Jet Engine Thrust
Edit

The familiar explanation for jet thrust is a "black box" description which only looks at what goes into the jet engine, air and fuel, and what comes out, exhaust gas and an unbalanced force. This force, called thrust, is the sum of the momentum difference between entry and exit and any unbalanced pressure force between entry and exit, as explained in "Thrust calculation". As an example, an early turbojet, the Bristol Olympus Mk. 101, had a momentum thrust of 9300 lb. and a pressure thrust of 1800 lb. giving a total of 11,100 lb. Looking inside the "black box" shows that the thrust results from all the unbalanced momentum and pressure forces created within the engine itself. These forces, some forwards and some rearwards, are across all the internal parts, both stationary and rotating, such as ducts, compressors, etc., which are in the primary gas flow which flows through the engine from front to rear. The algebraic sum of all these forces is delivered to the airframe for propulsion. "Flight" gives examples of these internal forces for two early jet engines, the Rolls-Royce Avon Ra.14 and the de Havilland Goblin

jet thrust flight rolls-royce

1. Transferring Thrust to the Aircraft

The engine thrust acts along the engine centreline. The aircraft "holds" the engine on the outer casing of the engine at some distance from the engine centreline (at the engine mounts). This arrangement causes the engine casing to bend (known as backbone bending) and the round rotor casings to distort (ovalization). Distortion of the engine structure has to be controlled with suitable mount locations to maintain acceptable rotor and seal clearances and prevent rubbing. A well-publicized example of excessive structural deformation occurred with the original Pratt & Whitney JT9D engine installation in the Boeing 747 aircraft.[1] The engine mounting arrangement had to be revised with the addition of an extra thrust frame to reduce the casing deflections to an acceptable amount.[2][3]

2. Rotor Thrust

The rotor thrust on a thrust bearing is not related to the engine thrust. It may even change direction at some RPM. The bearing load is determined by bearing life considerations. Although the aerodynamic loads on the compressor and turbine blades contribute to the rotor thrust they are small compared to cavity loads inside the rotor which result from the secondary air system pressures and sealing diameters on discs, etc. To keep the load within the bearing specification seal diameters are chosen accordingly as, many years ago, on the backface of the impeller[4] in the de Havilland Ghost engine. Sometimes an extra disc known as a balance piston has to be added inside the rotor. An early turbojet example with a balance piston[5] was the Rolls-Royce Avon.

3. Thrust Calculation

The net thrust (FN) of an engine is given by:[6]:p16

FN=(m˙air+m˙fuel)vem˙airv
where:  
 air = the mass rate of air flow through the engine
 fuel = the mass rate of propellant flow entering the engine
ve = the effective exhaust velocity of the jet (the speed of the exhaust plume relative to the aircraft)
v = the velocity of the air intake = the true airspeed of the aircraft
( air +  fuel)ve = the nozzle gross thrust (FG)
 air v = the ram drag of the intake air

Most types of jet engine have an air intake, which provides the bulk of the fluid exiting the exhaust. Conventional rocket engines, however, do not have an intake, so  air is zero. Therefore, rocket engines do not have ram drag and the gross thrust of the rocket engine nozzle is the net thrust of the engine. Consequently, the thrust characteristics of a rocket motor are different from that of an air breathing jet engine, and thrust is independent of velocity.

If the velocity of the jet from a jet engine is equal to sonic velocity, the jet engine's nozzle is said to be choked. If the nozzle is choked, the pressure at the nozzle exit plane is greater than atmospheric pressure, and extra terms must be added to the above equation to account for the pressure thrust.[6]

The rate of flow of fuel entering the engine is often very small compared with the rate of flow of air.[6] When the contribution of fuel to the nozzle gross thrust can be ignored, the net thrust is:

FN=m˙air(vev)

The velocity of the jet (ve) must exceed the true airspeed of the aircraft (v) if there is to be a net forward thrust on the aircraft. The velocity (ve) can be calculated thermodynamically based on adiabatic expansion.[7]

4. Thrust Augmentation

Thrust augmentation has taken many forms, most commonly to supplement inadequate take-off thrust. Some early jet aircraft needed rocket assistance to take off from high altitude airfields or when the day temperature was high. A more recent aircraft, the Tupolev Tu-22 supersonic bomber, was fitted with four SPRD-63 boosters for take-off.[8] Possibly the most extreme requirement needing rocket assistance, and which was short-lived, was zero-length launching. Almost as extreme, but very common, is catapult assistance from aircraft carriers. Rocket assistance has also been used during flight. The SEPR 841 booster engine was used on the Dassault Mirage for high altitude interception.[9]

Early aft-fan arrangements which added bypass airflow to a turbojet were known as thrust augmentors.[10] The aft-fan fitted to the General Electric CJ805-3 turbojet augmented the take-off thrust from 11,650lb to 16,100lb.

Water, or other coolant,[11] injection into the compressor or combustion chamber and fuel injection into the jetpipe (afterburning/reheat) became standard ways to increase thrust, known as 'wet' thrust to differentiate with the no-augmentation 'dry' thrust.

Coolant injection (pre-compressor cooling) has been used, together with afterburning, to increase thrust at supersonic speeds. The 'Skyburner' McDonnell Douglas F-4 Phantom II set a world speed record using water injection in front of the engine.[12]

At high Mach numbers afterburners supply progressively more of the engine thrust as the thrust from the turbomachine drops off towards zero at which speed the engine pressure ratio (epr) has fallen to 1.0 and all the engine thrust comes from the afterburner. The afterburner also has to make up for the pressure loss across the turbomachine which is a drag item at higher speeds where the epr will be less than 1.0.[13][14]

Thrust augmentation of existing afterburning engine installations for special short-duration tasks has been the subject of studies for launching small payloads into low earth orbits using aircraft such as McDonnell Douglas F-4 Phantom II, McDonnell Douglas F-15 Eagle, Dassault Rafale and Mikoyan MiG-31,[15] and also for carrying experimental packages to high altitudes using a Lockheed SR-71.[16] In the first case an increase in the existing maximum speed capability is required for orbital launches. In the second case an increase in thrust within the existing speed capability is required. Compressor inlet cooling is used in the first case. A compressor map shows that the airflow reduces with increasing compressor inlet temperature although the compressor is still running at maximum RPM (but reduced aerodynamic speed). Compressor inlet cooling increases the aerodynamic speed and flow and thrust. In the second case a small increase in the maximum mechanical speed and turbine temperature were allowed, together with nitrous oxide injection into the afterburner and simultaneous increase in afterburner fuel flow.

References

  1. "1969 - 3201 - Flight Archive". https://www.flightglobal.com/pdfarchive/view/1969/1969%20-%203201.html. ;
  2. "Jet engine force frame". http://www.google.com/patents/US3675418. ;
  3. "747 Creating the world's first jumbo jet and other adventures from a life in aviation" Joe Sutter, Smithsonian Books, ISBN:978-0-06-088241-9, p.185-188
  4. "de havilland - 1947 - 0202 - Flight Archive". https://www.flightglobal.com/pdfarchive/view/1947/1947%20-%200202.html. ;
  5. "rolls-royce avon - 1955 - 1778 - Flight Archive". https://www.flightglobal.com/pdfarchive/view/1955/1955%20-%201778.html. ;
  6. Nicholas Cumpsty (2003). Jet Propulsion (2nd ed.). Cambridge University Press. ISBN 978-0-521-54144-2. 
  7. 16.Unified: Thermodynamics and Propulsion, Prof. Z. S. Spakovszky. Scroll down to "Performance of Turbojet Engines, Section 11.6.4. (Obtained from the website of the Massachusetts Institute of Technology) http://web.mit.edu/16.unified/www/SPRING/propulsion/notes/node139.html
  8. "Tupolev Tu-22 Blinder" Sergey Burdin & Alan E Dawes 2006, Pen & Sword Aviation, ISBN:1 84415 241 3, p.130
  9. "atar - snecma - pressure ratio - 1960 - 0376 - Flight Archive". https://www.flightglobal.com/pdfarchive/view/1960/1960%20-%200376.html. ;
  10. Gas turbine aero-thermodynamics : with special reference to aircraft propulsion Sir Frank Whittle, Pergamon Press Ltd. 1981, ISBN:9780080267197. p.220
  11. "gas turbines - flight boosting - boosting gas - 1952 - 0092 - Flight Archive". https://www.flightglobal.com/pdfarchive/view/1952/1952%20-%200092.html. ;
  12. "Flightdeck Friday: The YF4H-1 Phantom II – Operations Skyburner and Sageburner". http://steeljawscribe.com/2007/03/23/flightdeck-friday-the-yf4h-1-phantom-ii-operations-skyburner-and-sageburner. ;
  13. "Jet Propulsion For Aerospace Applications" Second Edition 1964, Hesse and Mumford, Pitman Publishing Corporation, Library of Congress Catalog Card Number 64-18757, p.375
  14. "F-12 Series Aircraft Propulsion System Performance and Development, David H. Campbell, J. Aircraft Vol.II, No.11, November 1974, p.672
  15. "Water injection pre-compressor cooling assist space access" Mehta, Huynh, Hagseth, The Aeronautical Journal, February 2015, Volume 19, Number 1212, p.147
  16. "Data" (PDF). https://ntrs.nasa.gov/archive/nasa/casi.ntrs.nasa.gov/19970019923.pdf. ;
More
Related Content
Limaçon rotary machines are the heart of power generation systems, especially small- and micro-scale ones. These machines are the prime movers that play the main role in converting the potential energy to other useful forms of work, such as mechanical and/or electrical; the generated energy can also be stored in batteries or in the form of hydrogen. The focus of this paper is on the working of this limaçon technology, and the embodiments and mechanical drives to produce the unique motion of these machines. This paper will also discuss the related power-generating cycles and control schemes.
Keywords: power generation cycles; rotary machine; prime mover; expander; limaçon technology; control system
This thesis presents a comprehensive exploration into the design, modeling, and analysis of a wind turbine, employing a multidisciplinary approach to optimize its performance. The blade geometry was generated using QBlade software, a robust tool for blade design in wind turbine applications. The 3D model was then meticulously crafted using SolidWorks, integrating aerodynamic principles and structural considerations. The heart of this project lies in the utilization of SolidWorks Flow Simulation for a detailed analysis of the aerodynamic characteristics of the designed wind turbine. The simulation facilitated a thorough examination of airflow patterns, turbulence effects, and pressure distributions around the blades, offering valuable insights into the efficiency and energy-capturing potential of the turbine under various wind conditions.
Keywords: Wind Turbine; Design; Simulation; QBlade: SolidWorks; CFD; Flow Simulation; NACA4412, Renewable Ener
Wind farm layout optimization is crucial for maximizing energy production in renewable energy systems. This video introduces a novel layout optimization method for offshore wind farms that aims to minimize power deficits caused by the wake effect, without restrictions on the number of turbines, their shape, or the extent of the concession area. The core of this algorithm is a gradient descent method, which progressively and randomly incorporates new turbines into the concession area. As the optimization process unfolds, the turbines expand outward, seeking areas with less perturbation while pushing previous ones aside. To avoid local maxima at the end of the optimization process, the algorithm suppresses locations that contribute the most to potential power deficits. A comprehensive map of potential for the entire area is then generated, and a greedy algorithm places new turbines to finalize the layout. Remarkably, this entire process is completed in just 25 seconds. To significantly accelerate the search process and the creation of the potential map, a validated simplification is introduced: for turbines affected by multiple wakes, the power output is calculated using a linear aggregation of power deficits rather than the traditional linear or quadratic aggregation of speed deficits. This approach draws an analogy between power deficit and repulsive non-isotropic electrostatic potential energy, allowing the utilization of conservative field properties. As a result, this method is 20 times faster than any other layout optimization algorithm currently available in the literature. Additionally, irregular concession areas are effectively managed using Stokes’ theorem to identify outer points.
Keywords: layout optimization; offshore wind farm; gradient descent; greedy repositioning; power deficit; deficit aggregation; computation time
Have you ever dreamed of traveling to space? Well, one man not only shares that dream—he's determined to make it a reality: Elon Musk! Born in South Africa in 1971, he was a curious child who created and sold a video game called Blastar at just 12! Fast forward to the late '90s—Musk co-founded Zip2 and X.com, which morphed into PayPal. Instead of kicking back, he launched SpaceX in 2002 with dreams of making life multiplanetary. In 2003, he shook up the auto industry with Tesla, proving electric cars could be thrilling. But wait—there’s more! He dove into solar energy with SolarCity and even pitched the Hyperloop for speedy city travel. From electric cars to Mars, he challenges the impossible—reminding us that the future is what we make it!
Keywords: Elon Musk; SpaceX; Tesla; Hyperloop
Smoking is one of the leading preventable causes of disease and early death worldwide. Research from University College London reveals that the average loss of life per cigarette smoked, which is approximately 20 minutes: 17 for men and 22 for women. In 2000, the BMJ published a study estimated that each cigarette smoked in Britain shortens a smoker's life by about 11 minutes. But new research tells a different story! Updated data shows that smokers could actually lose 20 minutes of life expectancy for every cigarette—17 minutes for men and 22 minutes for women. So, what's changed? Well, smoking rates have dropped, but many smokers might actually be inhaling more deeply to get that same fix. Even though fewer cigarettes are being smoked, the health risks remain high. Here's a shocking takeaway: If you smoke 10 cigarettes a day but decide to quit on the 1st of January 2025, you could save a full day of life by January 8th, a week by February 20th, and even 50 days by the end of the year! The impact of smoking isn't just about the years lost, it also affects your health in those years. Smokers often feel like they age faster—imagine a 60-year-old smoker having the health of a 70-year-old non-smoker. But it's not all doom and gloom! Quitting at any age is beneficial, and the sooner you stop, the healthier you'll be. Remember, reducing your smoking isn't enough, the best choice is total cessation to maximize your health benefits.
Keywords: cigarette; smoking; life expectancy
Information
Contributor MDPI registered users' name will be linked to their SciProfiles pages. To register with us, please refer to https://encyclopedia.pub/register :
View Times: 13.0K
Entry Collection: HandWiki
Revision: 1 time (View History)
Update Date: 23 Nov 2022
Video Production Service