortscience 2007, 42, 239–245.
  33. Infaco. Available online: https://www.infaco.com/fr/produits/eclaircisseuse-ec1700-powercoup-pw3/ (accessed on 22 April 2023).
  34. Cinch. Available online: https://blossomcinch.com/ (accessed on 22 April 2023).
  35. Lakewoodproducts. Available online: https://www.lakewoodproducts.co.nz/horticulture/electronic-blossom-thinners/ (accessed on 22 April 2023).
  36. Volpi. Available online: https://www.volpioriginale.it/en/product/giulivo-plus/ (accessed on 22 April 2023).
  37. Campagnola. Available online: https://www.campagnola.co.uk/engine-driven-hook-shaker/gsm-el-toro/ (accessed on 22 April 2023).
  38. Gong, H.J.; Li, J.W.; Wang, F.M.; Mo, Q.H.; Ye, K.Y.; Jiang, Q.S.; Liu, P.P.; Qi, B.B. Hand-Held Kiwi Fruit Thinning Device. P. China CN217308396U, 30 August 2022.
  39. Zhao, J.Z.; Wang, L.X.; Tang, H.; Shu, W.M. An Electric Knapsack Blossom Thinning Machine. P. China CN112930929A, 11 June 2021.
  40. Liu, K.Y.; Liu, Y.L.; Wang, X.D.; Li, J. Hand-Held Pomelo Blossom Thinning Device. P. China CN216492184U, 13 May 2022.
  41. Xyu, L.M.; Yan, C.G.; Ma, S.; Niu, C.; Zhao, S.J.; Wang, S.S.; Yuan, X.T. Hand-Held Bag-Shaped Flower and Fruit Thinning Device. P. China CN212677848U, 12 March 2021.
  42. Zhao, X.; Yang, Y.; Luo, L.J. Hand-Held Citrus Flower Thinning Machine. P. China CN211509900U, 18 September 2020.
  43. Chen, A.M.; Xyu, S.H.; Shang, Z. Electric Flower and Fruit Thinning Device. P. China CN210808375U, 23 June 2020.
  44. Chen, W. Device for Thinning Flower, Fruit and Small Grains Fruit. P. China CN209057550U, 5 July 2019.
  45. Zheng, J.G.; Zheng, J.Y.; Zheng, J.F.; Zheng, J.Y.; Zheng, L.M. Hand-Held Blossom Thinning Machine for Citrus. P. China CN208836605U, 10 May 2019.
  46. Lu, H.Z.; Li, J.; Yang, Z.; Wu, M.C.; Qiu, J.H. Ultrasonic Target Detection Orchard Thinning Machine. P. China CN102217493B, 22 August 2012.
  47. Yang, Z.; Li, J.; Lu, H.Z.; Lin, B.Q.; Tan, J.H.; Wang, W.Z. Electric Orchard Thinner Convenient for Manual Adjustment and Its Use Method. P. China CN102217492B, 7 November 2012.
  48. Lei, X.H.; Lyu, X.L.; Zhang, M.N.; Ma, Z.B.; Chang, Y.H.; Andreas, H. Test and research on electric rotating rope blossom thinner in ‘Cuiguan’ pear orchard. J. Chin. Agric. Mech. 2020, 41, 47–52.
  49. Zhang, B.B.; Ma, R.J.; Guo, L.; Yyu, M.L.; Song, H.F.; Zhang, G.P.; Feng, Z.R. Hand-Held Electric Blossom Thinning Device. P. China CN206791205U, 26 December 2017.
  50. Wang, M.; Wang, H.; Zhang, Q.; Lewis, K.M.; Scharf, P.A. A hand-held mechanical blossom thinning device for fruit trees. Appl. Eng. Agric. 2013, 29, 155–160.
  51. Xyu, C.G.; Zhang, Q.; Zhuang, X.; He, H.Y. Portable Electric Equipment for Fruit Tree Blossom Thinning. P. China CN202617766U, 26 December 2012.
  52. Martin, B.; Torregrosa, A.; Brunton, J.G. Post-bloom thinning of peaches for canning with hand-held mechanical devices. Sci. Hortic. 2010, 125, 658–665.
  53. Martin, B.; Torregrosa, A.; Brunton, J.G. Feasibility of peach bloom thinning with hand-held mechanical devices. Sci. Hortic. 2011, 129, 91–97.
  54. Martin, B.; Torregrosa, A.; Aragon, R.; Brunton, J.G. Portable Mechanical Device for the Clarification of Flowers and Fruit Recience in Trees and Shrubs. P. Spanish ES200901448A, 2 June 2009.
  55. Spornberger, A.; Leder, L.; Bock, K.; Keppel, H.; Modl, P. Impact of thinning methods on yield, diseases and fruit quality of sweet cherries (Prunus avium L.) in organic growing. Erwerbs-Obstbau 2011, 53, 15–22.
  56. Wallis, A.E.; Miranda-Sazo, M.R.; Cox, K.D. Assessing and minimizing the development and spread of fire blight following mechanical thinning and pruning in apple orchards. Plant Dis. 2021, 105, 650–659.
  57. Ngugi, H.K.; Schupp, J.R. Evaluation of the risk of spreading fire blight in apple orchards with a mechanical string blossom thinner. Hortscience 2009, 44, 863–865.
  58. Penzel, M.; Pflanz, M.; Gebbers, R.; Zude-Sasse, M. Tree-adapted mechanical flower thinning prevents yield loss caused by over-thinning of trees with low flower set in apple. Eur. J. Hortic. Sci. 2021, 86, 88–98.
  59. Lordan, J.; Alins, G.; Avila, G.; Torres, E.; Carbo, J.; Bonany, J.; Alegre, S. Screening of eco-friendly thinning agents and adjusting mechanical thinning on ‘Gala’, ‘Golden Delicious’ and ‘Fuji’ apple trees. Sci. Hortice. 2018, 239, 141–155.
  60. Theron, K.I.; Steenkamp, H.; Steyn, W.J. Efficacy of ACC (1-aminocyclopropane-1-carboxylic acid) as a chemical thinner alone or combined with mechanical thinning for japanese plums (Prunus salacina). Hortscience 2017, 52, 110–115.
  61. McClure, K.A.; Cline, J.A. Mechanical blossom thinning of apples and influence on yield, fruit quality and spur leaf area. Can. J. Plant Sci. 2015, 95, 887–896.
  62. Sauerteig, K.A.; Cline, J.A. Mechanical blossom thinning of ‘Allstar’ peaches influences yield and quality. Sci. Hortic. 2013, 160, 243–250.
  63. Baugher, T.A.; Ellis, K.; Remcheck, J.; Lesser, K.; Schupp, J.; Winzeler, E.; Reichard, K. Mechanical string thinner reduces crop load at variable stages of bloom development of peach and nectarine trees. Hortscience 2010, 45, 1327–1331.
  64. Baugher, T.A.; Schupp, J.; Ellis, K.; Remcheck, J.; Winzeler, E.; Duncan, R.; Johnson, S.; Lewis, K.; Reighard, G.; Henderson, G.; et al. String blossom thinner designed for variable tree forms increases crop load management efficiency in trials in four united states peach-growing regions. Horttechnology 2010, 20, 409–414.
  65. Baugher, T.A.; Schupp, J.R.; Lesser, K.M.; Hess-Reichard, K. Horizontal string blossom thinner reduces labor input and increases fruit size in peach trees trained to open-center systems. Horttechnology 2009, 19, 755–761.
  66. Schupp, J.R.; Baugher, T.A. Peach blossom string thinner performance improved with selective pruning. Hortscience 2011, 46, 1486–1492.
  67. Asteggiano, L.; Giordani, L.; Bevilacqua, A.; Vittone, G.; Pellegrino, S.; Costa, G. Bloom mechanical thinning improves fruit quality and reduces production costs in peach. Acta Hortic. 2015, 1084, 389–394.
  68. La Canne Vale. Available online: https://www.lacannevale.fr (accessed on 20 July 2020).
  69. Assirelli, A.; Caracciolo, G.; Roccuzzo, G.; Stagno, F. New tools for mechanical thinning of apricot fruitlets. Agriculture 2021, 11, 1138.
  70. Assirelli, A.; Giovannini, D.; Cacchi, M.; Sirri, S.; Baruzzi, G.; Caracciolo, G. Evaluation of a new machine for flower and fruit thinning in stone fruits. Sustainability 2018, 10, 4088.
  71. Faugno, S.; Cacchi, M.; Sirri, S.; Caracciolo, G.; Giovannini, D.; Quacquarelli, I.; Civitarese, V.; Assirelli, A. Mechanical thinning of apricot fruitlets. Chemi. Eng. Trans. 2017, 58, 259–264.
  72. Clemens. Available online: https://www.clemens-online.com/en/products/ (accessed on 1 December 2022).
  73. Lei, X.H.; Lv, X.L.; Zhang, M.N.; Li, X.; Chang, Y.H.; Andreas, H. Development and test of three arms tractor-mounted flower thinner. J. Trans. Chin. Soc. Agric. Eng. 2019, 35, 31–38.
  74. Lei, X.H.; Lyu, X.L.; Zhang, M.N.; Lu, D.P.; Wang, S.L.; Chang, Y.H.; Zhong, D.X.; Shen, T.B. Performance evaluation of mechanical blossom thinning in trunk type pear orchard. Int. J. Agric. Biol. Eng. 2021, 14, 106–112.
  75. Lammerich, S.; Kunz, A.; Damerow, L.; Blanke, M. Mechanical Crop Load Management (CLM) Improves Fruit Quality and Reduces Fruit Drop and Alternate Bearing in European Plum (Prunus domestica L.). Horticulturae 2020, 6, 52.
  76. Seehuber, C.; Damerow, L.; Blanke, M. Regulation of source: Sink relationship, fruit set, fruit growth and fruit quality in European plum (Prunus domestica L.)-using thinning for crop load management. Plant Growth Regul. 2011, 65, 335–341.
  77. Peifer, L.; Ottnad, S.; Kunz, A.; Damerow, L.; Blanke, M. Effect of non-chemical crop load regulation on apple fruit quality, assessed by the DA-meter. Sci. Hortic. 2018, 233, 526–531.
  78. Damerow, L.; Kunz, A.; Blanke, M. Regulation of fruit set by mechanical flower thinning. Erwerbs-Obstbau 2007, 49, 1–9.
  79. Hehnen, D.; Hanrahan, I.; Lewis, K.; McFerson, J.; Blanke, M. Mechanical flower thinning improves fruit quality of apples and promotes consistent bearing. Sci. Hortic. 2012, 134, 241–244.
  80. Solomakhin, A.A.; Blanke, M. Mechanical flower thinning improves the fruit quality of apples. J. Sci. Food and Agric. 2010, 90, 735–741.
  81. Schupp, J.R.; Baugher, T.A.; Miller, S.S.; Harsh, R.M.; Lesser, K.M. Mechanical thinning of peach and apple trees reduces labor input and increases fruit size. Horttechnology 2008, 18, 660–670.
  82. Miller, S.S.; Schupp, J.R.; Baugher, T.A.; Wolford, S.D. Performance of mechanical thinners for bloom or green fruit thinning in peaches. Hortscience 2011, 46, 43–51.
  83. Philbrownwelding. Available online: https://www.philbrownwelding.com/index.php/peach-blossom-thinner (accessed on 1 December 2022).
  84. Aasted, M.; Dise, R.; Baugher, T.A.; Schupp, J.R.; Heinemann, P.H.; Singh, S. Autonomous Mechanical Thinning Using Scanning LIDAR. In Proceedings of the 2011 ASABE Annual International Meeting, Louisville, KY, USA, 7–10 August 2011.
  85. Lyons, D.J.; Heinemann, P.H.; Schupp, J.R.; Baugher, T.A.; Liu, J. Development of a selective automated blossom thinning system for peaches. Trans. ASABE 2015, 58, 1447–1457.
  86. Li, J.; Xu, Y.; Xu, J.T.; Yang, Z.; Lu, H.Z. Design and experiment of control system for suspended electric flexible thinner. J. Trans. Chin. Soc. Agric. Eng. 2016, 32, 61–66.
  87. Li, J.; Lu, H.Z.; Yang, Z.; Zheng, S.Y. Design and experimental study of litchi flexible thinning mechanism. J. South Chin. Agric. Univ. 2013, 34, 431–435.
  88. Wouters, N.; De Ketelaere, B.; Deckers, T.; De Baerdemaeker, J.; Saeys, W. Multispectral detection of floral buds for automated thinning of pear. Comput. Electron. Agric. 2015, 113, 93–103.
More
© Text is available under the terms and conditions of the Creative Commons Attribution (CC BY) license; additional terms may apply. By using this site, you agree to the Terms and Conditions and Privacy Policy.
Upload a video for this entry
Information
Subjects: Agricultural Engineering
Contributors MDPI registered users' name will be linked to their SciProfiles pages. To register with us, please refer to https://encyclopedia.pub/register :
Xiaohui Lei
,
Quanchun Yuan
,
Tao Xyu
,
Yannan Qi
,
Jin Zeng
,
Kai Huang
,
Yuanhao Sun
,
Andreas Herbst
,
Xiaolan Lyu
View Times: 224
Revisions: 3 times (View History)
Update Date: 21 Nov 2023
Table of Contents
    1000/1000
    Hot Most Recent
    Feedback