You're using an outdated browser. Please upgrade to a modern browser for the best experience.
Ni-Based Catalysts for Biogas Dry Reforming
Edit
This entry is adapted from the peer-reviewed paper 10.3390/catal13091296

Biogas is mainly composed of methane (CH4) (45–75%) and carbon dioxide (CO2) (25–55%), produced by anaerobic digestion of organic compounds, and can be used to produce renewable hydrogen by dry reforming.

hydrogen biogas reforming nickel catalysts

1. Introduction

Interest in renewable energies has increased nowadays due to concerns related to global warming and the depletion of fossil fuel resources. Biogas is considered a sustainable and renewable gaseous fuel because it is produced by the anaerobic digestion of organic compounds. The biomass-derived feedstocks used for biogas production can be seeds, grains, woody crops, agricultural residues, animal manure, sewage sludge, and algae, among others [1].
The worldwide biogas industry has increased by more than 90% between 2010 and 2018, and further growth is still expected [2]. In 2018, 60 × 103 m3 of biogas (35 Mtoe) were produced; Europe (54%) and Asia (30%) were the main producers [3]. The report of the IEA estimates that in 2040, over 260 Mtoe of biogas could be produced worldwide [3].
Biogas is mainly composed of methane (CH4) (45–75%) and carbon dioxide (CO2) (25–55%). Other minor components include nitrogen, oxygen, carbon monoxide, hydrogen sulfide, ammonia, aromatics, and siloxanes [1][4][5][6]. The chemical composition of biogas depends mainly on the origin and quality of the biomass used, the substrate-microorganism relationship, the type of biodigester, and reaction conditions. Typical compositions of raw biogas from different sources are presented in several reviews [1][5][6][7]. In general, the main impurities are H2S, which can reach levels of up to 4000 ppm [4][6][7], and siloxanes [8]. It is noteworthy that much less H2S is contained in raw biogas than in natural gas [7].
Upgrading and purifying technologies are usually necessary to control the level of contaminants, depending on the requirements of biogas utilization. Currently available technologies for removing biogas contaminants include physical and chemical absorption, pressure swing adsorption (PSA), membrane technology, and biological methods [1][5][6][7].
Almost two-thirds of world biogas production was used to generate electricity and heat; around 30% was consumed in buildings, mainly in the residential sector, for cooking and heating, with the remainder upgraded to biomethane and blended into the gas networks or used as a transport fuel [3]. However, biogas has attracted increasing interest as a feedstock to produce high-value-added products, including hydrogen/syngas, methanol, hydrocarbons, and others [1].
Hydrogen is an essential component of a net zero-energy system and has a key role to play in decarbonizing hard-to-abate sectors. The global demand for hydrogen reached 94 Mt in 2021; its market has grown by 6% a year due to the demand from industry (petrochemical, ammonia, and steel) and the transportation sector [9][10]. Almost 96% of H2 produced worldwide comes from non-renewable sources like natural gas, petroleum, and coal. The technological maturity of H2 produced from fossil fuels and the available infrastructure, the possibility of carbon capture and storage, and the development of new catalytic materials evidence the renewed interest in reforming technologies [11]. The reforming process is a mature technology for converting natural gas to hydrogen; when biogas is used as feedstock for reforming, the hydrogen produced can be considered renewable and “green”.
Biogas is suitable for direct conversion into hydrogen via the dry reforming (DR) reaction because it is rich in CH4 and CO2. The great benefit of using DR is the absence of the need to separate CO2 and add other reactants, such as water and oxygen, as in steam reforming, partial oxidation, or autothermal reforming. Sometimes, a small amount of water and/or oxygen is added to favor the total CH4 conversion (because the CO2/CH4 ratio in biogas is usually lower than 1). Although high concentrations of H2S and siloxanes may be found in biogas, which can lead to catalyst degradation, current technologies used in biogas processing have shown that these impurities can be significantly reduced or even eliminated [7][8][12][13]. For example, the removal efficiency of H2S by biological desulphurization reached 100% under optimal conditions [14]. Thus, impurities in biogas are not considered significant concerns during biogas DR [8].

2. Ni-Based Catalysts for Biogas Dry Reforming

Transition metals (including Ni, Fe, and Co) and noble metals (including Pt, Pd, Rh, Ru, and Ir) have been investigated as catalysts for biogas reforming. Catalysts based on noble metals usually have higher activity and greater resistance to coke formation; however, their low availability and high cost limit their applicability. In one of the first studies comparing different metal catalysts for DRM, Rostrup–Nielsen and Hansen [15] found the following activity order (the metals were supported on MgO-stabilized Al2O3): Ru > Rh, Ni > Ir > Pt > Pd, at 500 and 650 °C, while the order for carbon formation was Ni > Pd >> Ir >Pt > Ru, Rh. Ferreira–Aparicio et al. [16] reported a similar order of activity (on a TOF basis) for catalysts supported on γ-alumina at 450 °C: Rh > Ni > Ir > Pt, Ru > Co. Hou et al. [17] compared noble metals supported on γ-alumina at 800 °C, and the catalytic activity exhibited the order Rh > Ru > Pd > Ir, Pt (after 30 min on stream). From these studies, supported Rh catalysts appear to exhibit the best performance in DRM, followed by Ni; considering the much lower cost of Ni, this seems to be a good option. In fact, most catalysts used in the reforming industry are supported by nickel [18].

2.1. Effect of the Catalyst Support and Promoters

Ni-based catalysts have attracted great interest in dry reforming reactions due to their good catalytic activity and low cost. The main problem with these catalysts is that they are also active in carbon formation reactions, which leads to their deactivation. Several approaches have been investigated to overcome deactivation issues, like support choice and the addition of different promoters.
The choice of support has a crucial role in the properties of the catalytic system, as it affects the dispersion of the active phase and the stability of the catalytic system through the metal-support interaction. Moreover, the support can influence the reaction mechanism and the carbon deposition, mainly due to its acidic/basic properties. Many oxides have been studied to support nickel in the DR reaction, like Al2O3, SiO2, MgO, La2O3, and CeO2, among others.
Some authors describe that DRM can follow a bifunctional mechanism in which CH4 is activated on the metal and CO2 on the acidic/basic support [19][20][21][22]. On acidic supports, CO2 activates by forming formate intermediates with the surface hydroxyl groups, and on basic supports, by the formation of oxy-carbonate species [20]. The bifunctional mechanism requires the migration of oxygen and hydrogen species between the metal and the support. Oxygen species that come from the CO2 activation diffuse from the support to the metal surface to oxidize carbonaceous deposits formed by methane decomposition, while hydrogen species diffuse from the metal surface, where CH4 is activated, to the support to react with adsorbed CO2 [21]. For catalysts supported on inert materials like SiO2, the mechanism follows a monofunctional pathway, where both reactants are activated by the metal alone [20][21][22]. Thus, on inert supports, once carbon formation occurs by methane decomposition, subsequent CO2 activation is limited, leading to deactivation. The catalysts supported on inert oxides have relatively weak metal-support interaction and are less active and stable than the mildly acidic (Al2O3) or basic (MgO, La2O3, CeO2) supports.
The correlation between surface acidity–basicity, and catalyst activity, and deactivation in DRM was studied by Das et al. [23] for Ni catalysts supported on SiO2 and Al2O3 (both doped with 1 wt.% CeO2 and 3 wt.% MgO). The supports were prepared by two different methods: the one-step solvothermal method and the sequential impregnation method. A one-step process favors a homogeneous distribution of acidic and basic sites at a moderate concentration, which improves the activity of DRM with fewer side reactions. On the other hand, in the stepwise process, a random distribution of acid/basic sites was observed with fast catalyst deactivation. Catalysts with higher acidity were found to promote methane cracking reactions, while the Boudouard reaction and deactivation owing to metal oxidation were dominant at high basicity.
Alumina is one of the most common supports used in DR reactions as it is inexpensive, has great mechanical and thermal stability, and can achieve high dispersion of the nickel phase. The thermal treatment is an important procedure, determining the reduction degree of the nickel species, the formation of the spinel phase (NiAl2O4), and thus the catalytic behavior and stability of these catalysts. Sahli et al. [24] observed that catalysts formed by a solid solution of Al2O3 and NiAl2O4 without any detectable NiO were more resistant to carbon deposition than the catalyst initially containing NiO in 24 h of DRM at 800 °C. Ribeiro et al. [25] synthesized NiAl2O4 catalysts with a high surface area by the combustion method, and they presented excellent stability on DRM. This was attributed to the rearrangement of nickel in the aluminate matrix and the migration of nickel particles through carbon filaments formed during the activation process with a mixture of O2/CH4. Zhou et al. [26] studied the effect of NiAl2O4 formation on Ni/Al2O3 stability during DRM. A catalyst with strong metal-support interaction was obtained with an increase in the final calcination temperature to 900 °C to form NiAl2O4 exclusively. This catalyst showed high resistance to sintering and coking during a long-term DRM reaction (of about 100 h). Similar results were obtained by Bao et al. [27] for NiCeMgAl catalysts synthesized via the refluxed co-precipitation method: the Ni active sites derived from the NiAl2O4 spinel structure had longer stability in DRM than those derived from the free NiO.
The preparation methodology of Ni/Al2O3 catalysts has a great influence on the activity of DRM. Goula et al. [28] used a new methodology to synthesize Ni/Al2O3 catalysts for DRM. In the equilibrium deposition filtration (EDF) technique, the deposition of the desired species takes place through adsorption and/or surface reaction with the receptor sites developed on the support surface (surface oxygens and surface hydroxyls). The authors used NH4OH solution for pH control and NH4NO3 for adjusting the ionic strength during the nickel deposition on alumina. The catalyst prepared by EDF converted more methane and carbon dioxide at temperatures higher than 700 °C compared with that prepared by the impregnation method. The EDF method provided relatively higher Ni dispersion, indicating that the strong metal-support interactions can suppress the diffusion of Ni2+ into the Al2O3 lattice under mild conditions. Liu et al. [29] showed that the Ni/Al2O3 catalyst synthesized by electrospinning exhibited improved metal dispersion, leading to higher activity and superior coke resistance in DRM compared with the catalyst conventionally prepared by the incipient impregnation method. A bimodal porous alumina support was prepared by Shah et al. [30] via the evaporation-induced self-assembly (EISA) method. The nickel supported on bimodal alumina was synthesized by different methods: freeze drying, wet impregnation, urea deposition-precipitation, and chemical vapor deposition. The stable performance of the bimodally structured catalyst in DRM was related to the combined effect of the metal-support interface and the smaller nickel particle size. The catalyst prepared by urea deposition-precipitation was the most active and stable at 700 °C during 100 h on stream. In the urea deposition-precipitation method, slowly changing the pH of the solution causes progressive precipitation of nickel species, and the formation of large ensembles of nickel species is avoided.
Zhang et al. [31] investigated the effect of different supports (Al2O3, MgO-Al2O3, SiO2, TiO2, ZrO2, and MgO) on the catalytic activity of Ni-based catalysts in DRM. The performance of the tested catalysts decreased in the following order: NiO/MgO-Al2O3 > NiO/SiO2 ≈ NiO/MgO > NiO/Al2O3 > NiO/ZrO2 > NiO/TiO2. For mixed support MgO-Al2O3, Mg2+ ions tend to react with the unsaturated Al3+ centers on the Al2O3 surface, which may reduce the interaction strength between the metal and the support, increasing the metal dispersion. This catalyst was quite stable for 100 h at 750 °C, suggesting a high anti-coking capability. On the other hand, although the initial activity of the Ni/SiO2 catalyst was very high, it decreased gradually with time on stream. The poor catalytic stability of Ni/SiO2 was attributed to the weak interaction between NiO and SiO2, which cannot effectively inhibit the sintering of the active metal Ni during the reaction. Different supports (Al2O3, SiO2, MgO, CeO2, and ZnO) for Ni catalysts were also studied by Gao et al. [32] in biogas DR (CH4/CO2 ratio of 1).
Several authors studied the effect of adding MgO to Ni/Al2O3 catalysts in DRM. Ni/MgO-Al2O3 catalysts with different Mg/Al ratios were studied by Min et al. [33]. Higher catalytic activity was observed for the catalysts with a medium MgO/(MgO + Al2O3) ratio (0.44–0.86), which was attributed to a high specific surface area and high dispersion of Ni particles. The coke resistance increased with increasing MgO loading. The basicity of MgO helps to inhibit carbon deposition by enhancing CO2 adsorption; the adsorbed CO2 reacts with C to regenerate the catalyst. Zhu et al. [34] prepared NiMgAl mixed oxide catalysts derived from hydrotalcite and observed that the mixed oxides with a Mg/Al ratio of 1 exhibited the best catalytic activity and coke resistance. The same result was obtained by Zhan et al. [35] for Ni-Mg-Al catalysts with different Mg contents prepared via a coprecipitation method. The catalyst with 10 mol% Mg and 11 mol% Ni showed the best catalytic activity because of its higher number of basic sites, which caused a minimum amount of carbon deposition on the catalyst.
Ha et al. [36] used Mg-Al mixed oxides derived from hydrotalcites (Mg/Al ratio = 1.3) as supports for Ni catalysts in DRM. The best activity was obtained with the catalyst supported on Mg-Al oxide calcined at 550 °C because it possesses a high surface concentration of Ni. This catalyst presented the highest carbon deposition after 8 h on stream at 600 °C. Modifying the catalyst preparation with citric acid reduced the coke formation and the size of large octahedrally coordinated NiO-like domains, which may easily agglomerate on the surface during DRM. The DRM activity of the NiMgAl mixed oxide catalysts prepared by Nguyen-Phu et al. [37] exhibited a volcano curve as a function of the Mg/Al ratio. The highest activity of the catalyst with a Mg/Al ratio of 1.5 (Ni-Mg1.5AlOx) was attributed to the dispersion of metallic Ni sites and to the high number of basic sites, which are the active sites for CO2 activation. The activity of Ni-Mg1.5AlOx remained stable for 120 h at 727 °C; the high stability was ascribed to its good basicity, suppressing deactivation by coking. Akbari et al. [38] studied the effect of Ni content on the Ni-MgO-Al2O3 catalysts (MgO/Al2O3 = 1) for DRM. The increase in nickel content (from 2.5 to 15 wt.%) increased both the reactant conversions and the amount of deposited carbon (whisker-type carbon).
In addition to MgO, other promoters have been added to Ni/Al2O3 catalysts. A promoter (metal oxide or element) can provide the catalysts with one of the following effects: (1) improve the metal dispersion; (2) enhance the adsorption and activation of CO2, decreasing the coking rate; (3) supply surface oxygen species, being reoxidized by CO2 dissociative adsorption; and (4) “block” carbon growth centers in the metal particles, preventing carbon diffusion and deposition [19].
The Ni/Al2O3 catalysts promoted with alkaline earth metal oxides (MgO, CaO, and BaO) were studied in DRM by Alipour et al. [39]. The highest activity was observed for the MgO-promoted catalyst because the addition of MgO increased the nickel reducibility. Carbon formation was decreased by all three promoters, and this effect was more pronounced for MgO. Different results were obtained by Sengupta and Deo [40], who investigated the addition of MgO and CaO to Ni and Ni-Co/Al2O3 catalysts for DRM. The presence of CaO increased the catalytic activity due to additional sites that could strongly adsorb H2 and CO2. In contrast, MgO presented the opposite effect due to the strong interaction of MgO with the metal phases, decreasing their reducibility. Charisiou et al. [41] compared the effect of MgO and CaO as promoters for Ni/Al2O3 catalysts in biogas DR (CH4/CO2 ratio of 1.5). They concluded that the catalysts promoted with MgO and CaO exhibit higher activity than Ni/Al2O3 catalysts for reaction temperatures between 550 and 750 °C, while the opposite is evidenced for temperatures higher than 750 °C.
Rare earth metal oxides, particularly ceria and lanthanum, have also been studied as supports and promoters for Ni-based catalysts, with promising results. These oxides can improve the dispersion and stabilization of the metal particles and have high activity for the adsorption of CO2. Reduction of bulk CeO2 takes place at temperatures higher than 400 °C, independently of the metal presence, and surface Ce3+ sites can activate CO2 with the formation of CO and simultaneous oxidation of Ce3+ to Ce4+ [19]. The redox property of ceria and its exceptional oxygen storage capacity help prevent carbon deposition [22][42]. In general, bulk CeO2 and La2O3 are not suitable supports for nickel because the metal decorating effect associated with the strong metal-support interaction (SMSI) reduces the catalytic activity. Therefore, these oxides have been used more as promoters for the DR reaction.
The effect of CeO2 loading on Ni/Al2O3 catalysts for DRM was studied by Damyanova et al. [43]. CeO2-containing Ni catalysts exhibited higher activity and stability with time on stream than Ni/Al2O3, which was mainly related to the degree of nickel dispersion on the catalyst surface. The highest activity and stability of the catalyst with 6 wt.% CeO2 were associated with the increase in local electron density and accessibility of the active sites caused by the close contact between nickel and cerium species. The catalyst with the highest amount of CeO2 (12 wt.%) showed a decrease in catalytic activity due to the partial coverage of the active sites by ceria. Li and Veen [44] also showed a partial coverage of the Ni surface on Ni/CeO2 catalysts after high-temperature reduction (≥600 °C), which induces decoration/encapsulation of the Ni particles by a thin layer of reduced ceria. The decoration/encapsulation effect decreased the catalyst activity for the adsorption of CH4 and CO2, leading to lower conversions and decreased carbon deposition in DRM.
Lino et al. [45] studied the effect of adding 5 wt.% of CeO2 to Ni-Mg-Al catalysts derived from hydrotalcites in biogas DR (CH4/CO2 = 1.5) at 650 °C. They only observed a significant increase in activity for the catalyst with 25 wt.% of Ni but not for the catalyst with 10 wt.% of Ni, which was related to the basicity enhancement occasioned by the Ce promotion. Despite its highest basicity, the Ni25%/MgAlCe catalyst was not stable, probably due to Ni sintering. Rosha et al. [46] added 10, 20, and 30 wt.% of CeO2 to the Ni/Al2O3-TiO2 catalyst and observed improved CH4 and CO2 conversions in biogas DR (CH4/CO2 = 1.5) just for the catalyst with 20 wt.% CeO2, in comparison with the catalyst without ceria.
Luisetto et al. [47] prepared Ni/CeO2-Al2O3 catalysts by different methods: co-precipitation (CP), wet impregnation (WI), sol–gel (SG), and citric acid (CA), containing 20 wt.% CeO2. The intrinsic catalytic activity (site time yield) for DRM at 800 °C increased with increasing Ni crystallite size in the following order: CP > WI > SG > CA. The catalyst prepared by the CA method presented a smaller Ni crystallite size (5.8 nm) and a higher content of CeAlO3 species, which both have a role in inhibiting carbon deposition. Ni/CeO2-Al2O3 catalysts (with 10 wt.% CeO2) prepared by impregnation and sol–gel methods were compared by Aghamohammadi et al. [48]. A smaller Ni particle size was obtained for the sol–gel synthesized catalyst, which showed higher activity in DRM. Ni-based mixed CeO2-Al2O3 oxide catalysts prepared by one-pot EISA, containing 20 wt.% CeO2, were investigated by Marinho et al. [49]. The catalysts presented mesoporous structures with highly dispersed Ni as NiAl2O4 spinel clusters. After reduction, Ni particles with small sizes (<5 nm) were observed. The presence of Ce in strong interaction with Al2O3 enhances oxygen mobility and CO2 adsorption, increasing the catalyst activity for DRM and promoting the carbon removal mechanism.
Yang et al. [50] showed that, although the activity of Ni/Al2O3 promoted with both La2O3 and CeO2 (3 wt.% each) was not increased, the carbon deposition in DRM was significantly reduced due to alkaline function and enhancement of metal dispersion. According to Charisiou et al. [51], the modification of Ni/Al2O3 catalysts with CeO2 (10 wt.%) and/or La2O3 (4 wt.%) significantly enhances catalytic performance for biogas DR (CH4/CO2 ratio of 1.5). The catalysts containing lanthanum (Ni/LaAl and Ni/CeLaAl) performed better than the catalysts with only ceria (Ni/CeAl). The high catalytic activity was related to the redox reactions of Ce and La species with the deposited carbon.
The effect of adding CeO2 and La2O3 (10 wt.%) as promoters on the catalytic performance of Ni/Al2O3 was also assessed by Farooqi et al. [52]. The Ni/CeO2-Al2O3 catalyst exhibited higher catalytic activity in DRM at 800 °C due to the increase in reducibility and dispersion of Ni. Meanwhile, Ni/La2O3-Al2O3 presented higher stability during 8 h on stream because La2O3 favors CO2 dissociation. Taherian et al. [53] studied Ni/CaO-Al2O3 catalysts promoted with ceria, lanthana, and yttria (10 wt.%). The ceria-promoted catalyst showed the highest catalyst activity in DRM, which was associated with the smallest Ni crystallite size (8.9 nm). The stability of this catalyst during 30 h on stream was due to the reaction of the carbon species with the lattice oxygen, leading to the self-decoking feature in the presence of ceria.
The addition of CeO2, La2O3, and ZrO2 (5 wt.%) to Ni-Al2O3 catalysts was investigated by Shamskar et al. [54]. The catalysts were prepared by simultaneous co-precipitation of metal nitrate solutions with the assistance of ultrasound irradiation. The incorporation of promoters decreased the catalytic activity of DRM due to the coverage of active sites by the promoters. Among all the promoted catalysts, the Ce-promoted sample exhibited lower carbon formation. Rezaei and Alavi [55] studied the addition of these same oxides (also with 5 wt.%) to Ni/MgAl2O4 catalysts. In this case, the M-MgAl2O4 (M: CeO2, ZrO2, and La2O3) supports were prepared by sol–gel, and Ni was added later by impregnation. The catalysts supported on promoted supports exhibited higher methane conversion in DRM at all temperatures (550–750 °C). The catalyst promoted with CeO2 exhibited the highest activity and the lowest coke formation, which was related to the redox properties of the ceria.
Calgaro et al. [56] evaluated the La/Mg ratio in Ni-Mg-La-Al catalysts derived from hydrotalcites for the biogas DR (CH4/CO2 ratio of 2.33). The increase in the La/Mg ratio decreased the average crystallite size of Ni and increased the strength of acid sites, improving the catalytic activity at 700 °C. The catalyst with La/Mg = 4 presented the best activity and stability due to its greater resistance to sintering and a proper combination of acidic and basic sites. Al-Mubaddel et al. [57] studied the effect of different La2O3 loadings (0 to 20 wt.%) on Ni/Al2O3 catalysts for DRM. The addition of up to 15 wt.% La2O3 in support reduces the content of acid sites and increases the basic sites, including super basic sites (related to unidentate carbonates) that lead to optimum catalytic performance.
Charisiou et al. [58] showed that the Ni/(4 wt.%)La2O3-Al2O3 catalyst is more active and deactivates at a more gradual rate than the Ni/Al2O3 in biogas DR (CH4/CO2 ratio of 1.56). They concluded that doping Al2O3 with La2O3 helps to maintain the Ni0 phase during the reaction due to higher dispersion and stronger metal-support interactions. Moreover, La2O3 addition stabilizes the catalyst by forming a less graphitic type of deposited carbon and enhances its gasification due to the CO2 adsorption on the basic sites. CO2 is activated by La2O3 through the formation of La2O2CO3, which can react with neighboring carbon species to produce CO and regenerate La2O3, eliminating the deposited carbon. Raman spectroscopy was used to investigate the nature and graphitization order of the carbon formed in the spent catalysts. All catalysts presented two broad bands: the G-band between 1500 and 1600 cm−1, and the D-band between 1300 and 1400 cm−1. The G-band is related to intra-layer displacement in the graphene structure, while the D-band is associated with the disorder-induced vibration of the C-C bond. The ratio between the D and G bands (ID/IG) intensities was calculated to show the nature of carbon formed over the catalysts: smaller ID/IG values indicate higher crystallinity due to the higher contribution of the graphitized carbon. The crystallinity degree increases with an increase in the reaction temperature, and this increase was more pronounced for the Ni/Al2O3 catalyst. The catalyst promoted with La2O3 presented higher ID/IG ratio values, showing less graphitic carbon, which is associated with its higher stability during biogas DR.
Several other studies have shown that lanthanum oxycarbonate (La2O2CO3), formed by the reaction of La2O3 with CO2, is of primordial importance in the mechanism of DRM [59][60][61][62]. Li et al. [61] showed that an ordered mesoporous Ni/La2O3 catalyst promoted an increase in the metal-support interface by enhancing Ni dispersion. The CO2-derived species adsorbed at the interface can react quickly with the carbon species generated from CH4 activation on nickel, and therefore, there is no accumulation of La2O2CO3. Thus, this catalyst exhibited superior activity and stability in DRM compared to the catalyst supported on La2O3 prepared by calcination of lanthanum nitrate. In another study of this same research group [62], the Ni/La2O2CO3-Al2O3 catalyst, produced by the calcination of the Ni/La2O3-Al2O3 in the CO2 atmosphere, showed higher activity for DRM than Ni/La2O3-Al2O3. La2O2CO3 prevents Ni from entering the alumina and forming NiAl2O4, increasing Ni reducibility.
The introduction of ZrO2 on Ni/Al2O3 also helps to improve the dissociation of the CO2 reaction, reducing coke formation. Moreover, ZrO2, which is highly dispersed in Al2O3, prevents the formation of the NiAl2O4 phase [63][64][65]. Based on the catalytic activity and coke yield results for DRM, Therdthianwong et al. [63] suggested that the 5–10 wt.% ZrO2 loading range seems to be suitable for reducing coke formation. Similar results were obtained by Anzures et al. [64]: the catalyst with 5 wt.% of ZrO2 presented the best performance in DRM due to the high concentration of the medium-strength basic sites and the high specific surface area, with low carbon formation during 36 h of reaction. Shin et al. [65] prepared Ni/ZrO2-Al2O3 catalysts by the modified Pechini sol-gel method, urea hydrolysis, and physical mixing. The catalyst prepared by Pechini sol-gel showed higher stability for DRM because of the enhanced interaction between nickel and support, promoting CO2 dissociation.
Ceria–zirconia binary oxides have been largely applied as catalyst supports for DRM. Zr4+ stabilizes CeO2, forming solid solutions over all Ce/Zr atomic ratios, and Ce1−xZrxO2 phases exhibit improved textural features, thermal resistance, and oxygen storage/transport properties [19]. According to Iglesias et al. [66], zirconium can be incorporated into ceria cubic lattices up to 15 at.%, while tetragonal features were observed for 25 and 35 at.%. Zr addition enhances support reducibility and metallic dispersion. However, the presence of the zirconium tetragonal phase was detrimental to oxygen mobility. Kumar et al. [67] showed that Ni supported on a ceria–zirconia solid solution was more stable for DRM compared to Ni/ZrO2 and Ni/CeO2 catalysts. The stability of the CexZr1–xO2 solid solution was associated with its enhanced reducibility at lower temperatures. Kambolis et al. [68] observed a significant distortion of the ceria lattice in the ceria-zirconia solid solutions, increasing the number of anion vacancies. These oxygen vacancies are active sites for the dissociative adsorption of CO2, conferring a much higher activity for Ni catalysts in DRM. The zirconium-rich solid solutions exhibited stronger resistance to the formation of carbonaceous deposits.
Wolfbeisser et al. [69] used Ce1−xZrxO2 mixed oxides prepared by co-precipitation and surfactant-assisted co-precipitation as supports for Ni nanoparticles in DRM. The catalyst synthesized by surfactant-assisted co-precipitation was not active for DRM because of the encapsulation of Ni particles by ceria–zirconia particles. The Ni catalyst supported on ceria-zirconia prepared by co-precipitation presented much higher activity than Ni/CeO2. On the other hand, no improvement in catalytic activity was observed when compared to Ni/ZrO2, but the stability against the formation of filamentous coke on the ceria–zirconia catalyst was significantly increased.
The role of ceria dopants on the activity of Ni catalysts for DRM was investigated by Luisetto et al. [70]. Ni/Me0.15Ce0.85O2−δ with Me = Zr4+, La3+, or Sm3+ were prepared by the citric acid synthetic route. All catalysts showed high stability over 50 h of time on stream at 800 °C, with lower formation of filamentous coke on the catalysts doped with La and Sm. The presence of La and Sm increased the number of oxygen vacancies compared to the Zr-doped sample, but they were not capable of enhancing CO2 splitting activity.
Zirconia has also been investigated as a catalytic support in DRM because of its moderate acidity and basicity, high thermal stability, and surface oxygen mobility. Zhang et al. [71] showed that the crystalline structure of ZrO2 support plays an important role in the performance of the Ni catalyst for the DRM. They evaluated amorphous, monoclinic, and tetragonal ZrO2 as supports and concluded that amorphous ZrO2 exhibited higher activity and better stability, which was associated with higher Ni dispersion. In contrast, Ni/m-ZrO2 suffered a continuous decline of activity during 50 h of time on stream, related to the Ni sintering and formation of the encapsulating carbon, which covered the active Ni sites. In another work, this same research group prepared Ni nanoparticles well-dispersed on a mesoporous amorphous zirconia matrix [72]. The anchoring effect promoted by the high surface area of the amorphous structure and the strong interaction between Ni and ZrO2 leads to high catalyst stability in DRM, with high resistance against Ni sintering and carbon deposition. Zhang et al. [73] reported that different distributions of oxygen species over the monoclinic ZrO2 surface can be obtained by treatment under H2, N2, and O2 atmospheres. The treatment in H2 flow promoted the formation of adsorbed oxygen species over the ZrO2 surface, and the Ni supported on this oxide enhanced CO2 activation during DRM, promoting the removal of the deposited carbon.
Lou et al. [74] reported a new approach to synthesize Ni nanoparticles supported on ZrO2 and SiO2 by using air-stable Ni colloids. The Ni/ZrO2 catalyst with a 1.1 nm particle diameter showed high stability for DRM during 60 h on stream, which was attributed to almost all Ni atoms at the perimeter of ZrO2. This led to higher accessibility to the oxygen from CO2 activated at the Ni-ZrO2 interface, promoting the conversion of surface carbon to CO. According to this study, only Ni atoms at the perimeter are stable catalytic sites in DRM for Ni/ZrO2 catalysts.
The effect of adding CeO2 and La2O3 to ZrO2-supported Ni catalysts was studied by Goula et al. [75] in biogas DR (CH4/CO2 ratio of 1.5). The promoted catalysts exhibited enhanced basicity, Ni dispersion, and oxygen ion lability values with superior activity. The Ni/CeO2-ZrO2 catalyst presented higher stability in 28 h of reaction at 750 °C, with lower formation of carbon deposits. In another study, this same group [76] reported a decrease of ~30–35% in the catalytic activity of Ni/ZrO2 during 50 h on stream, and it was limited to less than ~15–20% on the catalysts promoted by La2O3 and CeO2. Higher formation of the more reactive amorphous carbon was observed on the promoted catalysts compared to Ni/ZrO2.
Other materials have been studied as supports for Ni catalysts, such as zeolites and mesoporous materials (SBA-15, MCM-41, etc.). Fakeeha et al. [77] compared the activity of Ni catalysts supported on Al2O3, HY, and H-ZSM-5 for DRM. Ni/H-ZSM-5 presented higher stability with time on stream at 700 °C, with lower carbon deposition. The effect of Si/Al ratios in Na-ZSM-5 for Ni catalysts on DRM was studied by Moradi et al. [78]. Increasing the Si/Al molar ratio (from 30 to 90) resulted in the deviation of zeolite structures to the amorphous phase, decreasing the catalytic activity. The catalyst with a Si/Al ratio equal to 30 showed high stability and resistance to coking during 30 h of reaction at 800 °C.
The sintering of metal particles can be effectively controlled by confining them into pore channels of mesoporous SBA-15 support; moreover, it can also resist the formation of carbon [79]. The influence of the Ni introduction methodology on SBA-15 was evaluated by Gálvez et al. [80]. The catalyst prepared by the chemical reduction-precipitation method using ascorbic acid showed enhanced activity and stability in DRM compared to those prepared by conventional impregnation and precipitation methods. This was associated with the confinement of Ni species (NiO and Ni-phyllosilicates) inside the pores of SBA-15 and preferential carbon growth on the external surface of the catalyst. Karam et al. [81] tuned the properties of nickel nanoparticles inside the mesopores of SBA-15 by controlling the calcination rate. The best stability in DRM was obtained for the catalyst calcined at 0.5 °C min−1 because the strong interaction between the active phase and the SBA-15 support strengthened the Ni nanoparticle confinement and free accessibility without pore plugging. Omoregbe et al. [82] reported that Ni/SBA-15 catalyst activity was stable for DRM during 4 h on stream at 700–800 °C, while a slight drop in activity was observed at 650 °C due to carbon deposition.
Kiani et al. [83] investigated the modification of Ni/SBA-16 with a lanthanum promoter for biogas DR (CH4/CO2 ratio of 1). The presence of La2O3 particles on the catalyst surface decreased the Ni particle size and increased the activity. The maximum activity was obtained for the catalyst with 5.78 wt.%La.
MCM-41-supported nickel catalysts prepared using a facile one-pot method at room temperature were studied by Lovell et al. [84]. The Ni/MCM-41 catalyst showed high activity for DRM, with small nickel particles mostly located inside the MCM-41 pores. Either promoting support acidity by incorporating Al into the MCM-41 framework or reducing support acidity by entrapping Na ions in the MCM-41 pores lowered CH4 conversion and carbon accumulation during DRM. Aguiar et al. [85] compared Si-MCM-41 obtained from rice husk ash and tetraethylorthosilicate (TEOS) as supports for Ni catalysts in DRM. The use of an alternative source of silica did not change the morphology of the material, but there was a significant decrease in the specific surface area, which resulted in lower catalytic activity. Zhang et al. [86] investigated the role of support structure on the catalytic activity of DRM, comparing nickel supported on SiO2, MCM-41, and inverted conical mesoporous silica spheres (MSS). Ni/MSS catalysts exhibited higher activity and stability during 9 h at 800 °C. The inverted-tapered pore structure of MSS improved nickel dispersion and prevented Ni nanoparticle sintering and carbon deposition.
Table 1 summarizes the properties of each supporter and promoter described in this section, highlighting their main advantages and drawbacks.
Table 1. Summary of supports and promoters for Ni catalysts.
Table
  Promoter
Support Al2O3 Basic oxides Reducible oxides
Ex: MgO, CaO
Reduce support acidity
Increase Ni dispersion, promote CO2 adsorption, and inhibit carbon formation		 Ex: CeO2, La2O3
Redox properties with active surface oxygen species
Improve Ni dispersion and prevent carbon deposition
Inert oxides Ex: SiO2
Weak interaction between Ni and support favors sintering
Basic oxides Ex: MgO
Strong basicity decreases Ni reducibility and favors deactivation by metal oxidation
Reducible oxides Ex: CeO2, La2O3, Ce1−xZrxO2
High oxygen storage capacity inhibits carbon deposition
Metal decorating effect due to strong metal-support interaction decreases catalytic activity
Mesoporous Ex: SBA-15, MCM-41
High surface area increases Ni dispersion and confinement of Ni particles into pore channels prevents sintering

2.2. Core-Shell Catalysts

Ni-based catalysts with a core-shell structure have been successfully used in DRM recently. In a core-shell-structured catalyst, the active nanoparticles are encapsulated by a thermally stable coating, inhibiting particle migration and sintering. Moreover, confining Ni particles within a support shell protects the active phase from coke deposition [22].
Zhang and Li [87] prepared core-shell Ni@SiO2 catalysts from NiO nanoparticles (NPs) by a facile method. Multiple NiO cores were formed within a single enclosed shell due to the relatively poor dispersion of the NiO NPs in the CTAB solution. The amorphous silica shell inhibited the formation of filamentous carbon on the nickel surface during DRM. Core-shell-structured Ni@SiO2 catalysts with small-sized Ni NPs (about 5 nm) were synthesized by Wang et al. [88] using a microemulsion method. The silica shell confined the moving space of Ni nanoparticles, providing sintering-free behavior during DRM. At the same time, the small size of Ni NPs provided low carbon diffusion in Ni crystals, reducing coke formation.
Han et al. [89] also showed that small-sized Ni nanoparticles (5.2 nm) catalyzed the DRM without sintering or coke formation when the Ni NPs were protected by a silica overlayer. Ni NPs were immobilized onto functionalized silica nanospheres (Ni/SiO2) and then coated with a silica overlayer. The silica-coated Ni catalyst presented high stability over 170 h of the DRM reaction at 800 °C without any degradation in activity, while the Ni/SiO2 catalyst showed severe deactivation due to sintering and the formation of filamentous carbon. This same research group evaluated Ni/SiO2 catalysts (with Ni NPs of the same size) coated with overlayers of other metal oxides, including Al2O3, MgO, ZrO2, and TiO2 [90]. The following order of initial methane turnover frequency was obtained for DRM at 800 °C: Al2O3 > MgO >> SiO2~ZrO2> TiO2. The enhanced activity of Al2O3 and MgO catalysts was associated with their greater CO2 adsorption. In the case of TiO2, the Ni NPs severely aggregated, resulting in poor activity.
Core-shell structured Ni-SiO2@CeO2 catalyst, with nickel NPs encapsulated between the silica support and ceria shell, was evaluated by Das et al. [91] in biogas DR (CH4/CO2 ratio of 1.5). Ni-phyllosilicate was used as the Ni precursor to produce highly dispersed Ni NPs on SiO2. The Ni-SiO2@CeO2 catalyst presented excellent stability at 600 °C, with no coke detected after 72 h on stream. The higher activity of the core-shell catalyst was related to the high Ni dispersion and reducibility. The CeO2 shell effectively inhibited the growth of filamentous carbon around the active Ni center. On the other hand, the Ni-SiO2 catalyst deactivated during 22 h on stream due to the large deposition of coke and reactor blockage, while the Ni/CeO2 catalyst showed very low activity. Han et al. [92] prepared a (Ni/CeO2)@SiO2 catalyst by confining Ni NPs and CeO2 nanocrystals in SiO2 nanospheres. (Ni/CeO2)@SiO2 catalyst showed higher activity for DRM than Ni@SiO2, which was associated with the smaller size of Ni nanoparticles and the promoting effect of CeO2 on CO2 activation. The silica shell confined the migration of the core components during the reaction, providing resistance to sintering. The Ni-CeO2@SiO2 catalyst was also evaluated by Lin et al. [93] in DRM, and no carbon deposition was observed during 100 h of stability testing at 800 °C. The superior coking and sintering resistance of this catalyst was related to the confinement effect of the porous silica shell and the synergistic interaction between Ni and CeO2 NPs.
Liu et al. [94] developed core-shell Ni-ZrO2@SiO2 catalysts with zirconia-modified nickel NPs (Ni-ZrO2) as the core and microporous silica as the shell. The Ni-ZrO2@SiO2 catalyst showed high stability during 240 h of DRM reaction at 800 °C with no coke formation, while Ni@SiO2 deactivated in 20 h of reaction. The addition of ZrO2 enhanced NiO reducibility and confined Ni species inside the silica shell, inhibiting Ni sintering. Moreover, ZrO2 provided an abundance of activated oxygen to Ni NPs, improving their resistance to coking.
Ce1−xZrxO2 mixed oxides have also been used in Ni core-shell catalysts. Das et al. [95] studied the effect of Zr doping on core-shell Ni-phyllosilicate@Ce1−xZrxO2 catalysts (x = 0 to 0.2). In these core-shell catalysts, the particle size of Ni and its growth during reduction/reaction were independent of the Zr doping. The catalysts with x = 0.05–0.1 in the Ce1−xZrxO2 shell presented a significant increase in the intrinsic activity for DRM at 600 °C. The enhancement in DRM activity by a small amount of Zr doping was attributed to the increase in lattice oxygen mobility of the ceria–zirconia shell and stronger metal-support interaction with Ni. They proposed that the lattice oxygen of the ceria-zirconia at the interface with Ni promotes the oxidation of coke precursors and the dissociation of methane. Marinho et al. [96] synthesized Ni@CeZrO2 (with a Ce/Zr molar ratio of 4.0) and Ni@CeO2 core-shell catalysts by the sol–gel method and compared them with Ni/CeO2 prepared by impregnation. The control of Ni particle size and the high oxygen mobility of the Ni@CeZrO2 catalyst inhibited carbon deposition over 24 h of the DRM reaction at 800 °C. This same research group studied the effect of metal dopants on the performance of Ni@CeMeO2 (Me = Gd, Sm, and Zr) catalysts for DRM [97]. The doping with Zr improved the thermal stability of the catalyst, leading to the formation of small Ni NPs, while Ni metal sintering was observed for Ni@CeO2, Ni@CeGdO2, and Ni@CeSmO2. The Ni@CeZrO2 catalyst showed higher resistance to coke formation during the DRM reaction because of its smaller Ni crystallite size and higher ceria reducibility. On the other hand, the larger Ni particles and poor redox behavior of Ni@CeGdO2 and Ni@CeSmO2 were responsible for the high carbon formation on these catalysts.

2.3. Bimetallic Catalysts

Industrially, Ni-based catalysts are the most widely used for DRM. However, they have some drawbacks, such as catalytic deactivation due to coke deposition and sintering and low catalytic activity when compared to catalysts based on noble metals. An effective strategy to improve the performance of nickel-based catalysts is to use bimetallic Ni catalysts [98][99]. By forming alloys of Ni with other metals, such as transition metals (Co, Cu, Fe) and noble metals (Pt, Rh, Ru), it is possible to enhance reducibility, increase the specific surface area, reduce the size of metallic particles, and inhibit carbon deposition, resulting in a better performance than that of a single Ni catalyst [100].

2.3.1. Ni and Transition Metals

Among Ni-based bimetallic catalysts, Ni-Co bimetallic catalysts have received significant interest. Part of this stems from findings that adding Co to Ni catalysts improves coke formation resistance and increases chemical stability. In addition, bimetallic catalysts demonstrate superior metallic dispersion compared to monometallic catalysts of Ni or Co [101][102][103]. Studies show that Co-based catalysts can reduce the rate of coke formation by oxidizing the carbon deposited on the surface [104][105]. However, monometallic Co catalysts show poor catalytic performance in DRM, which is the main reason for their lower application compared to Ni-based catalysts [106].
Kim et al. [102] prepared a series of catalysts with a fixed Ni content (7.5 wt.%) and Co contents in the range from 0 to 9 wt.% using the evaporation-induced self-assembly (EISA) method. The catalysts were evaluated in the steam methane reforming process. The optimal Co content was 5 wt.%, related to the higher relative concentration of Ni°/Nitotal (37.6%) on the catalyst surface determined by X-ray photoelectron spectroscopy (XPS). Depending on the reaction conditions, a total CH4 conversion was obtained (GHSV = 10,000 mL gcat−1 h−1 and 800 °C). Adding Co to the catalysts drastically reduced the coke production rate and improved the catalytic efficiency during steam methane reforming.
You et al. [107] prepared and evaluated a series of Ni–Co/γ-Al2O3 bimetallic catalysts with a fixed loading of 12 wt.% Ni but with different Co contents for CH4 steam reforming. The results showed that adding Co can effectively improve the resistance to coke formation and the reaction stability of the Ni/Al2O3 catalyst, with a reasonable loss of catalytic activity at lower temperatures (650–750 °C). However, at 800 °C and with GHSV = 18,000 mL gcat−1 h−1, the Ni-Co bimetallic catalysts exhibited the same activity as the Ni/Al2O3 catalyst (CH4 conversion around 90–95%) but with improvements promoted by Co, i.e., reduction in coke production rate and maintenance of catalytic activity during the evaluated period (160 h). XRD and transmission electron microscopy analyses of the reduced catalysts showed that adding Co leads to the formation of Ni-Co alloys on the surface, which play a fundamental role in suppressing coke formation in bimetallic Ni-Co catalysts. However, Ni-Co alloy formation can also block part of the low-coordination Ni active sites and decrease metallic dispersion.
Sheng et al. [105] suggested that Ni and Co act as catalysts for CH4 decomposition and CO2 reduction, respectively, during the DRM reaction, and the carbon deposits combine with active oxygen to release CO, thus regenerating the metal surface. The same result was evidenced by Horlyck et al. [108]. In their work, the investigation of the side reactions (Boudouard, methane cracking, and reverse water-gas shift) demonstrated that Co has a high affinity for removing carbon species deposited via oxidation. At the same time, Ni is more active in the decomposition of CH4. Furthermore, even a low Co load (2.5 wt.%) in the catalysts promotes increased resistance to carbon deposition.
The proportion between Ni and Co in the bimetallic catalyst is a factor that affects methane conversion and synthesis gas quality in reforming processes. Lyu et al. [109] synthesized different Ni-Co/Al2O3 bimetallic catalysts. Keeping the Ni loading fixed at 5 wt.%, the Co content was varied to obtain Co/Ni molar ratios of 0.3, 0.5, 0.7, and 0.9. Employing these catalysts in the DRM at 700 °C, the results showed that the catalyst with a molar ratio of 0.5 presented the best catalytic performance during the 100 h of reaction, presenting CO2 and CH4 conversions of 81.6% and 73.1%, respectively. A similar result was observed by Zolghadri et al. [110] in the steam reforming of methane at 700 °C. Among different Ni-Co/Al2O3-based catalysts, the 10Ni-10Co catalyst presented the best results, with the highest CH4 conversion and H2 yield and the lowest carbon deposition due to improved dispersion of Ni and Co particles.
Several studies show that the Ni-Cu alloy presents better results when compared to Ni monometallic catalysts [111][112][113][114][115], and like Ni, Cu has low costs compared to noble metals. Ni and Cu have a face-centered cubic (fcc) crystalline structure and a similar atomic radius with lattice parameters a = 3.524 Å and 3.615 Å, respectively. Such characteristics favor the formation of a homogeneous solid solution of Ni-Cu. However, Cu tends to segregate on the surface of the Ni/Cu alloy, depending on the temperature and reaction conditions [116][117].
Kitla et al. [118] demonstrated, using the techniques of hydrogen chemisorption and FTIR spectroscopy of CO adsorption, that regardless of the nominal bulk composition of the catalysts, the surface of the bimetallic particles was substantially enriched by Cu with almost the same composition. Naghash et al. [119] observed that at high reduction temperatures (700 °C) and Cu loadings, Cu tended to segregate to reduce interfacial surface energies. Song et al. [120] observed through X-ray photoelectron spectroscopy (XPS) that the surface of the catalysts presents a Cu/Ni molar ratio much higher than the bulk, indicating that the alloy surface is enriched in Cu. In this study, employing hydrotalcite-like compounds (HTlcs) as catalytic precursors, the authors evaluated the effect of monometallic catalysts (Ni and Cu) and four other catalysts with molar ratios of Cu/Ni = 0.1, 0.25, 0.5, and 1.0 in DRM (reaction conditions: 600 °C, CH4/CO2/N2 = 1/1/2, SV = 60,000 mL gcat−1 h−1). The Ni monometallic catalyst initially showed a slight increase in the CH4 and CO2 conversions and H2/CO ratio with time on stream, with a maximum of 51%, 63%, and 0.8, respectively. However, the conversions and the H2/CO ratio decreased after approximately 10 h on the stream, which was attributed to catalytic deactivation by coke formation. On the other hand, the Cu monometallic catalyst showed much lower conversions (<5%), indicating that metallic Cu has low activity for the reaction. The performance of bimetallic catalysts was dependent on the alloy composition. Catalysts with Cu/Ni ratios = 0.25 and 0.5 showed a drastic improvement in catalytic performance, and both catalysts exhibited stable activity during the investigated period (25 h), with high resistance to coke formation. This resistance was associated with a decrease in CH4 decomposition and an increase in CO2 dissociation as a result of Ni-Cu alloying. The activity of the Cu/Ni = 0.25 catalyst is close to that of thermodynamic equilibrium and slightly higher than that of the Cu/Ni = 0.5 catalyst, which can be attributed to the higher number of Ni active sites on the surface. At higher Cu loading (Cu/Ni = 1.0), there is a decrease in activity and catalytic stability, indicating that there exists an optimal Ni-Cu composition.
Nataj et al. [121] observed similar results using different contents of Ni (5, 7.5, and 10 wt.%) and Cu (0, 1, 2, 3, and 4 wt.%) supported on alumina in the DRM. Under optimized conditions, it was observed that low Cu contents (1 wt.%) promoted high activity and catalytic stability with higher resistance to coke deposition as well as high resistance to sintering of the active phase. However, catalysts with high Cu loadings (2, 3, and 4 wt.%) were less active and deactivated, mainly due to active site sintering and Ni coverage by the Cu-enriched phase. Under optimized conditions, using a catalyst with 10 wt.% of Ni and 0.83 wt.% of Cu at 750 °C, CH4 and CO2 conversions above 95% were obtained with a H2/CO ratio = 1. A similar result was observed by Lee et al. [122] in DRM. Catalysts with 10 wt.% Ni supported on γ-Al2O3 were prepared with 1, 5, 7.5, and 10 wt.% Cu by the wet impregnation method. The 1 wt.% Cu addition to the Ni/Al2O3 catalyst improved the stability and activity during 16 h on stream, showing a stable CH4 conversion of about 90%. This increase in performance was associated with the suppression of carbon deposition. However, catalysts with content greater than 5 wt.% Cu deactivated faster (8–10 h) than the Ni/Al2O3 catalyst due to the increased coke deposition.
Han et al. [123] evaluated DRM on catalysts with low loadings of Ni (4 wt.%) and Cu (0.2, 0.5, and 1.5 wt.%) supported on SiO2, which were prepared by electrostatic adsorption of the Ni-ammonia and Cu-ammonia complexes. Over the entire temperature range evaluated (600–750 °C), the catalyst with a Cu content of 0.5 wt.% was the one that presented the highest performance, displaying conversions of CH4, CO2, and H2/CO ratios around 80%, 85%, and 0.9, respectively. Except for the catalyst with 0.5 wt.% Cu, all catalysts showed activity loss with time on stream (50 h) at 750 °C. The superior performance of this catalyst was associated with the smaller alloy size and an appropriate addition of Cu, which promoted CO2 activation. The authors also observed that a higher Cu loading (1.5 wt.%) favors the formation of Cu clusters, which could cover more Ni atoms on the surface and make CH4 activation more difficult.
The synergistic effect between Ni and Fe has been investigated by several researchers in methane reforming. Although Fe has low activity in methane steam reforming, it has high activity in the WGSR reaction and easily forms alloys with Ni [124]. The study carried out by Kim et al. [125], combining the techniques operarando XRD and X-ray absorption spectroscopy (XAS), observed that under DRM conditions, the Fe is partially oxidized to FeO, leading to partial segregation and the formation of a Ni-rich NiFe alloy. FeO is preferably formed on the catalyst surface, which reacts through a redox mechanism with carbon deposits to form CO, and then the Ni-Fe alloy is regenerated. The authors proposed that due to the absence of detection of any phase of FeO in the XRD, FeO is likely to be located on the surface as small domains covering a fraction of the surface of the Ni-rich particles, thus providing that carbon removal sites (FeO) are close enough to active sites (Ni) for methane reforming. These findings may explain the increased catalytic stability of bimetallic Ni-Fe catalysts.
The control of the composition of the Ni-Fe alloy is fundamental for good catalytic performance, and this is directly related to the preparation method of the catalysts [126]. As highlighted by Tomishige et al. [126], traditional methods such as co-impregnation are not efficient for producing uniform Ni-Fe alloy particles, as is the case with the impregnation of Ni in mixed oxide supports containing Fe. The Ni-Fe alloy is generated during the reduction; however, controlling the Ni/Fe ratio is very difficult. Otherwise, synthesizing catalysts using precursor oxides containing Ni and Fe, such as hydrotalcite-type compounds and perovskites, is more effective for obtaining Ni-Fe alloy particles with a controlled composition. The effect of Fe in the Ni-Fe alloy has positive and negative aspects for the catalytic activity. The breaking of C-H bonds occurs mainly on the surface of Ni atoms, and the formation of the Ni-Fe alloy decreases the number of surface Ni atoms. On the other hand, Fe can be oxidized more easily than Ni, and the presence of oxidized Fe species is related to positive aspects since this is where the carbonaceous species are oxidized [126]. Therefore, synthesizing catalysts with an adequate Fe composition in the Ni-Fe alloy is fundamental for obtaining high activity and stability.
Braga et al. [124] synthesized Ni and Fe catalysts supported on CeO2 by two different methodologies, incipient wetness impregnation (IWI) and mechanochemical ball milling (BM), and evaluated the performance of these catalysts in the steam reforming of methane. The characterization of the catalysts showed that adding Fe increased the dispersion of Ni-Fe particles compared to the monometallic catalyst (Ni/CeO2). Catalysts synthesized by the mechanochemical methodology showed the highest reducibility and H2 production rate, and these results were correlated to smaller particle sizes (Ni or NiFe) and stronger metal-support interactions. The performance of the Fe0.1Ni0.9/CeO2-BM catalyst was similar to that of the monometallic catalyst at high temperatures (950 °C). However, coke formation was practically null on the bimetallic catalyst, while the monometallic catalyst showed high coke deposition, even in the catalytic evaluation carried out for a few hours.
Li et al. [127] prepared Ni and Fe catalysts with the content of metal Ni and Fe of 7.25% and 2.49% for Ni3Fe1/Al2O3 and 4.98% and 5.03% for Ni1Fe1/Al2O3, respectively, by an evaporation-induced self-assembly method. Both catalysts showed relative stability in DRM during the evaluated period (50 h). However, the catalyst with equimolar content (Ni1Fe1/Al2O3) showed higher CH4 and CO2 conversion values and higher H2/CO molar ratios. This result was associated with the greater availability of FeOx in the dealloying process offered by the catalyst in the equimolar composition. The authors observed a structural evolution of the Ni-Fe alloy during DRM. Due to the segregation of Fe from Ni-Fe alloys during DRM, the spent Ni1Fe1/Al2O3 and Ni3Fe1/Al2O3 catalysts formed particles of Ni3Fe1 alloy and Ni, respectively.
Song et al. [128] evaluated the effect of adding Fe on the Ni/Al2O3 catalyst in low-temperature DRM. The catalysts were synthesized by a modified evaporation-induced self-assembly (mEISA) method, including a microwave treatment and an EISA process. The performance of the bimetallic catalyst (9.6 wt.% Ni and 4.2 wt.% Fe) was superior to that of the monometallic catalyst (15.7 wt.% Ni) in the entire temperature range evaluated (400–550 °C), with a maximum conversion of 26.6% to CH4 and 37.8% for CO2 and with an H2/CO molar ratio close to 0.7. During the stability tests, the bimetallic catalyst showed stable catalytic activity throughout the evaluated period (20 h). On the other hand, the monometallic catalyst showed a gradual reduction in the conversion of CH4 and CO2. The characterizations of the spent catalysts showed that on the NiFe/Al2O3 catalyst, there was the formation of FeOx due to the segregation of Fe, and this promoted the stabilization of the metallic state of Ni. Three species of carbon deposition were identified in the spent catalysts: active carbon (Cα), less active carbonaceous species (Cβ), and inactive graphitic carbon (Cγ). The authors observed that in the absence of Fe in the catalyst, the active species of Cα could not be converted quickly and effectively into CO. These species accumulated and crystallized, generating even more carbonaceous species of the Cβ and Cγ types, leading to the deactivation of the Ni/Al2O3 catalyst. Furthermore, there was a large formation of carbon filaments and encapsulated coke with high graphitization on the Ni/Al2O3 catalyst and only partially encapsulated coke with low graphitization on the NiFe/Al2O3 catalyst. Thus, forming the metallic alloy (Ni-Fe) increased the resistance to coke deposition.
Thalinger et al. [129] synthesized two perovskites, La0.6Sr0.4FeO3−δ (lanthanum strontium ferrite, LSF) and SrTi0.7Fe0.3O3-δ (strontium titanium ferrite, STF), and then the perovskites were impregnated with Ni (10 mol%). The Ni/Al2O3 catalyst was synthesized by coprecipitation as a reference. After treatment with H2, Ni-Fe alloy formation was observed due to Fe exsolution in LSF and STF catalysts. However, the LSF catalyst showed higher Ni-Fe alloying due to its greater reducibility than STF, which suppressed catalytic performance in methane steam reforming. The more reducible the perovskite support, the stronger the deviation from the catalytic behavior of Ni/Al2O3. The authors concluded that the activity of supported Ni–Fe catalysts could be controlled by carefully selecting the complex oxide support and reduction conditions.

2.3.2. Ni and Noble Metals

The literature unanimously points out that the main factors affecting the stability of Ni catalysts in DRM are related to coke formation and sintering processes. Both processes are related to the high temperatures typically employed in DRM. The sintering process is thermodynamically favored by the high temperatures used in DRM, resulting in losses of metal surface area and, consequently, a decrease in the number of active sites of the catalyst. Activity loss can also occur due to carbon deposition on the catalyst’s active sites. Furthermore, the DRM operation can be interrupted by reactor obstruction caused by excessive coke formation [130][131].
Several measures can be taken to prevent the processes that lead to the deactivation of Ni-based catalysts. One of these measures is controlling the size of the metallic sites on the surface because the sites that produce carbon are larger than those required for CH4 reforming. By forming alloys of Ni with noble metals, it is possible to control the size of the metallic sites and thus regulate the deposition and gasification of carbon on the catalysts [100][131][132]. This effect can be observed in the work of Pawelec et al. [133], where different Pt (0.3–0.5 wt.%) and Ni (1–12 wt.%) catalysts supported on ZSM-5 zeolite were prepared and evaluated in DRM at 500 °C. The catalytic test conducted using the Pt6Ni catalyst (0.5 wt.% Pt and 6 wt.% Ni) showed no significant deactivation during the evaluated period, and the stability of this catalyst was attributed to the presence of small Ni metal particles on the catalyst surface, which were generated by a “dilution” effect promoted by Pt, resulting in higher Ni dispersion. Although carbon formation was not completely suppressed, it was significantly reduced during the catalytic test conducted with the Pt6Ni catalyst. Furthermore, the deposition of carbon on the surface of the Ni crystals did not significantly affect the catalytic activity of this catalyst.
The activity of Pt and Ni bimetallic catalysts can also be enhanced by the synthesis methodology employed. García-Diéguez et al. [131] synthesized monometallic and bimetallic Pt and Ni catalysts supported on nanofibrous γ-Al2O3 using two distinct methodologies, reverse microemulsion (ME) and incipient wetness impregnation (IM), and these catalysts were evaluated in DRM. Characterization of the catalysts revealed that the addition of Pt and the ME synthesis favored the formation of NiO instead of the nickel aluminate phase, resulting in a facilitated reduction of NiO to Ni° during the pretreatment. The ME synthesis positively influenced the overall carbon formation, reducing its formation by 90% and 70% compared to the 4Ni/Al2O3 and 0.04Pt4Ni/Al2O3 catalysts, respectively. Stability tests at 700 °C showed that all catalysts synthesized by ME exhibited more stable results. Additionally, the addition of Pt to Ni catalysts had a beneficial effect, particularly for the catalyst prepared by ME. Thus, the activity and stability of the catalysts can be improved by adding Pt and choosing the catalyst preparation method.
Dai et al. [134] encapsulated Ni-Pt catalysts supported on silicalite-1 in a hollow zeolite. Catalytic tests of DRM (800 °C, atmospheric pressure, GHSV = 72,000 mL gcat−1 h−1, and CH4/CO2 = 1) revealed that the encapsulated catalysts exhibited high stability and resistance to carbon deposition. The initial conversions of CO2 and CH4 were 78–83% and 75–80%, respectively. However, after only 1 h of time on stream, the monometallic Ni catalyst (1.5 wt.%) without encapsulation (1.5Ni/S-1) was deactivated completely, while the bimetallic catalyst (1.5 wt.% Ni and 0.5 wt.% Pt) without encapsulation (1.5Ni-0.5Pt/S-1) showed a continuous activity loss and was deactivated after 6 h of time on stream. With the encapsulation of these catalysts, it was possible to maintain high activity without any signs of deactivation throughout the evaluated period (6 h). Among the encapsulated catalysts (1.5Ni@Hol S-1 and 1.5Ni-0.5Pt@Hol S-1), the bimetallic catalyst exhibited higher conversions of CO2 (83%), and CH4 (77%). The authors performed thermogravimetric analysis (TGA) to determine the amount of carbon deposited on the catalysts after 6 h on the stream. The 1.5Ni-0.5Pt@Hol S-1 catalyst showed only a 1% mass loss, while the 1.5Ni-0.5Pt/S-1 catalyst exhibited a mass loss of 11.4%, a similar value to that exhibited by the 1.5Ni@Hol S-1 catalyst (10.3%). The significant catalytic deactivation observed for the 1.5Ni/S-1 catalyst can be attributed to the rapid carbon deposition on this catalyst since it exhibited a mass loss of 31%.
The beneficial effect of adding Pt to Ni-based catalysts supported on Al2O3 for DRM could be observed in the works of the García–Diéguez group [135][136]. These studies have shown that adding Pt to Ni catalysts reduces the size of the metallic crystals compared to monometallic Pt and Ni catalysts. An increase in catalytic activity can be achieved not only by introducing a small amount of Pt (0.4 wt.%) into Ni catalysts (10 wt.%) but also by adding a higher amount of Ni (10 wt.%) to Pt (4 wt.%) catalysts. These findings indicate the existence of a synergistic effect between Pt and Ni. Furthermore, adding small amounts of Pt significantly increases the stability of Ni-based catalysts, as Pt inhibits coke deposition and reduces the operating temperature. The loss of CO2 conversion was reduced from 1.4% h−1 to 0.4% h−1 with the addition of 0.4 wt.% of Pt to the Ni catalyst (10 wt.%) supported on Al2O3 in stability tests (14 h) of DRM at 700 °C.
In addition to the sintering of metallic particles, operating DRM at high temperatures leads to the segregation of the Pt-Ni alloy. In the study conducted by Egelske et al. [137], Pt and Ni catalysts supported on γ-Al2O3 were prepared and evaluated in DRM at different temperatures. The results revealed that DRM at 700 °C promotes the segregation of Pt-Ni alloy particles; consequently, the Pt-rich ensembles induce methane activation in coke, leading to catalyst deactivation. The authors presented evidence that the observed loss of catalytic activity was associated with increased coke formation. Although sintering processes occurred, they did not play a significant role in the activity loss.
In addition to Pt-Ni alloys, Ni alloys with other noble metals, such as Rh, Pd, and Ru, have been evaluated in DRM. Hou et al. [17] evaluated different metals (Ru, Rh, Pt, Pd, Ir, Ni, and Co) in DRM, and among the noble metals, Rh showed the best results in terms of resistance to carbon deposition and higher catalytic activity. Thus, Rh was selected to be added to Ni at different molar ratios. The reactions, carried out at 800 °C with CH4/CO2 = 1, 60,000 mL gcat−1 h−1 and atmospheric pressure, revealed that the reforming activity of the bimetallic catalysts (Rh-Ni) increased with an increase in the Rh loading, while the coke formation rate decreased. Although the catalytic tests lasted only 4 h, the reactions performed with catalysts having Rh/Ni molar ratios greater than 0.1 did not display coke formation. Even increasing the space velocity to 150,000 mL g−1 h−1, no coke deposition was detected in the catalytic test with the catalyst composed of the molar ratio Rh/Ni = 0.1.
Due to DRM being an endothermic reaction and the carbon being easily formed at low temperatures, it is more appropriate to carry out DRM at temperatures above 800 °C. However, the operation at low temperatures could save resources and costs and limit the sintering processes at active sites [138]. Thus, searching for a catalyst that exhibits resistance to coke deposition during DRM operation at lower temperatures is necessary. With this intention, Mao et al. [139] synthesized monometallic catalysts of Rh (2.2 wt.%) and Ni (2.2 wt.%) and bimetallic catalysts of Rh (0.6 wt.%)-Ni (1.6 wt.%) supported on MgAl2O4, and evaluated them in biogas DR. The reaction conditions were 400–800 °C, CH4/CO2 = 1, WHSV = 18,000 mL gcat−1 h−1, and atmospheric pressure. The catalytic evaluations conducted at 600 °C showed initial conversions of CH4 and CO2 of around 42% and 53%, respectively, for all catalysts. During the stability test, the Ni-MgAl2O4 catalyst showed a continuous loss of catalytic activity. On the other hand, the Rh-MgAl2O4 and RhNi-MgAl2O4 catalysts showed no apparent deactivation during the 20 h of evaluation. By evaluating the carbon deposition on the spent catalysts, a mass loss of 21% was obtained for the Ni-MgAl2O4 catalyst and only 1.5% for Rh-MgAl2O4, while the bimetallic catalyst showed no mass loss. Thus, the authors suggest that the presence of Rh significantly increases the performance of the catalysts in terms of resistance to carbon deposition during DRM.
Jóźwiak et al. [140] reported similar results, where a series of monometallic (Rh and Ni) and bimetallic (Rh-Ni) catalysts with a metallic content of 5 wt.% supported on SiO2 were synthesized and evaluated in DRM. After 24 h on stream at 700 °C, the catalysts were evaluated concerning activity loss and carbon deposition. The Ni monometallic catalyst exhibited the highest activity loss (7.31%) among all catalysts, while the Rh monometallic catalyst presented an activity loss of 2.86%. The TGA of the spent Ni monometallic catalyst showed a mass loss of 21.6%, while there was no mass loss for the spent Rh monometallic catalyst. The bimetallic catalysts showed distinct performances depending on the Rh and Ni content. The activity loss was reduced with an increase in the Rh content in the catalysts, so that the 3.75Ni-1.25Rh, 2.5Ni-2.5Rh, and 1.25Ni-3.75Rh catalysts presented activity losses of 5.96%, 1.58%, and 1.12%, respectively. In contrast, carbon deposition did not follow the same trend, obtaining mass losses of 34.2%, 42.1%, and 1%, respectively. This considerable amount of carbon deposition on the catalyst surface was associated with the Ni-rich metallic phase. Furthermore, the authors suggested that although high carbon deposition occurred on the 2.5Ni-2.5Rh catalyst, the low activity loss (1.58%) observed is due to the type of carbon deposited, which has graphite-like structures.
Romano et al. [141] synthesized several mono and bimetallic catalysts based on Ni, Rh, and Pd supported on γ-Al2O3 and CeO2-Al2O3. DRM catalytic tests performed at 700 °C, CH4/CO2 = 1, and WHSV = 30,000 mL gcat−1 h−1 revealed that the Ni monometallic catalysts suffered deactivation by coke deposition. In contrast, the Rh monometallic catalysts showed remarkable activity and stability, with no evidence of deactivation during the evaluated period (96 h). Adding Rh to Ni monometallic catalysts enhanced the reducibility of nickel oxide species and increased the catalytic activity. The CH4 and CO2 conversions obtained by the 15%Ni/CeO2-Al2O3 catalyst in 48 h of reaction were 57.7% and 72.4%, respectively. With the addition of 1% Rh (14%Ni1%Rh/CeO2-Al2O3), the conversions obtained were increased to 68.3% (CH4) and 81.4% (CO2). On the other hand, Pd-based catalysts showed low catalytic performance. The Pd/CeO2-Al2O3 monometallic catalysts lost their catalytic activity due to coke deposition, and the bimetallic catalyst (14.5%Ni0.5%Pd/CeO2-Al2O3) presented conversions similar to the catalytic test performed with 15%Ni/Al2O3 catalyst, where conversions of 51.6% and 63.8% were obtained for CH4 and CO2, respectively, after 48 h.
Other researchers have investigated the addition of Pd to Ni-based catalysts with promising results. The metals Pd and Ni do not form alloys, mainly because Pd has a lower surface tension and a larger atomic radius than Ni [142]. Ma et al. [143] evaluated the addition of Pd to Ni catalysts supported on ordered mesoporous alumina (MA). The Pd/MA catalyst showed the lowest initial conversion of CH4 and CO2, around 75% and 82%, respectively. After 8 h of catalytic evaluation, the Pd/MA catalyst presented a significant loss of catalytic activity. The other catalysts maintained high CH4 and CO2 conversion values during the 100 h evaluation. While the Ni/MA catalyst showed a slight activity loss, the PdNi/MA bimetallic catalyst remained completely stable during the evaluation period. The carbon deposition on the spent catalysts was analyzed using TGA, TEM, and Raman techniques. It was observed that the bimetallic catalyst had the lowest coke deposition, and the addition of Pd prevented the formation of filamentous carbon, which was associated with a loss of catalyst activity.

References

  1. Gao, Y.; Jiang, J.; Meng, Y.; Yan, F.; Aihemaiti, A. A Review of Recent Developments in Hydrogen Production via Biogas Dry Reforming. Energy Convers. Manag. 2018, 171, 133–155.
  2. Abanades, S.; Abbaspour, H.; Ahmadi, A.; Das, B.; Ehyaei, M.A.; Esmaeilion, F.; El Haj Assad, M.; Hajilounezhad, T.; Jamali, D.H.; Hmida, A.; et al. A Critical Review of Biogas Production and Usage with Legislations Framework across the Globe. Int. J. Environ. Sci. Technol. 2022, 19, 3377–3400.
  3. International Energy Agency. Outlook for Biogas and Biomethane: Prospects for Organic Growth. 2020. Available online: https://www.iea.org/reports/outlook-for-biogas-and-biomethane-prospects-for-organic-growth/annex (accessed on 22 February 2023).
  4. Alves, H.J.; Bley Junior, C.; Niklevicz, R.R.; Frigo, E.P.; Frigo, M.S.; Coimbra-Araújo, C.H. Overview of Hydrogen Production Technologies from Biogas and the Applications in Fuel Cells. Int. J. Hydrogen Energy 2013, 38, 5215–5225.
  5. Ullah Khan, I.; Hafiz Dzarfan Othman, M.; Hashim, H.; Matsuura, T.; Ismail, A.F.; Rezaei-DashtArzhandi, M.; Wan Azelee, I. Biogas as a Renewable Energy Fuel—A Review of Biogas Upgrading, Utilisation and Storage. Energy Convers. Manag. 2017, 150, 277–294.
  6. Awe, O.W.; Zhao, Y.; Nzihou, A.; Minh, D.P.; Lyczko, N. A Review of Biogas Utilisation, Purification and Upgrading Technologies. Waste Biomass Valorization 2017, 8, 267–283.
  7. Sun, Q.; Li, H.; Yan, J.; Liu, L.; Yu, Z.; Yu, X. Selection of appropriate biogas upgrading technology-a review of biogas cleaning, upgrading and utilisation. Renew. Sustain. Energy Rev. 2015, 51, 521–532.
  8. Jung, S.; Lee, J.; Moon, D.H.; Kim, K.H.; Kwon, E.E. Upgrading biogas into syngas through dry reforming. Renew. Sustain. Energy Rev. 2021, 143, 110949.
  9. International Energy Agency. The Future of Hydrogen; OECD: Paris, France, 2019.
  10. International Energy Agency. Global Hydrogen Review 2022; OECD: Paris, France, 2022.
  11. Prato-Garcia, D.; Robayo-Avendaño, A.; Vasquez-Medrano, R. Hydrogen from Natural Gas and Biogas: Building Bridges for a Sustainable Transition to a Green Economy. Gas Sci. Eng. 2023, 111, 204918.
  12. Lau, C.S.; Tsolakis, A.; Wyszynski, M.L. Biogas upgrade to syn-gas (H2-CO) via dry and oxidative reforming. Int. J. Hydrogen Energy 2011, 36, 397–404.
  13. Araki, S.; Hino, N.; Mori, T.; Hikazudani, S. Autothermal reforming of biogas over a monolithic catalyst. J. Nat. Gas Chem. 2010, 19, 477–481.
  14. Vikrant, K.; Kailasa, S.K.; Tsang, D.C.W.; Lee, S.S.; Kumar, P.; Giri, B.S.; Singh, R.S.; Kim, K.-H. Biofiltration of hydrogen sulfide: Trends and challenges. J. Clean. Prod. 2018, 187, 131–147.
  15. Rostrup-Nielsen, J.R.; Hansen, J.H.B. CO2-Reforming of Methane over Transition Metals. J. Catal. 1993, 144, 38–49.
  16. Ferreira-Aparicio, P.; Guerrero-Ruiz, A.; Rodríguez-Ramos, I. Comparative Study at Low and Medium Reaction Temperatures of Syngas Production by Methane Reforming with Carbon Dioxide over Silica and Alumina Supported Catalysts. Appl. Catal. A Gen. 1998, 170, 177–187.
  17. Hou, Z.; Chen, P.; Fang, H.; Zheng, X.; Yashima, T. Production of Synthesis Gas via Methane Reforming with CO2 on Noble Metals and Small Amount of Noble-(Rh-) Promoted Ni Catalysts. Int. J. Hydrogen Energy 2006, 31, 555–561.
  18. Aramouni, N.A.K.; Touma, J.G.; Tarboush, B.A.; Zeaiter, J.; Ahmad, M.N. Catalyst Design for Dry Reforming of Methane: Analysis Review. Renew. Sustain. Energy Rev. 2018, 82, 2570–2585.
  19. Papadopoulou, C.; Matralis, H.; Verykios, X. Catalysis for Alternative Energy Generation; Guczi, L., Erdôhelyi, A., Eds.; Springer: New York, NY, USA, 2012; ISBN 978-1-4614-0343-2.
  20. Pakhare, D.; Spivey, J. A Review of Dry (CO2) Reforming of Methane over Noble Metal Catalysts. Chem. Soc. Rev. 2014, 43, 7813–7837.
  21. Ferreira-Aparicio, P.; Rodríguez-Ramos, I.; Anderson, J.; Guerrero-Ruiz, A. Mechanistic Aspects of the Dry Reforming of Methane over Ruthenium Catalysts. Appl. Catal. A Gen. 2000, 202, 183–196.
  22. Abdulrasheed, A.; Jalil, A.A.; Gambo, Y.; Ibrahim, M.; Hambali, H.U.; Shahul Hamid, M.Y. A Review on Catalyst Development for Dry Reforming of Methane to Syngas: Recent Advances. Renew. Sustain. Energy Rev. 2019, 108, 175–193.
  23. Das, S.; Sengupta, M.; Patel, J.; Bordoloi, A. A Study of the Synergy between Support Surface Properties and Catalyst Deactivation for CO2 Reforming over Supported Ni Nanoparticles. Appl. Catal. A Gen. 2017, 545, 113–126.
  24. Sahli, N.; Petit, C.; Roger, A.C.; Kiennemann, A.; Libs, S.; Bettahar, M.M. Ni Catalysts from NiAl2O4 Spinel for CO2 Reforming of Methane. Catal. Today 2006, 113, 187–193.
  25. Ribeiro, N.F.P.; Neto, R.C.R.; Moya, S.F.; Souza, M.M.V.M.; Schmal, M. Synthesis of NiAl2O4 with High Surface Area as Precursor of Ni Nanoparticles for Hydrogen Production. Int. J. Hydrogen Energy 2010, 35, 11725–11732.
  26. Zhou, L.; Li, L.; Wei, N.; Li, J.; Basset, J. Effect of NiAl2O4 Formation on Ni/Al2O3 Stability during Dry Reforming of Methane. ChemCatChem 2015, 7, 2508–2516.
  27. Bao, Z.; Lu, Y.; Han, J.; Li, Y.; Yu, F. Highly Active and Stable Ni-Based Bimodal Pore Catalyst for Dry Reforming of Methane. Appl. Catal. A Gen. 2015, 491, 116–126.
  28. Goula, M.A.; Charisiou, N.D.; Papageridis, K.N.; Delimitis, A.; Pachatouridou, E.; Iliopoulou, E.F. Nickel on Alumina Catalysts for the Production of Hydrogen Rich Mixtures via the Biogas Dry Reforming Reaction: Influence of the Synthesis Method. Int. J. Hydrogen Energy 2015, 40, 9183–9200.
  29. Liu, L.; Wang, S.; Guo, Y.; Wang, B.; Rukundo, P.; Wen, S.; Wang, Z. Synthesis of a Highly Dispersed Ni/Al2O3 Catalyst with Enhanced Catalytic Performance for CO2 Reforming of Methane by an Electrospinning Method. Int. J. Hydrogen Energy 2016, 41, 17361–17369.
  30. Shah, M.; Das, S.; Nayak, A.K.; Mondal, P.; Bordoloi, A. Smart Designing of Metal-Support Interface for Imperishable Dry Reforming Catalyst. Appl. Catal. A Gen. 2018, 556, 137–154.
  31. Zhang, R.; Xia, G.; Li, M.; Wu, Y.; Nie, H.; Li, D. Effect of Support on the Performance of Ni-Based Catalyst in Methane Dry Reforming. J. Fuel Chem. Technol. 2015, 43, 1359–1365.
  32. Gao, Y.; Aihemaiti, A.; Jiang, J.; Meng, Y.; Ju, T.; Han, S.; Chen, X.; Liu, J. Inspection over Carbon Deposition Features of Various Nickel Catalysts during Simulated Biogas Dry Reforming. J. Clean. Prod. 2020, 260, 120944.
  33. Min, J.; Lee, Y.; Park, H.; Zhang, C.; Jun, K. Carbon Dioxide Reforming of Methane on Ni–MgO–Al2O3 Catalysts Prepared by Sol–Gel Method: Effects of Mg/Al Ratios. J. Ind. Eng. Chem. 2015, 26, 375–383.
  34. Zhu, Y.; Zhang, S.; Chen, B.; Zhang, Z.; Shi, C. Effect of Mg/Al Ratio of NiMgAl Mixed Oxide Catalyst Derived from Hydrotalcite for Carbon Dioxide Reforming of Methane. Catal. Today 2016, 264, 163–170.
  35. Zhan, Y.; Han, J.; Bao, Z.; Cao, B.; Li, Y.; Street, J.; Yu, F. Biogas Reforming of Carbon Dioxide to Syngas Production over Ni-Mg-Al Catalysts. Mol. Catal. 2017, 436, 248–258.
  36. Ha, Q.; Armbruster, U.; Atia, H.; Schneider, M.; Lund, H.; Agostini, G.; Radnik, J.; Vuong, H.; Martin, A. Development of Active and Stable Low Nickel Content Catalysts for Dry Reforming of Methane. Catalysts 2017, 7, 157.
  37. Nguyen-Phu, H.; Kim, T.; Kim, Y.; Kang, K.H.; Cho, H.; Kim, J.; Ro, I. Role of Phase in NiMgAl Mixed Oxide Catalysts for CO2 Dry Methane Reforming (DRM). Catal. Today 2023, 411–412, 113894.
  38. Akbari, E.; Alavi, S.M.; Rezaei, M. Synthesis Gas Production over Highly Active and Stable Nanostructured Ni-MgO-Al2O3 Catalysts in Dry Reforming of Methane: Effects of Ni Contents. Fuel 2017, 194, 171–179.
  39. Alipour, Z.; Rezaei, M.; Meshkani, F. Effect of Alkaline Earth Promoters (MgO, CaO, and BaO) on the Activity and Coke Formation of Ni Catalysts Supported on Nanocrystalline Al2O3 in Dry Reforming of Methane. J. Ind. Eng. Chem. 2014, 20, 2858–2863.
  40. Sengupta, S.; Deo, G. Modifying Alumina with CaO or MgO in Supported Ni and Ni–Co Catalysts and Its Effect on Dry Reforming of CH4. J. CO2 Util. 2015, 10, 67–77.
  41. Charisiou, N.D.; Baklavaridis, A.; Papadakis, V.G.; Goula, M.A. Synthesis Gas Production via the Biogas Reforming Reaction Over Ni/MgO–Al2O3 and Ni/CaO–Al2O3 Catalysts. Waste Biomass Valorization 2016, 7, 725–736.
  42. Teh, L.P.; Setiabudi, H.D.; Timmiati, S.N.; Aziz, M.A.A.; Annuar, N.H.R.; Ruslan, N.N. Recent Progress in Ceria-Based Catalysts for the Dry Reforming of Methane: A Review. Chem. Eng. Sci. 2021, 242, 116606.
  43. Damyanova, S.; Pawelec, B.; Palcheva, R.; Karakirova, Y.; Sanchez, M.C.C.; Tyuliev, G.; Gaigneaux, E.; Fierro, J.L.G. Structure and Surface Properties of Ceria-Modified Ni-Based Catalysts for Hydrogen Production. Appl. Catal. B Environ. 2018, 225, 340–353.
  44. Li, M.; van Veen, A.C. Tuning the Catalytic Performance of Ni-Catalysed Dry Reforming of Methane and Carbon Deposition via Ni-CeO2- Interaction. Appl. Catal. B Environ. 2018, 237, 641–648.
  45. Lino, A.V.P.; Assaf, E.M.; Assaf, J.M. Hydrotalcites Derived Catalysts for Syngas Production from Biogas Reforming: Effect of Nickel and Cerium Load. Catal. Today 2017, 289, 78–88.
  46. Rosha, P.; Mohapatra, S.K.; Mahla, S.K.; Dhir, A. Biogas Reforming for Hydrogen Enrichment by Ceria Decorated over Nickel Catalyst Supported on Titania and Alumina. Int. J. Hydrogen Energy 2018, 43, 21246–21255.
  47. Luisetto, I.; Tuti, S.; Battocchio, C.; Lo Mastro, S.; Sodo, A. Ni/CeO2–Al2O3 Catalysts for the Dry Reforming of Methane: The Effect of CeAlO3 Content and Nickel Crystallite Size on Catalytic Activity and Coke Resistance. Appl. Catal. A Gen. 2015, 500, 12–22.
  48. Aghamohammadi, S.; Haghighi, M.; Maleki, M.; Rahemi, N. Sequential Impregnation vs. Sol-Gel Synthesized Ni/Al2O3-CeO2 Nanocatalyst for Dry Reforming of Methane: Effect of Synthesis Method and Support Promotion. Mol. Catal. 2017, 431, 39–48.
  49. Marinho, A.L.A.; Toniolo, F.S.; Noronha, F.B.; Epron, F.; Duprez, D.; Bion, N. Highly Active and Stable Ni Dispersed on Mesoporous CeO2-Al2O3 Catalysts for Production of Syngas by Dry Reforming of Methane. Appl. Catal. B Environ. 2021, 281, 119459.
  50. Yang, R.; Xing, C.; Lv, C.; Shi, L.; Tsubaki, N. Promotional Effect of La2O3 and CeO2 on Ni/γ-Al2O3 Catalysts for CO2 Reforming of CH4. Appl. Catal. A Gen. 2010, 385, 92–100.
  51. Charisiou, N.D.; Siakavelas, G.; Papageridis, K.N.; Baklavaridis, A.; Tzounis, L.; Avraam, D.G.; Goula, M.A. Syngas Production via the Biogas Dry Reforming Reaction over Nickel Supported on Modified with CeO2 and/or La2O3 Alumina Catalysts. J. Nat. Gas Sci. Eng. 2016, 31, 164–183.
  52. Farooqi, A.S.; Al-Swai, B.M.; Ruslan, F.H.; Mohd Zabidi, N.A.; Saidur, R.; Syed Muhammad, S.A.F.; Abdullah, B. Catalytic Conversion of Greenhouse Gases (CO2 and CH4) to Syngas over Ni-Based Catalyst: Effects of Ce-La Promoters. Arab. J. Chem. 2020, 13, 5740–5749.
  53. Taherian, Z.; Shahed Gharahshiran, V.; Khataee, A.; Meshkani, F.; Orooji, Y. Comparative Study of Modified Ni Catalysts over Mesoporous CaO-Al2O3 Support for CO2/Methane Reforming. Catal. Commun. 2020, 145, 106100.
  54. Shamskar, F.R.; Meshkani, F.; Rezaei, M. Preparation and Characterization of Ultrasound-Assisted Co-Precipitated Nanocrystalline La-, Ce-, Zr -Promoted Ni-Al2O3 Catalysts for Dry Reforming Reaction. J. CO2 Util. 2017, 22, 124–134.
  55. Rezaei, M.; Alavi, S.M. Dry Reforming over Mesoporous Nanocrystalline 5% Ni/M-MgAl2O4 (M: CeO2, ZrO2, La2O3) Catalysts. Int. J. Hydrogen Energy 2019, 44, 16516–16525.
  56. Calgaro, C.O.; Lima, D.d.S.; Tonietto, R.; Perez-Lopez, O.W. Biogas Dry Reforming Over Ni–Mg–La–Al Catalysts: Influence of La/Mg Ratio. Catal. Lett. 2021, 151, 267–280.
  57. Al-Mubaddel, F.S.; Kumar, R.; Sofiu, M.L.; Frusteri, F.; Ibrahim, A.A.; Srivastava, V.K.; Kasim, S.O.; Fakeeha, A.H.; Abasaeed, A.E.; Osman, A.I.; et al. Optimizing Acido-Basic Profile of Support in Ni Supported La2O3-Al2O3 Catalyst for Dry Reforming of Methane. Int. J. Hydrogen Energy 2021, 46, 14225–14235.
  58. Charisiou, N.D.; Tzounis, L.; Sebastian, V.; Hinder, S.J.; Baker, M.A.; Polychronopoulou, K.; Goula, M.A. Investigating the Correlation between Deactivation and the Carbon Deposited on the Surface of Ni/Al2O3 and Ni/La2O3-Al2O3 Catalysts during the Biogas Reforming Reaction. Appl. Surf. Sci. 2019, 474, 42–56.
  59. Al-Fatesh, A.S.; Naeem, M.A.; Fakeeha, A.H.; Abasaeed, A.E. Role of La2O3 as Promoter and Support in Ni/γ-Al2O3 Catalysts for Dry Reforming of Methane. Chin. J. Chem. Eng. 2014, 22, 28–37.
  60. Tsoukalou, A.; Imtiaz, Q.; Kim, S.M.; Abdala, P.M.; Yoon, S.; Müller, C.R. Dry-Reforming of Methane over Bimetallic Ni–M/La2O3 (M = Co, Fe): The Effect of the Rate of La2O2CO3 Formation and Phase Stability on the Catalytic Activity and Stability. J. Catal. 2016, 343, 208–214.
  61. Li, K.; Chang, X.; Pei, C.; Li, X.; Chen, S.; Zhang, X.; Assabumrungrat, S.; Zhao, Z.J.; Zeng, L.; Gong, J. Ordered Mesoporous Ni/La2O3 Catalysts with Interfacial Synergism towards CO2 Activation in Dry Reforming of Methane. Appl. Catal. B Environ. 2019, 259, 118092.
  62. Li, K.; Pei, C.; Li, X.; Chen, S.; Zhang, X.; Liu, R.; Gong, J. Dry Reforming of Methane over La2O2CO3-Modified Ni/Al2O3 Catalysts with Moderate Metal Support Interaction. Appl. Catal. B Environ. 2020, 264, 118448.
  63. Therdthianwong, S.; Siangchin, C.; Therdthianwong, A. Improvement of Coke Resistance of Ni/Al2O3 Catalyst in CH4/CO2 Reforming by ZrO2 Addition. Fuel Process. Technol. 2008, 89, 160–168.
  64. Morales Anzures, F.; Salinas Hernández, P.; Mondragón Galicia, G.; Gutiérrez Martínez, A.; Tzompantzi Morales, F.; Romero Romo, M.A.; Pérez Hernández, R. Synthetic Gas Production by Dry Reforming of Methane over Ni/Al2O3–ZrO2 Catalysts: High H2/CO Ratio. Int. J. Hydrogen Energy 2021, 46, 26224–26233.
  65. Shin, S.A.; Noh, Y.S.; Hong, G.H.; Park, J.I.; Song, H.T.; Lee, K.Y.; Moon, D.J. Dry Reforming of Methane over Ni/ZrO2-Al2O3 Catalysts: Effect of Preparation Methods. J. Taiwan Inst. Chem. Eng. 2018, 90, 25–32.
  66. Iglesias, I.; Baronetti, G.; Alemany, L.; Mariño, F. Insight into Ni/Ce1−xZrxO2−δ Support Interplay for Enhanced Methane Steam Reforming. Int. J. Hydrogen Energy 2019, 44, 3668–3680.
  67. Kumar, P.; Sun, Y.; Idem, R.O. Nickel-Based Ceria, Zirconia, and Ceria–Zirconia Catalytic Systems for Low-Temperature Carbon Dioxide Reforming of Methane. Energy Fuels 2007, 21, 3113–3123.
  68. Kambolis, A.; Matralis, H.; Trovarelli, A.; Papadopoulou, C. Ni/CeO2-ZrO2 Catalysts for the Dry Reforming of Methane. Appl. Catal. A Gen. 2010, 377, 16–26.
  69. Wolfbeisser, A.; Sophiphun, O.; Bernardi, J.; Wittayakun, J.; Föttinger, K.; Rupprechter, G. Methane Dry Reforming over Ceria-Zirconia Supported Ni Catalysts. Catal. Today 2016, 277, 234–245.
  70. Luisetto, I.; Tuti, S.; Romano, C.; Boaro, M.; Di Bartolomeo, E.; Kesavan, J.K.; Kumar, S.S.; Selvakumar, K. Dry Reforming of Methane over Ni Supported on Doped CeO2: New Insight on the Role of Dopants for CO2 Activation. J. CO2 Util. 2019, 30, 63–78.
  71. Zhang, X.; Zhang, Q.; Tsubaki, N.; Tan, Y.; Han, Y. Influence of Zirconia Phase on the Performance of Ni/ZrO2 for Carbon Dioxide Reforming of Methane. In Advances in CO2 Capture, Sequestration, and Conversion; Jin, F., He, L., Hu, Y., Eds.; ACS Symposium Series; American Chemical Society: Washington, DC, USA, 2015; Volume 1194, pp. 135–153.
  72. Zhang, X.; Zhang, Q.; Tsubaki, N.; Tan, Y.; Han, Y. Carbon Dioxide Reforming of Methane over Ni Nanoparticles Incorporated into Mesoporous Amorphous ZrO2 Matrix. Fuel 2015, 147, 243–252.
  73. Zhang, M.; Zhang, J.; Wu, Y.; Pan, J.; Zhang, Q.; Tan, Y.; Han, Y. Insight into the Effects of the Oxygen Species over Ni/ZrO2 Catalyst Surface on Methane Reforming with Carbon Dioxide. Appl. Catal. B Environ. 2019, 244, 427–437.
  74. Lou, Y.; Steib, M.; Zhang, Q.; Tiefenbacher, K.; Horváth, A.; Jentys, A.; Liu, Y.; Lercher, J.A. Design of Stable Ni/ZrO2 Catalysts for Dry Reforming of Methane. J. Catal. 2017, 356, 147–156.
  75. Goula, M.A.; Charisiou, N.D.; Siakavelas, G.; Tzounis, L.; Tsiaoussis, I.; Panagiotopoulou, P.; Goula, G.; Yentekakis, I.V. Syngas Production via the Biogas Dry Reforming Reaction over Ni Supported on Zirconia Modified with CeO2 or La2O3 Catalysts. Int. J. Hydrogen Energy 2017, 42, 13724–13740.
  76. Charisiou, N.D.; Siakavelas, G.; Tzounis, L.; Sebastian, V.; Monzon, A.; Baker, M.A.; Hinder, S.J.; Polychronopoulou, K.; Yentekakis, I.V.; Goula, M.A. An in Depth Investigation of Deactivation through Carbon Formation during the Biogas Dry Reforming Reaction for Ni Supported on Modified with CeO2 and La2O3 Zirconia Catalysts. Int. J. Hydrogen Energy 2018, 43, 18955–18976.
  77. Fakeeha, A.H.; Khan, W.U.; Al-Fatesh, A.S.; Abasaeed, A.E. Stabilities of Zeolite-Supported Ni Catalysts for Dry Reforming of Methane. Chin. J. Catal. 2013, 34, 764–768.
  78. Moradi, G.; Khezeli, F.; Hemmati, H. Syngas Production with Dry Reforming of Methane over Ni/ZSM-5 Catalysts. J. Nat. Gas Sci. Eng. 2016, 33, 657–665.
  79. Singh, S.; Kumar, R.; Setiabudi, H.D.; Nanda, S.; Vo, D.N. Advanced Synthesis Strategies of Mesoporous SBA-15 Supported Catalysts for Catalytic Reforming Applications: A State-of-the-Art Review. Appl. Catal. A Gen. 2018, 559, 57–74.
  80. Gálvez, M.E.; Albarazi, A.; Da Costa, P. Enhanced Catalytic Stability through Non-Conventional Synthesis of Ni/SBA-15 for Methane Dry Reforming at Low Temperatures. Appl. Catal. A Gen. 2015, 504, 143–150.
  81. Karam, L.; Casale, S.; El Zakhem, H.; El Hassan, N. Tuning the Properties of Nickel Nanoparticles inside SBA-15 Mesopores for Enhanced Stability in Methane Reforming. J. CO2 Util. 2017, 17, 119–124.
  82. Omoregbe, O.; Danh, H.T.; Nguyen-Huy, C.; Setiabudi, H.D.; Abidin, S.Z.; Truong, Q.D.; Vo, D.N. Syngas Production from Methane Dry Reforming over Ni/SBA-15 Catalyst: Effect of Operating Parameters. Int. J. Hydrogen Energy 2017, 42, 11283–11294.
  83. Kiani, P.; Meshksar, M.; Rahimpour, M.R. Biogas Reforming over La-Promoted Ni/SBA-16 Catalyst for Syngas Production: Catalytic Structure and Process Activity Investigation. Int. J. Hydrogen Energy 2023, 48, 6262–6274.
  84. Lovell, E.; Jiang, Y.; Scott, J.; Wang, F.; Suhardja, Y.; Chen, M.; Huang, J.; Amal, R. CO2 Reforming of Methane over MCM-41-Supported Nickel Catalysts: Altering Support Acidity by One-Pot Synthesis at Room Temperature. Appl. Catal. A Gen. 2014, 473, 51–58.
  85. Aguiar, M.; Cazula, B.B.; Saragiotto Colpini, L.M.; Borba, C.E.; Alves da Silva, F.; Noronha, F.B.; Alves, H.J. Si-MCM-41 Obtained from Different Sources of Silica and Its Application as Support for Nickel Catalysts Used in Dry Reforming of Methane. Int. J. Hydrogen Energy 2019, 44, 32003–32018.
  86. Zhang, Y.; Zhang, G.; Liu, J.; Li, T.; Wang, Y.; Zhao, Y.; Li, G.; Zhang, Y. Dry Reforming of Methane over Ni/SiO2 Catalysts: Role of Support Structure Properties. Fuel 2023, 340, 127490.
  87. Zhang, J.; Li, F. Coke-Resistant Ni@SiO2 Catalyst for Dry Reforming of Methane. Appl. Catal. B Environ. 2015, 176–177, 513–521.
  88. Wang, F.; Han, B.; Zhang, L.; Xu, L.; Yu, H.; Shi, W. CO2 Reforming with Methane over Small-Sized Ni@SiO2 Catalysts with Unique Features of Sintering-Free and Low Carbon. Appl. Catal. B Environ. 2018, 235, 26–35.
  89. Han, J.W.; Kim, C.; Park, J.S.; Lee, H. Highly Coke-Resistant Ni Nanoparticle Catalysts with Minimal Sintering in Dry Reforming of Methane. ChemSusChem 2014, 7, 451–456.
  90. Han, J.W.; Park, J.S.; Choi, M.S.; Lee, H. Uncoupling the Size and Support Effects of Ni Catalysts for Dry Reforming of Methane. Appl. Catal. B Environ. 2017, 203, 625–632.
  91. Das, S.; Ashok, J.; Bian, Z.; Dewangan, N.; Wai, M.H.; Du, Y.; Borgna, A.; Hidajat, K.; Kawi, S. Silica–Ceria Sandwiched Ni Core–Shell Catalyst for Low Temperature Dry Reforming of Biogas: Coke Resistance and Mechanistic Insights. Appl. Catal. B Environ. 2018, 230, 220–236.
  92. Han, K.; Xu, S.; Wang, Y.; Wang, S.; Zhao, L.; Kambonde, J.; Yu, H.; Shi, W.; Wang, F. Confining Ni and Ceria in Silica Shell as Synergistic Multifunctional Catalyst for Methane Dry Reforming Reaction. J. Power Sources 2021, 506, 230232.
  93. Lin, S.; Wang, J.; Mi, Y.; Yang, S.; Wang, Z.; Liu, W.; Wu, D.; Peng, H. Trifunctional Strategy for the Design and Synthesis of a Ni-CeO2@SiO2 Catalyst with Remarkable Low-Temperature Sintering and Coking Resistance for Methane Dry Reforming. Chin. J. Catal. 2021, 42, 1808–1820.
  94. Liu, W.; Li, L.; Zhang, X.; Wang, Z.; Wang, X.; Peng, H. Design of Ni-ZrO2@SiO2 Catalyst with Ultra-High Sintering and Coking Resistance for Dry Reforming of Methane to Prepare Syngas. J. CO2 Util. 2018, 27, 297–307.
  95. Das, S.; Jangam, A.; Jayaprakash, S.; Xi, S.; Hidajat, K.; Tomishige, K.; Kawi, S. Role of Lattice Oxygen in Methane Activation on Ni-Phyllosilicate@Ce1-XZrxO2 Core-Shell Catalyst for Methane Dry Reforming: Zr Doping Effect, Mechanism, and Kinetic Study. Appl. Catal. B Environ. 2021, 290, 119998.
  96. Marinho, A.L.A.; Rabelo-Neto, R.C.; Epron, F.; Bion, N.; Toniolo, F.S.; Noronha, F.B. Embedded Ni Nanoparticles in CeZrO2 as Stable Catalyst for Dry Reforming of Methane. Appl. Catal. B Environ. 2020, 268, 118387.
  97. Marinho, A.L.A.; Rabelo-Neto, R.C.; Epron, F.; Toniolo, F.S.; Noronha, F.B.; Bion, N. Effect of Metal Dopant on the Performance of Ni@CeMeO2 Embedded Catalysts (Me = Gd, Sm and Zr) for Dry Reforming of Methane. Methane 2022, 1, 300–319.
  98. Meloni, E.; Martino, M.; Palma, V. A Short Review on Ni Based Catalysts and Related Engineering Issues for Methane Steam Reforming. Catalysts 2020, 10, 352.
  99. Angeli, S.D.; Monteleone, G.; Giaconia, A.; Lemonidou, A.A. State-of-the-Art Catalysts for CH4 Steam Reforming at Low Temperature. Int. J. Hydrogen Energy 2014, 39, 1979–1997.
  100. Gao, X.; Ge, Z.; Zhu, G.; Wang, Z.; Ashok, J.; Kawi, S. Anti-Coking and Anti-Sintering Ni/Al2O3 Catalysts in the Dry Reforming of Methane: Recent Progress and Prospects. Catalysts 2021, 11, 1003.
  101. Zhang, J.; Wang, H.; Dalai, A.K. Development of Stable Bimetallic Catalysts for Carbon Dioxide Reforming of Methane. J. Catal. 2007, 249, 300–310.
  102. Kim, D.H.; Youn, J.R.; Seo, J.C.; Kim, S.B.; Kim, M.J.; Lee, K. One-Pot Synthesis of NiCo/MgAl2O4 Catalyst for High Coke-Resistance in Steam Methane Reforming: Optimization of Ni/Co Ratio. Catal. Today 2023, 411–412, 113910.
  103. Braga, A.H.; De Oliveira, D.C.; Taschin, A.R.; Santos, J.B.O.; Gallo, J.M.R.; Buen, J.M.C. Steam Reforming of Ethanol Using Ni-Co Catalysts Supported on MgAl2O4: Structural Study and Catalytic Properties at Different Temperatures. ACS Catal. 2021, 11, 2047–2061.
  104. Koh, A.C.W.; Chen, L.; Kee Leong, W.; Johnson, B.F.G.; Khimyak, T.; Lin, J. Hydrogen or Synthesis Gas Production via the Partial Oxidation of Methane over Supported Nickel-Cobalt Catalysts. Int. J. Hydrogen Energy 2007, 32, 725–730.
  105. Sheng, K.; Luan, D.; Jiang, H.; Zeng, F.; Wei, B.; Pang, F.; Ge, J. NixCoy Nanocatalyst Supported by ZrO2 Hollow Sphere for Dry Reforming of Methane: Synergetic Catalysis by Ni and Co in Alloy. ACS Appl. Mater. Interfaces 2019, 11, 24078–24087.
  106. Bahari, M.B.; Setiabudi, H.D.; Ainirazali, N.; Vo, D.V.N. A Short Review on Bimetallic Co-Based Catalysts for Carbon Dioxide Reforming of Methane. Mater. Today Proc. 2019, 42, 94–100.
  107. You, X.; Wang, X.; Ma, Y.; Liu, J.; Liu, W.; Xu, X.; Peng, H.; Li, C.; Zhou, W.; Yuan, P.; et al. Ni-Co/Al2O3 Bimetallic Catalysts for CH4 Steam Reforming: Elucidating the Role of Co for Improving Coke Resistance. ChemCatChem 2014, 6, 3377–3386.
  108. Horlyck, J.; Lawrey, C.; Lovell, E.C.; Amal, R.; Scott, J. Elucidating the Impact of Ni and Co Loading on the Selectivity of Bimetallic NiCo Catalysts for Dry Reforming of Methane. Chem. Eng. J. 2018, 352, 572–580.
  109. Lyu, L.; Shengene, M.; Ma, Q.; Sun, J.; Gao, X.; Fan, H.; Zhang, J.; Zhao, T.S. Synergy of Macro-Meso Bimodal Pore and Ni-Co Alloy for Enhanced Stability in Dry Reforming of Methane. Fuel 2022, 310, 122375.
  110. Zolghadri, S.; Honarvar, B.; Rahimpour, M.R. Synthesis, Application, and Characteristics of Mesoporous Alumina as a Support of Promoted Ni-Co Bimetallic Catalysts in Steam Reforming of Methane. Fuel 2023, 335, 127005.
  111. Sharifi, M.; Haghighi, M.; Rahmani, F.; Karimipour, S. Syngas Production via Dry Reforming of CH4 over Co- and Cu-Promoted Ni/Al2O3-ZrO2 Nanocatalysts Synthesized via Sequential Impregnation and Sol-Gel Methods. J. Nat. Gas Sci. Eng. 2014, 21, 993–1004.
  112. Bernardo, C.A.; Alstrup, I.; Rostrup-Nielsen, J.R. Carbon Deposition and Methane Steam Reforming on Silica-Supported NiCu Catalysts. J. Catal. 1985, 96, 517–534.
  113. Moradi, G.R.; Khosravian, F.; Rahmanzadeh, M. Effects of Partial Substitution of Ni by Cu in LaNiO3 Perovskite Catalyst for Dry Methane Reforming. Chin. J. Catal. 2012, 33, 797–801.
  114. Quirino, P.P.S.; Amaral, A.F.; Manenti, F.; Pontes, K.V. Mapping and Optimization of an Industrial Steam Methane Reformer by the Design of Experiments (DOE). Chem. Eng. Res. Des. 2022, 184, 349–365.
  115. Chatla, A.; Ghouri, M.M.; El Hassan, O.W.; Mohamed, N.; Prakash, A.V.; Elbashir, N.O. An Experimental and First Principles DFT Investigation on the Effect of Cu Addition to Ni/Al2O3 Catalyst for the Dry Reforming of Methane. Appl. Catal. A Gen. 2020, 602, 117699.
  116. Tavares, M.T.; Alstrup, I.; Bernardo, C.A.A. Coking and Decoking during Methanation and Methane Decomposition on Ni-Cu Supported Catalysts. Mater. Corros.—Werkst. Und Korros. 1999, 50, 681–685.
  117. La Rosa, D.; Lo Faro, M.; Monforte, G.; Antonucci, V.; Aricò, A.S.; Sin, A. Recent Advances on the Development of NiCu Alloy Catalysts for IT-SOFCs. ECS Trans. 2007, 7, 1685–1693.
  118. Kitla, A.; Safonova, O.V.; Föttinger, K. Infrared Studies on Bimetallic Copper/Nickel Catalysts Supported on Zirconia and Ceria/Zirconia. Catal. Lett. 2013, 143, 517–530.
  119. Naghash, A.R.; Etsell, T.H.; Xu, S. XRD and XPS Study of Cu-Ni Interactions on Reduced Copper-Nickel-Aluminum Oxide Solid Solution Catalysts. Chem. Mater. 2006, 18, 2480–2488.
  120. Song, K.; Lu, M.; Xu, S.; Chen, C.; Zhan, Y.; Li, D.; Au, C.; Jiang, L.; Tomishige, K. Effect of Alloy Composition on Catalytic Performance and Coke-Resistance Property of Ni-Cu/Mg(Al)O Catalysts for Dry Reforming of Methane. Appl. Catal. B Environ. 2018, 239, 324–333.
  121. Nataj, S.M.M.; Alavi, S.M.; Mazloom, G. Modeling and Optimization of Methane Dry Reforming over Ni–Cu/Al2O3 Catalyst Using Box–Behnken Design. J. Energy Chem. 2018, 27, 1475–1488.
  122. Lee, J.H.; Lee, E.G.; Joo, O.S.; Jung, K.D. Stabilization of Ni/Al2O3 Catalyst by Cu Addition for CO2 Reforming of Methane. Appl. Catal. A Gen. 2004, 269, 1–6.
  123. Han, K.; Wang, S.; Liu, Q.; Wang, F. Optimizing the Ni/Cu Ratio in Ni-Cu Nanoparticle Catalysts for Methane Dry Reforming. ACS Appl. Nano Mater. 2021, 4, 5340–5348.
  124. Braga, A.; Armengol-Profitós, M.; Pascua-Solé, L.; Vendrell, X.; Soler, L.; Serrano, I.; Villar-Garcia, I.J.; Pérez-Dieste, V.; Divins, N.J.; Llorca, J. Bimetallic NiFe Nanoparticles Supported on CeO2 as Catalysts for Methane Steam Reforming. ACS Appl. Nano Mater. 2023, 6, 7173–7185.
  125. Kim, S.M.; Abdala, P.M.; Margossian, T.; Hosseini, D.; Foppa, L.; Armutlulu, A.; Van Beek, W.; Comas-Vives, A.; Copéret, C.; Müller, C. Cooperativity and Dynamics Increase the Performance of NiFe Dry Reforming Catalysts. J. Am. Chem. Soc. 2017, 139, 1937–1949.
  126. Tomishige, K.; Li, D.; Tamura, M.; Nakagawa, Y. Nickel-Iron Alloy Catalysts for Reforming of Hydrocarbons: Preparation, Structure, and Catalytic Properties. Catal. Sci. Technol. 2017, 7, 3952–3979.
  127. Li, Y.; Wang, Q.; Cao, M.; Li, S.; Song, Z.; Qiu, L.; Yu, F.; Li, R.; Yan, X. Structural Evolution of Robust Ni3Fe1 Alloy on Al2O3 in Dry Reforming of Methane: Effect of Iron-Surplus Strategy from Ni1Fe1 to Ni3Fe1. Appl. Catal. B Environ. 2023, 331, 122669.
  128. Song, Z.; Wang, Q.; Guo, C.; Li, S.; Yan, W.; Jiao, W.; Qiu, L.; Yan, X.; Li, R. Improved Effect of Fe on the Stable NiFe/Al2O3 Catalyst in Low-Temperature Dry Reforming of Methane. Ind. Eng. Chem. Res. 2020, 59, 17250–17258.
  129. Thalinger, R.; Gocyla, M.; Heggen, M.; Dunin-Borkowski, R.; Grünbacher, M.; Stöger-Pollach, M.; Schmidmair, D.; Klötzer, B.; Penner, S. Ni-Perovskite Interaction and Its Structural and Catalytic Consequences in Methane Steam Reforming and Methanation Reactions. J. Catal. 2016, 337, 26–35.
  130. Kim, W.Y.; Jang, J.S.; Ra, E.C.; Kim, K.Y.; Kim, E.H.; Lee, J.S. Reduced Perovskite LaNiO3 Catalysts Modified with Co and Mn for Low Coke Formation in Dry Reforming of Methane. Appl. Catal. A Gen. 2019, 575, 198–203.
  131. García-Diéguez, M.; Pieta, I.S.; Herrera, M.C.; Larrubia, M.A.; Alemany, L.J. Improved Pt-Ni Nanocatalysts for Dry Reforming of Methane. Appl. Catal. A Gen. 2010, 377, 191–199.
  132. Rostrup-Nielsen, J.R. Promotion by Poisoning. Stud. Surf. Sci. Catal. 1991, 68, 85–101.
  133. Pawelec, B.; Damyanova, S.; Arishtirova, K.; Fierro, J.L.G.; Petrov, L. Structural and Surface Features of PtNi Catalysts for Reforming of Methane with CO2. Appl. Catal. A Gen. 2007, 323, 188–201.
  134. Dai, C.; Zhang, S.; Zhang, A.; Song, C.; Shi, C.; Guo, X. Hollow Zeolite Encapsulated Ni-Pt Bimetals for Sintering and Coking Resistant Dry Reforming of Methane. J. Mater. Chem. A 2015, 3, 16461–16468.
  135. García-Diéguez, M.; Finocchio, E.; Larrubia, M.Á.; Alemany, L.J.; Busca, G. Characterization of Alumina-Supported Pt, Ni and PtNi Alloy Catalysts for the Dry Reforming of Methane. J. Catal. 2010, 274, 11–20.
  136. García-Diéguez, M.; Pieta, I.S.; Herrera, M.C.; Larrubia, M.A.; Alemany, L.J. Nanostructured Pt- and Ni-Based Catalysts for CO2-Reforming of Methane. J. Catal. 2010, 270, 136–145.
  137. Egelske, B.T.; Keels, J.M.; Monnier, J.R.; Regalbuto, J.R. An Analysis of Electroless Deposition Derived Ni-Pt Catalysts for the Dry Reforming of Methane. J. Catal. 2020, 381, 374–384.
  138. Wang, J.; Mao, Y.; Zhang, L.Z.; Li, Y.; Liu, W.; Ma, Q.; Wu, D.; Peng, H. Remarkable Basic-Metal Oxides Promoted Confinement Catalysts for CO2 Reforming. Fuel 2022, 315, 123167.
  139. Mao, Y.; Zhang, L.; Zheng, X.; Liu, W.; Cao, Z.; Peng, H. Coke-Resistance over Rh–Ni Bimetallic Catalyst for Low Temperature Dry Reforming of Methane. Int. J. Hydrogen Energy 2023, 48, 13890–13901.
  140. Jóźwiak, W.K.; Nowosielska, M.; Rynkowski, J. Reforming of Methane with Carbon Dioxide over Supported Bimetallic Catalysts Containing Ni and Noble Metal I. Characterization and Activity of SiO2 Supported Ni-Rh Catalysts. Appl. Catal. A Gen. 2005, 280, 233–244.
  141. Romano, P.N.; de Carvalho Filho, J.F.S.; de Almeida, J.M.A.R.; Sousa-Aguiar, E.F. Screening of Mono and Bimetallic Catalysts for the Dry Reforming of Methane. Catal. Today 2022, 394–396, 348–356.
  142. Steinhauer, B.; Kasireddy, M.R.; Radnik, J.; Martin, A. Development of Ni-Pd Bimetallic Catalysts for the Utilization of Carbon Dioxide and Methane by Dry Reforming. Appl. Catal. A Gen. 2009, 366, 333–341.
  143. Ma, Q.; Sun, J.; Gao, X.; Zhang, J.; Zhao, T.; Yoneyama, Y.; Tsubaki, N. Ordered Mesoporous Alumina-Supported Bimetallic Pd-Ni Catalysts for Methane Dry Reforming Reaction. Catal. Sci. Technol. 2016, 6, 6542–6550.
More
© Text is available under the terms and conditions of the Creative Commons Attribution (CC BY) license; additional terms may apply. By using this site, you agree to the Terms and Conditions and Privacy Policy.
Upload a video for this entry
Information
Subjects: Engineering, Chemical
Contributors MDPI registered users' name will be linked to their SciProfiles pages. To register with us, please refer to https://encyclopedia.pub/register :
Robinson L. Manfro
,
Mariana M. V. M. Souza
View Times: 446
Revisions: 2 times (View History)
Update Date: 21 Sep 2023
Table of Contents
Academic Video Service
Feedback