Submitted Successfully!
To reward your contribution, here is a gift for you: A free trial for our video production service.
Thank you for your contribution! You can also upload a video entry or images related to this topic.
Version Summary Created by Modification Content Size Created at Operation
1 + 3064 word(s) 3064 2021-08-03 05:04:28 |
2 format corrected. + 653 word(s) 3717 2021-08-05 04:33:17 | |
3 format corrected. + 788 word(s) 3852 2021-08-05 04:34:58 |

Video Upload Options

Do you have a full video?


Are you sure to Delete?
If you have any further questions, please contact Encyclopedia Editorial Office.
Vatin, N.I. Fly Ash-Based Eco-Efficient Concretes. Encyclopedia. Available online: (accessed on 18 June 2024).
Vatin NI. Fly Ash-Based Eco-Efficient Concretes. Encyclopedia. Available at: Accessed June 18, 2024.
Vatin, Nikolai Ivanovich. "Fly Ash-Based Eco-Efficient Concretes" Encyclopedia, (accessed June 18, 2024).
Vatin, N.I. (2021, August 04). Fly Ash-Based Eco-Efficient Concretes. In Encyclopedia.
Vatin, Nikolai Ivanovich. "Fly Ash-Based Eco-Efficient Concretes." Encyclopedia. Web. 04 August, 2021.
Fly Ash-Based Eco-Efficient Concretes

Concrete as a construction material is extensively used in the construction industry, with global annual consumption of approximately 25 billion cubic meters. Such high usage is due to the concrete’s low cost, excellent durability, readily availability of the constituent materials, and capability to be molded into different shapes. Among different constituents of concrete, binder materials are highly important for development of hydration in the microstructure of the concrete.

alkali-activated material fly ash short-term strengths pozzolanic properties utilizations

1. Introduction

Typically, cement is utilized as a binder in the formation of concrete [1]. It was reported that about 1 ton of CO 2 is released to the atmosphere for the production of one ton of OPC. It was also reported that annually OPC production releases about 1.5 billion tons of CO 2 globally, which is corresponding to about 9% of the worldwide total CO 2 emission globally [2][3][4]. For resolving this global environmental issue of cement production, numerous studies have been performed to find out a sustainable and eco-friendly supplementary cementitious material (SCM) as an alternative to cement in concrete production [5][6][7].

Among different SCMs used in concrete production, fly ash (FA) an industrial by-product of mineral coal burning made up from fine fuel particles found from flue gases and coal-fired boilers, and it can be employed as an SCM to minimize cement usage in concrete for lowering CO 2 emissions [5][8][9][10][11][12]. It was reported that more than about 544 million tons of FA are produced annually around the world and 80% of them are discarded in landfill. Moreover, FA has been well known as an eco-friendly material because its utilization reduces carbon footprint of cement production ( Figure 1 ). Using FA at very high content in self-consolidating concrete and high-performance concrete remained limited and further research on the topic is highly needed. Recently, substantial effort has been exerted to develop eco-efficient cement concrete composites [13][14]. FA is called pulverized fuel ash in the UK [15]. The hopper from where the FAs are collected affects their properties, and stockiest interviews showed that the cost of FAs had been already increased by 85–100% in 2012–2016 due to less availability of FA [16]. Despite that, over 6.6 × 10 7 and 11.1 × 10 7 tons of FA are generated due to coal-burning for electric power production in the United States and India every year (for example, occupying 26,304 hectares of land in India), respectively. Most FA ends up in landfill or surface impoundments as solid waste, and adequate disposal has been becoming a severe problem. Endeavors to reuse FA wastes were moderately successful, with only about 42% of FA waste being reduced [17][18][19]. Under such a condition, utilizing FA in green application technologies is necessary.

Figure 1. Potential percentage utilization of FA [23]. Reprinted with permission from Elsevier [23].

Recently, substantial efforts have been performed to improve the manufacturing of sustainable cement and the performance of FA-based alkali-activated material (AAM) [13][14]. FA is commonly employed as a pozzolanic material. It is also often employed as OPC’s partial or whole replacement material in concrete production [20]. Endeavors to reuse FA squanders were relatively successful, with about 70% of the total waste being reduced [17][18]. Figure 2 shows the worldwide production and utilization of FA [21]. FA together with other pozzolans is broadly approved by many design codes for utilization as an SCM in concrete, with an FA content of about 55%, according to CEM IV in BS EN 197 [22]. In recent years, researchers have assessed the probability of mixing diverse sorts of wastes with FA [23][24][25][26][27].

Figure 2. Production and utilization of FA globally (CFA: classified FA) [23]. Reprinted with permission from Elsevier [23].

In many nations, the construction sector demands an increase in the production of SCMs, like FA, because of their role in dropping the CO 2 emissions caused by cement production. Focus has turned to produce eco-friendly concrete that utilizes by-product materials such as FA ( Figure 3 ) [28][29][30]. An eco-efficient concrete is developed with the use of FA with numerous advantages, which as early strength gaining, low utilization of natural resources, and the ability to configure into different structural elements and to stay flawless for expanded periods without fix works. Therefore, the manufacturing of eco-friendly and economical concrete composite by waste materials received significant interest all around the world. Furthermore, this study presents a review of the classifications, sources, chemical composition, production techniques, curing regimes, and clean production of FA. Subsequently, physical, fresh, and mechanical properties of FA-based concrete are investigated. The aim of this study is to help in better understanding of the behavior of FA-based concrete as a sustainable and eco-friendly material used in construction and building industries.

Figure 3. Main constituents of FA and their applications (modified with improvements from Danish [31]).

2. Typical Curing Regimes of Fly Ash-Based Concrete

The typical curing regimes (water and steam curing) are given in detail in this section to help understanding the impact of curing on the hardened state of FA-based concrete.

Curing protects concrete from evaporation, temperature extremes, and the negative influence of cement hydration [31]. Fresh concrete must have adequate water content for hydration process to gain potential strength, improve durability performance, and maintain chemical reactions at a rapid and continuous rate [32]. After concrete casting, each test specimen must be stored in the casting room at approximately 30 °C to be later demolded after 24 h for water curing [33]. In water curing, sufficient time is given and the concrete gains its strength rapidly between 3 and 7 days; thereby, achieving the desired strength prescribed in design codes [34]. Curing time and temperature are the most influential factors in FA-based AAM’s compressive strength. However, Adam [35] stated that AAM could solidify quickly at room temperature and exhibited compressive strength of at least 20 MPa after 4.5 h at 20 °C and approximately 70–100 MPa after 28 days. A group of researchers performed tests on AAM mortars and found that the maximum strength of FA-based AAM is achieved in the first two days of curing [36]. Reportedly, elevated temperature curing enhances the strength by removing water from the FA-based AAM; thereby, initiating the failure of capillary pores in a dense structure [37]. FA-based AAM could be remedied at room temperature, but its strength grows gradually and continuously, and thereby, requires extended curing time [38]. Nasvi et al. [39] discovered that the crack initiation thresholds and crack closure of FA-based AAM cured at high temperatures (60 °C–80 °C) were higher (30–60%) than those remedied at air temperature (23 °C and 40 °C). Nonetheless, sustained curing at elevated temperatures disrupted AAMs’ rough composition, causing dehydration and extreme shrinkage and lowering the desired strength [40].

Steam curing is a standard heating method by transmitting heat to the FA-based AAM paste through steam. The heating varies and requires an extended time to achieve the desired temperature. Microwave heating depends on the inner energy debauchery related to molecular dipoles excitation in electromagnetic fields and conveys quick and constant heat [41]. In steam curing, concrete is permitted to dry in the air with strength of about 50% of that of moist-cured concrete after water curing for 28 days from casting [31][32][33]. The test can be performed in line with BS 1881: Part 110 [42]. The AAM that is cured in the absence of high heat can be utilized in other areas beyond precast members [43]. Manesh et al. [44] prepared FA-based AAM pastes with sodium silicate ( Na 2SiO 3) solution and 10 mol/L sodium hydroxide (NaOH) remedied for 5 min below 90 W microwave radiation by further heating at 65 °C (6 h), and compared the compressive strength with FA-based AAM cured at 65 °C (24 h). Radiation of microwave creates dense microstructure, accelerates the FA dissolution in an alkali solution, and reduces the curing time [45]. Moreover, AAM can attain higher compressive strengths through oven curing compared to that of ambient curing [46].

3. Mechanical Properties

Table 1 presents the field measurement data of concrete produced with OPC and FA. The strength of FA-based AAM depends on curing condition, Si/Al ratio, alkali solution, calcium content, and various additives [2][47][48]. As FA initially reacts with liquid at a reasonably slow rate, the compressive strength of the concrete at the first few days after mixing is low; however, high strength is developed at the longer ages [49][50]. The size of the FA particles is important for the strength development of concrete. In long periods, the strength increases with FA up to a replacement rate of about 25–35%, after which the strength starts to decrease with more added FA. Generally, class C FA is used within 15–40% of the total binder of concrete. Class C FAs improves the strength if the replacement level is restricted to 25% by the mass of the binder.

Table 1. Review on field measurement data of concrete produced with cement and FA.
Structural Element Age (Days) Exposure/
Service Situation
Concrete Compressive Strength (MPa) Cover (mm) Carbonation Footnotes Ref.
Depth (mm) Rate (mm/Year)
OPC:FA w/c Design In-Situ
Slab-on-grade 28 Industrial 100:0
Cube: 57·0
Cube: 49·0
Cube: 57·0
Slight corrosion found in FA concrete [220,221]
Foundation 25 - 100:0 0·52 21 Cube: 66·5 - - - [222]
Dam monolith 25 Base 5 ft (1·5 m) above high 80:20
Core: 36·5
Core: 28·0
- 0
Outfall canal–
20 water level
Core: 50·5
Core: 38·5
Insignificant cracks in both
concretes; no corrosion
10 Sheltered 100:0
Cube: 64·0
Cube: 81·5
- 1·1
Calcium hydroxide of FA concrete considerably lower than PC concrete  
Bridge—leaf pier 10 Sheltered 100:0
Cube: 47·0
Cube: 70·5
- 2·9
Buttress dam 30 - 100:0
Core: 42·5
Core: 48·0
- 5·0
Sea wall (land-ward side) 30 - 100:0
Core: 59·0
Core: 63·5
- 0·5
Foundation block 33 Interiorly
exposed, warm and dry
Core: 41·0
- 19·5

As well as its brittle nature, concrete is well known for its weakness in tension. The splitting tensile strength of FA-based AAMs can be enhanced using additives, such as sweet sorghum fibers and polyvinyl alcohol (PVA) fibers together with N-carboxymethyl chitosan [51]. A group of researchers made AAM with FA and alkali-pretreated sweet sorghum fibers that were acquired from the wastage of bagasse after removing the juice from the sweet sorghum stubbles for ethanol production [52]. They reported that when the percentage of sweet sorghum fibers was 2%, the tensile strength of the AAM increased by almost 36% [52]. Adding fibers to the mixture by a certain percentage limited the increase of micro-cracks, improving the tensile strength. However, the additional increase in fiber content led to the fiber agglomeration, resulting in a rise in air foams tricked in the mixture and non-uniform fiber distribution, and decreased tensile strength. Adding cotton to an FA-based AAM exhibited a similar trend for tensile strength [53]. It was reported that the increase in the tensile strength of chitosan- and fiber-reinforced FA-based AAM was mainly due to macro-and micro-fibers that could improve hydrogen bonds, load transfer, and fiber bridge action, and reduce the micro-cracks growth and expansion.

The flexural strength of FA-based concrete is considerably improved by integrating various kinds of short artificial fibers, such as polypropylene and PVA, through a linking influence during the macro-and micro-cracking of the AAM matrix under bending. The fibers for strengthening FA-based AAM composites include PVA fiber [54], steel fiber [1][55], sweet sorghum fiber [52], and cotton fiber [56][57]. FA-based AAMs can undergo stiff failure with small tensile strength and fracture toughness [51]. To obtain a great flexural strength, 2% of PVA fiber, 2% of steel fiber, and a hybrid combination of 1% of PVA and 1% of steel fiber were added. Besides, some studies showed the deflection toughening performance of the hybrid fiber-reinforced FA and reported that the flexural and bond strengths between the AAM matrix and PVA fiber were greater than those with cement paste matrix. The AAM matrix’s alkalinity shows no influence in the degradation of steel and PVA fibers [51]. Furthermore, cotton fabric layers were also included in the FA-based AAM composite to increase the flexural strength of the composite [56][57]. The improved flexural strength was exhibited in FA-based AAM in the range of 8.2 and 31.7 MPa, while the cotton fiber content was raised from 0 to 8.3%. Furthermore, FA’s flexural strength is disturbed by the alignment of cotton fabric layers [51]. The great flexural strength of FA-based concrete reinforced with cotton fabric placed horizontally can be accredited to the enhanced load dispersal consistency within the successive cotton fabric layers. The AAM with a vertical fabric alignment endured delamination and detachments between the AAM matrix and the cotton fabric, and had a less flexural strength [57].

It has been demonstrated that the modulus of elasticity and compressive strength of FA concrete are strongly correlated [58][59]. Generally, using FA in concrete increases the elastic modulus of concrete given the FA’s pozzolanic action over the concrete’ hydration period [60]. The low modulus of FA-based concrete is attributed to the low early strength development of the concrete [61]. AAMs with the average density of 2350 kg/m 3 have a higher elastic modulus than those containing OPC [62].

4. Heat of Hydration

The heat evolution upon complete hydration of a particular amount of unhydrated cement at a given temperature is a property of FA-based concrete ( Table 2 ) [2]. The total volume of free heat and the quantities of heat delivered by a single hydrating compound can be considered as reactivity indicators. Besides, heat of hydration exemplifies the settling and toughening behavior of cement pastes and forecasts the temperature increment [31][32]. The concrete temperature due to hydration is mainly governed by the mix and material properties and ecological factors [32][63]. In terms of using FA, FA affects cement hydration rate, as indicated by the hydration concept. An opposing effect of FAs on hydration kinetics was observed because of differences in their chemical composition. For instance, the effect of Class C FA on hydration is variable, while Class F FAs decrease the hydration. Previous research has revealed that hydrating clinker phases were improved when FA is available within the first hydration days [64][65].

Table 2. Summary of Ca-based and Na/K-based activators in FA concrete.
Mix Activator Records Findings Refs.
FA + OPC Ca(OH)2 Mild activation with pH between 7 and 13. Enhanced pozzolanic activity in long-term behavior. Making reaction with soluble salts to produce insoluble Ca-compounds and increase the alkalinity. [159]
FA Hydrothermal treatment at a temperature of 130 °C. Helped the formation of Al-substituted 11 Å tobermorite and hibschite. [260]
FA + OPC CaO For low-Ca FA, CaO was simply beneficial throughout early ages. As for high-Ca FA, the CaO was beneficial during both early and later ages. Optimum dosage of 3% CaO. No enhancement influence was found with CaO content more than 5%. [261]
FA CaO was as a less effective additive compared to Ca(OH)2. CaO displayed favorable effects when AAM cured at ambient temperature exhibited unfavorable influences when cured at elevated temperatures. [262]
FA + Lime CaCl2 It lowered the pH of pastes, however, enhanced Ca(OH)2 dissolution. 4% CaCl2 at 23 °C reduced early strength and improved later strength, but it improved both from 35 to 65 °C. [263]
FA + Limestone Mixture with 1.7% CaCl2 and 10% FA is the optimum mix. CaCl2 offered a considerable improvement in both early and long age strength and in accelerated setting time. [248]
FA + Lime CaSO4 Encouraged the formation of ettringite and dihydrate calcium sulfate. Accelerated the pozzolanic activity of FA and considerably enhanced the early age strength of the binder. [264]
FA + OPC Anhydrite is more efficient at amending early age strength, however, it is less efficacious at enhancing later age strength than gypsum. 10% anhydrite improved the 3 days fc by 70% and showed lower porosity and smaller pore sizes. [265]
FA NaOH Growing T triggered a reduction of Si/Al in aluminosilicate gel. Hydrates including traces of zeolite plus amorphous alkali aluminosilicate. [266]
FA Cured for 24 h at 30 °C. at high (OH/Al) ratio, NaOH promoted more 6-coordinate Al.
FA + Slag Curing at ambient temperature. At 28 days, fc = 50 MPa with 10 M NaOH.
FA + OPC Na2CO3 3% and curing in ambient temperature. Mortar exhibited 28 days fc = 14.8 MPa (fc = 22.0 MPa when there was no activator group).
FA + Ca(OH)2 Na2CO3 did not amend strength for NaOH-activated FA. A noticeable enhancement in microstructure and strength was attained. [267]
FA + OPC Na2SO4 Ash can be activated at earlier ages by increasing the creation of AFt and alkalinity. Compressive strength of mortar is improved by 40% for the first 3–7 days. [105]
FA + Lime Na2SO4 enhanced lime consumption on the first day and then did not thereafter. 4% NaSO4 improved paste strength at both earlier and later age. [248]
FA + NaOH Cured at 85 °C. Converting of N-A-S-H gel into zeolites is enhanced. Sulfates are acting as an activation retarding agent once NaOH is the activator. [268]
FA + OPC K2SO4 1% K2SO4 and cured at 20 °C. It is beneficial in lowering the total porosity and improving the early strength. [269]
FA Na2SiO3 Modulus was kept maintained at 1.0 when it was cured at 80 °C. Activation of Na2SiO3 is not appropriate for high-Ca ash, however appropriate for high-Ca ash.  
FA Cured at 60 °C for 24 h. The strength of paste was largely linked to the gel-like hydrates at modulus of 1.64, and the formation of crystalline Na2SiO3 resulted in higher compressive strengths with the corresponding modulus = 1.0.  
FA + NaOH Na2CO3 The major cause of strength was not due to a high pH at the early stage of NaOH formation. Na2CO3 did not amend the compressive strength of the NaOH-activated FA binder.  
FA + OPC Secondary phases, such as AFm and gaylussite, were preferred. Na2CO3 favored precipitation of C-A-S-H-like gel over (N, C)-A-S-H-like gel.  

Furthermore, FA particles exhibit a similar phenomenon to the glass. It was illustrated that glass particles were shielded with fibrous hydrates layer, signifying C-S-H’s propensity to nucleate on glass surfaces. In addition, the C-S-H formed from hydrating FA cement pastes is comparable to the cement substitution by metakaolin and slag, with a high surface area and a foil-like morphology [66]. The CaO/SiO 2 ratio of the C-S-H produced in mixes containing FA was less than those in mixes with cement [67].

The total heat produced by hydration of OPC and mixed pastes with FA in 2 days is shown in Figure 4 [68]. As shown in the figure, the total heat emitted during the hydration of mixed pastes was lower than that of OPC paste. With an increase in the amount of FA, the amount of hydration heat decreased, which was attributed to the combined impact of the increased FA content and diluting OPC [69].

Figure 4. Cumulative heat of hydration after 2-days for cement and different FA-based pastes [140]. Reprinted with permission from Elsevier [140].

Summary of Ca-based and Na/K-based activators in FA concrete.

5. Utilizations of FA

The construction industry is one of the world’s fastest-growing sectors. According to statistics, approximately 260 billion tons of cement is needed to meet various global construction needs [70]. Over the next ten years, it is estimated that this quantity will increase by 25%. Using waste material in concrete is one way to minimize cement demand. Eco-friendly concrete can be made from various waste materials, including FA as a partial cement substitute. FA disposal and utilization has been a big concern given the reliance of many countries on thermal power generation. Scientists, technologists, and engineers will face a new challenge in the future management of FA. Furthermore, FAs as binders or fillers are usually dumped in landfill and open fields, creating health hazards and environmental pollution issues [13][71]. Many authors have evaluated its potential as a building and construction material due to its abundance and excellent pozzolanic properties. For potential housing projects, FA is a promising partial cement replacement material [72]. Generally, FA is used as an SCM in concrete production and other materials shown in Figure 5. Several FA utilization areas include mine filling, construction of roads, and several building components (e.g., bricks and tiles) (Figure 6).
Figure 5. Modulus of elasticity versus age of Saudi FA (SFA)-based concrete [41]. Reprinted with permission from Elsevier [41].
Figure 6. Common applications of FA around the world [73]. Reprinted with permission from Elsevier [72].
Researchers have identified key applications for FA in the future based on the yearly time series data by recognizing a pattern of development using regression analysis [74][75] and the amount of FA to be used in choice and specific applications have been predicted, as shown in Figure 7 [76][77]. The greatest use of ash, to the amount of 44.19%, was anticipated in the concrete and cement industries in 2020–2021. The next-highest, 15.25% of ash, is to be used in ash dyke raising, roads, and embankments, another 12.49% in landfilling and retrieval of lowland areas, 7.61% in bricks and blocks, 8.84% in tiles and mine-filling, 2.47% in cultivation, and 9.14% in other structures. Therefore, the top five application industries are (i) concrete and cement, (ii) embankments, ash dykes, and rising roads, (iii) lowland area retrieval and landfilling, (iv) bricks and blocks, and (v) mine-filling and tiles, based on the upcoming skills. The amount of FA used in other applications could change in the coming years. Based on the literature review, no study has been conducted on utilizing boiler ash in the production of AAMs. Therefore, future work should be conducted to use boiler ash as an AAM material.
Figure 7. Typical applications of FA [76]. Reprinted with permission from Elsevier [76].

6. Conclusions

The use of FA as an SCM in concrete could resolve the disposal and health issues induced by the generation of ash due to coal combustion in industrial boilers or electric utility. The use of FA in concrete could also help lower the pollution induced by the cement factories by decreasing the CO2 emissions in the cement production. FA-based concrete exhibit high pozzolanic activity, opposed to their mineralogical characteristics and fineness properties. Most of the existing studies did not consider the effect of main influential parameters, particularly particle size distribution, particle packing effect, and alkaline activator solutions, on the strength development of FA-based concrete. FA is potentially utilized to substitute a significant volume of OPC (up to 50%) without influencing concrete durability. However, using 50% FA as a replacement by the cement weight may negatively affect the concrete strength. FA’s fineness has a significant role in concrete because it affects the workability and the rate of pozzolanic activity in concrete, thereby contributing to the enhancement of the properties of concrete. FA-based concrete demonstrated a superior performance to that of OPC-based concrete in resisting sulfate attack, acid attack, and carbonation. To approve the favorable influences of FA on concrete characteristics and durability problems, the following research directions are recommended for future studies.
The manufacturing and improvement of the performance of FA-based AAM must be controlled, and the reaction aspects of the material should be studied in detail. To this end, several facets, for instance, kinetics, thermodynamics, sympathies of intermediates and perceptions into their systems, and the grades to which the Si-O-Al are polymerized and oligomerized, should be studied. These will develop progressively improved performance of the concrete when the extra additives or components are involved. However, further research is needed to confirm that the manufacturing–structure–behaviors correspondence is accurate.
The majority of FA-based AAMs are stiff and susceptible to cracking. This performance obliges restrictions in applications and influences the long-term durability of AAMs. Therefore, innovations in the preparation must be applied to produce improved FA-based AAM composites.
Currently, FA-based AAMs are only formed at the research laboratory scale with empirical formulations. Thus, several studies on FA-based AAM production are required and must endeavor to adopt FA-based AAMs on a large scale.
The performance of FA-based AAMs for immobilization, toxic metal adsorption and the sealing of CO2 remained unsatisfactory. However, shifting the guidelines for preparation is worthy of further investigation.
As an alternative material to conventional concrete, FA-based AAM may be endowed with unique properties or additional functionalities. Therefore, novel applications of FA-based AAMs are worth discovering. For example, FA-based AAMs with biomass can be approved as new light-weight and incombustible materials.
The potential use of FA in producing high-strength and self-consolidating concretes must be studied.
Fibers must be used to increase the strength and longevity of FA in the concrete hardened state.
The use of FA in the design of eco-friendly buildings and cities should be highlighted.


  1. Shaikh, F.U.A. Mechanical and durability properties of fly ash geopolymer concrete containing recycled coarse aggregates. Int. J. Sustain. Built Environ. 2016, 5, 277–287.
  2. Shalini, A.; Gurunarayanan, G.; Kumar, R.; Prakash, V.; Sakthivel, S. Performance of Rice Husk Ash in Geopolymer Concrete. Int. J. Innov. Res. Sci. Technol. 2016, 2, 73–77.
  3. Castel, A.; Foster, S.J. Bond strength between blended slag and Class F fly ash geopolymer concrete with steel reinforcement. Cem. Concr. Res. 2015, 72, 48–53.
  4. Madheswaran, C.; Gnanasundar, G.; Gopalakrishnan, N. Effect of molarity in geopolymer concrete. Int. J. Civ. Struct. Eng. 2013, 4, 106–115.
  5. Amran, Y.H.M.; Alyousef, R.; Alabduljabbar, H.; El-Zeadani, M. Clean production and properties of geopolymer concrete; A review. J. Clean. Prod. 2020, 251, 119679.
  6. Amran, M.; Fediuk, R.; Murali, G.; Vatin, N.; Karelina, M.; Ozbakkaloglu, T.; Krishna, R.S.; Kumar, S.A.; Kumar, D.S.; Mishra, J. Rice husk ash-based concrete composites: A critical review of their properties and applications. Crystals 2021, 11, 168.
  7. Amran, M.; Murali, G.; Fediuk, R.; Vatin, N.; Vasilev, Y.; Abdelgader, H. Palm oil fuel ash-based eco-efficient concrete: A critical review of the short-term properties. Materials 2021, 14, 332.
  8. Abutaha, F.; Abdul Razak, H.; Kanadasan, J. Effect of palm oil clinker (POC) aggregates on fresh and hardened properties of concrete. Constr. Build. Mater. 2016, 112, 416–423.
  9. Bouasria, M.; Khadraoui, F.; Benzaama, M.-H.; Touati, K.; Chateigner, D.; Gascoin, S.; Pralong, V.; Orberger, B.; Babouri, L.; El Mendili, Y. Partial substitution of cement by the association of Ferronickel slags and Crepidula fornicata shells. J. Build. Eng. 2021, 33, 101587.
  10. Amran, M.; Debbarma, S.; Ozbakkaloglu, T. Fly ash-based eco-friendly geopolymer concrete: A critical review of the long-term durability properties. Constr. Build. Mater. 2021, 270, 121857.
  11. Lavaniyah, S.; Mohammed, B.S.; Al-Fakih, A.; Wahab, M.M.A.; Liew, M.S.; Amran, Y.H. Acid and Sulphate Attacks on a Rubberized Engineered Cementitious Composite Containing Graphene Oxide. Materials 2020, 13, 3125.
  12. Siddika, A.; Amin, M.R.; Rayhan, M.A.; Islam, M.S.; Mamun, M.A.A.; Alyousef, R.; Amran, Y.H.M. Performance of sustainable green concrete incorporated with fly ash, rice husk ash, and stone dust. Acta Polytech. 2021, 61, 279–291.
  13. Gatto, M.; Wollni, M.; Qaim, M. Oil palm boom and land-use dynamics in Indonesia: The role of policies and socioeconomic factors. Land Use Policy 2015, 46, 292–303.
  14. Awalludin, M.F.; Sulaiman, O.; Hashim, R.; Nadhari, W.N.A.W. An overview of the oil palm industry in Malaysia and its waste utilization through thermochemical conversion, specifically via liquefaction. Renew. Sustain. Energy Rev. 2015, 50, 1469–1484.
  15. Salim, N.; Nordin, N.A.; Hashim, R.; Ibrahim, M.; Sato, M. The potential of oil palm trunk biomass as an alternative source for compressed wood. BioRes 2012, 7, 2688–2706.
  16. Hwang, J.P.; Shim, H.B.; Lim, S.; Ann, K.Y. Enhancing the durability properties of concrete containing recycled aggregate by the use of pozzolanic materials. KSCE J. Civ. Eng. 2013, 17, 155–163.
  17. Chindaprasirt, P.; Homwuttiwong, S.; Jaturapitakkul, C. Strength and water permeability of concrete containing palm oil fuel ash and rice husk-bark ash. Constr. Build. Mater. 2007, 21, 1492–1499.
  18. Jaturapitakkul, C.; Kiattikomol, K.; Tangchirapat, W.; Saeting, T. Evaluation of the sulfate resistance of concrete containing palm oil fuel ash. Constr. Build. Mater. 2007, 21, 1399–1405.
  19. Bilek, V.; Sucharda, O.; Bujdos, D. Frost Resistance of Alkali-Activated Concrete—An Important Pillar of Their Sustainability. Sustainability 2021, 13, 473.
  20. Sata, V.; Jaturapitakkul, C.; Kiattikomol, K. Influence of pozzolan from various by-product materials on mechanical properties of high-strength concrete. Constr. Build. Mater. 2007, 21, 1589–1598.
  21. Gollakota, A.R.K.; Volli, V.; Shu, C.M. Progressive utilisation prospects of coal fly ash: A review. Sci. Total Environ. 2019, 672, 951–989.
  22. Islam, A.; Alengaram, U.J.; Jumaat, M.Z.; Bashar, I.I.; Kabir, S.M.A. Engineering properties and carbon footprint of ground granulated blast-furnace slag-palm oil fuel ash-based structural geopolymer concrete. Constr. Build. Mater. 2015, 101, 503–521.
  23. Alengaram, U.J.; Al Muhit, B.A.; bin Jumaat, M.Z. Utilization of oil palm kernel shell as lightweight aggregate in concrete—A review. Constr. Build. Mater. 2013, 38, 161–172.
  24. Alengaram, U.J.; Al Muhit, B.A.; bin Jumaat, M.Z.; Jing, M.L.Y. A comparison of the thermal conductivity of oil palm shell foamed concrete with conventional materials. Mater. Des. 2013, 51, 522–529.
  25. Sata, V.; Wongsa, A.; Chindaprasirt, P. Properties of pervious geopolymer concrete using recycled aggregates. Constr. Build. Mater. 2013, 42, 33–39.
  26. Kabir, S.M.A.; Alengaram, U.J.; Jumaat, M.Z.; Sharmin, A.; Islam, A. Influence of molarity and chemical composition on the development of compressive strength in POFA based geopolymer mortar. Adv. Mater. Sci. Eng. 2015, 2015, 647071.
  27. Lesovik, V.; Volodchenko, A.; Fediuk, R.; Amran, Y.H.M.; Timokhin, R. Enhancing performances of clay masonry materials based on nanosize mine waste. Constr. Build. Mater. 2021, 269, 121333.
  28. Danish, A.; Mosaberpanah, M.A. Formation mechanism and applications of cenospheres: A review. J. Mater. Sci. 2020, 55, 4539–4557.
  29. Meesala, C.R.; Verma, N.K.; Kumar, S. Critical review on fly-ash based geopolymer concrete. Struct. Concr. 2020, 21, 1013–1028.
  30. Lesovik, V.; Voronov, V.; Glagolev, E.; Fediuk, R.; Alaskhanov, A.; Amran, Y.H.M.; Murali, G.; Baranov, A. Improving the behaviors of foam concrete through the use of composite binder. J. Build. Eng. 2020, 31, 101414.
  31. Sujivorakul, C.; Jaturapitakkul, C.; Taotip, A. Utilization of Fly Ash, Rice Husk Ash, and Palm Oil Fuel Ash in Glass Fiber–Reinforced Concrete. J. Mater. Civ. Eng. 2011, 23, 1281–1288.
  32. Chindaprasirt, P.; Chotetanorm, C.; Rukzon, S. Use of Palm Oil Fuel Ash to Improve Chloride and Corrosion Resistance of High-Strength and High-Workability Concrete. J. Mater. Civ. Eng. 2011, 23, 499–503.
  33. Abdullah, K.; Hussin, M.W.; Zakaria, F.; Muhamad, R.; Abdul Hamid, Z. A potential partial cement replacement material in aerated concrete. In Proceedings of the 6th Asia-Pacific Structural Engineering and Construction Conference, Kuala Lumpur, Malaysia, 5–6 September 2006.
  34. Awal, A.S.M.A.; Abubakar, S.I. Properties of concrete containing high volume palm oil fuel ash: Ashort-term investigation. Malays. J. Civ. Eng. 2011, 23, 164–176.
  35. Adam, A. Strength and Durability Properties of Alkali Activated Slag and Fly Ash-Based Geopolymer Concrete. Ph.D. Thesis, RMIT University, Melbourne, VIC, Australia, August 2009.
  36. Bakri, A.; Mustafa, M.; Mohammed, H.; Kamarudin, H.; Niza, I.K.; Zarina, Y. Review on fly ash-based geopolymer concrete without Portland Cement. J. Eng. Technol. Res. 2011, 3, 1–4.
  37. Hardjito, D.; Wallah, S.E.; Sumajouw, D.M.J.; Rangan, B.V. Introducing fly ash-based geopolymer concrete: Manufacture and engineering properties. In Proceedings of the 30th Conference on Our World in Concrete and Structures, Singapore, 23–24 August 2005.
  38. Hardjito, D.; Wallah, S.E.; Sumajouw, D.M.J.; Rangan, B.V. Fly Ash-Based Geopolymer Concrete. Aust. J. Struct. Eng. 2005, 6, 77–86.
  39. Ryu, G.S.; Lee, Y.B.; Koh, K.T.; Chung, Y.S. The mechanical properties of fly ash-based geopolymer concrete with alkaline activators. Constr. Build. Mater. 2013, 47, 409–418.
  40. Alsubari, B.; Shafigh, P.; Ibrahim, Z.; Jumaat, M.Z. Heat-treated palm oil fuel ash as an effective supplementary cementitious material originating from agriculture waste. Constr. Build. Mater. 2018, 167, 44–54.
  41. Kumaravel, S. Development of various curing effect of nominal strength Geopolymer concrete. J. Eng. Sci. Technol. Rev. 2014, 7, 116–119.
  42. Liu, B.; Shi, J.; Zhou, F.; Shen, S.; Ding, Y.; Qin, J. Effects of steam curing regimes on the capillary water absorption of concrete: Prediction using multivariable regression models. Constr. Build. Mater. 2020, 256, 119426.
  43. Patil, A.A.; Chore, H.; Dodeb, P. Effect of curing condition on strength of geopolymer concrete. Adv. Concr. Constr. 2014, 2, 29–37.
  44. Manesh, S.B.; Madhukar, R.W.; Subhash, V.P. Effect of duration and temperature of curing on compressive strength of geopolymer concrete. Int. J. Eng. Innov. Technol. 2012, 1, 152–155.
  45. Shafigh, P.; Jumaat, M.Z.; Mahmud, H.B.; Hamid, N.A.A. Lightweight concrete made from crushed oil palm shell: Tensile strength and effect of initial curing on compressive strength. Constr. Build. Mater. 2012, 27, 252–258.
  46. Method for Making Test. Cylinders from Fresh Concrete; BS-1881:Part-110; British Standards Institution: London, UK, 1983.
  47. Galau, D.; Ismai, M. Characterization of Palm Oil Fuel Ash (POFA) from Different Mill as Cement Replacement Materials; Universiti Teknologi Malaysia: Johor Bahru, Malaysia, 2010.
  48. Provis, J.L. Alkali-activated materials. Cem. Concr. Res. 2018, 114, 40–48.
  49. Jong, L.Y.; Teo, D.C.L. Concrete Containing Palm Oil Fuel Ash (POFA) and Oil Palm Shell (OPS) Subjected to Elevated Temperatures. J. Civ. Eng. Sci. Technol. 2014, 5, 13–17.
  50. Chernysheva, N.; Lesovik, V.; Fediuk, R.; Vatin, N. Improvement of Performances of the Gypsum-Cement Fiber Reinforced Composite (GCFRC). Materials 2020, 13, 3847.
  51. Umar, M.S.; Jennings, P.; Urmee, T. Strengthening the palm oil biomass Renewable Energy industry in Malaysia. Renew. Energy 2013, 60, 107–115.
  52. Segui, P.; Aubert, J.E.; Husson, B.; Measson, M. Characterization of wastepaper sludge ash for its valorization as a component of hydraulic binders. Appl. Clay Sci. 2012, 57, 79–85.
  53. Alomayri, T.; Shaikh, F.U.A.; Low, I.M. Synthesis and mechanical properties of cotton fabric reinforced geopolymer composites. Compos. Part. B Eng. 2014, 60, 36–42.
  54. Zeyad, A.M.; Johari, M.A.M.; Tayeh, B.A.; Yusuf, M.O. Efficiency of treated and untreated palm oil fuel ash as a supplementary binder on engineering and fluid transport properties of high-strength concrete. Constr. Build. Mater. 2016, 125, 1066–1079.
  55. Shaikh, F.U.A. Effects of alkali solutions on corrosion durability of geopolymer concrete. Adv. Concr. Constr. 2014, 2, 109–123.
  56. Mohammed, B.S.; Al-Ganad, M.A.; Abdullahi, M. Analytical and experimental studies on composite slabs utilising palm oil clinker concrete. Constr. Build. Mater. 2011, 25, 3550–3560.
  57. ASTM Standard Test. Method for Splitting Tensile Strength of Cylindrical Concrete Specimens C496/C496M-04; ASTM: West Conshohocken, PA, USA, 2004.
  58. Joseph, B.; Mathew, G. Influence of aggregate content on the behavior of fly ash based geopolymer concrete. Sci. Iran. 2012, 19, 1188–1194.
  59. Boonserm, K.; Sata, V.; Pimraksa, K.; Chindaprasirt, P. Improved geopolymerization of bottom ash by incorporating fly ash and using waste gypsum as additive. Cem. Concr. Compos. 2012, 34, 819–824.
  60. Awal, A.S.M.A.; Shehu, I.A.; Ismail, M. Effect of cooling regime on the residual performance of high-volume palm oil fuel ash concrete exposed to high temperatures. Constr. Build. Mater. 2015, 98, 875–883.
  61. Prabhu, R.; Anuradha, R.; Vivek, S. Experimental Research on Triple Blended Self-Compacting Geo Polymer Concrete. Asian J. Eng. Appl. Technol. 2016, 5, 15–21.
  62. Dhakal, S. Urban energy use and carbon emissions from cities in China and policy implications. Energy Policy 2009, 37, 4208–4219.
  63. Haridharan, M.K.; Matheswaran, S.; Murali, G.; Abid, S.R.; Fediuk, R.; Amran, Y.H.M.; Abdelgader, H.S. Impact response of two-layered grouted aggregate fibrous concrete composite under falling mass impact. Constr. Build. Mater. 2020, 263, 120628.
  64. Alengaram, U.J.; Mahmud, H.; Jumaat, M.Z. Comparison of mechanical and bond properties of oil palm kernel shell concrete with normal weight concrete. Int. J. Phys. Sci. 2010, 5, 1231–1239.
  65. Ayzenshtadt, A.; Lesovik, V.; Frolova, M.; Tutygin, A.; Danilov, V. Nanostructured wood mineral composite. Procedia Eng. 2015, 17, 45–51.
  66. Sata, V.; Jaturapitakkul, C.; Kiattikomol, K. Utilization of Palm Oil Fuel Ash in High-Strength Concrete. J. Mater. Civ. Eng. 2004, 16, 623–628.
  67. Tonnayopas, D.; Nilrat, F.; Putto, K.; Tantiwitayawanich, J. Effect of oil palm fiber fuel ash on compressive strength of hardening concrete. Renew. Energy 2006, 1, 1–3.
  68. Karayannis, V.G.; Moustakas, K.G.; Baklavaridis, A.N.; Domopoulou, A.E. Sustainable ash-based geopolymers. Chem. Eng. Trans. 2018, 63, 505–510.
  69. Siler, P.; Kratky, J.; De Belie, N. Isothermal and solution calorimetry to assess the effect of superplasticizers and mineral admixtures on cement hydration. J. Therm. Anal. Calorim. 2012, 107, 313–320.
  70. Murali, G.; Abid, S.R.; Abdelgader, H.S.; Amran, Y.H.M.; Shekarchi, M.; Wilde, K. Repeated Projectile Impact Tests on Multi-Layered Fibrous Cementitious Composites. Int. J. Civ. Eng. 2021, 19, 635–651.
  71. Sideris, K.K.; Savva, A.E.; Papayianni, J. Sulfate resistance and carbonation of plain and blended cements. Cem. Concr. Compos. 2006, 28, 47–56.
  72. Hong, D.L.H.; Mohammed, B.S.; Al-Fakih, A.; Wahab, M.M.A.; Liew, M.S.; Mugahed Amran, Y.H. Deformation properties of rubberized ecc incorporating nano graphene using response surface methodology. Materials 2020, 13, 2831.
  73. Triantafillou, T.C. Textile Fibre Composites in Civil. Engineering, 1st edition; Woodhead Publishing: Sawston, UK, 2016; ISBN 9781782424697.
  74. Flower, D.J.M.; Sanjayan, J.G. Greenhouse gas emissions due to concrete manufacture. Int. J. Life Cycle Assess. 2007, 12, 282–288.
  75. Fediuk, R.; Pak, A.; Kuzmin, D. Fine-Grained Concrete of Composite Binder. In Proceedings of the IOP Conference Series: Materials Science and Engineering, Birmingham, UK, 13–15 October 2017; IOP Publishing Ltd.: Bristol, UK, 2017.
  76. Yao, Z.T.; Ji, X.S.; Sarker, P.K.; Tang, J.H.; Ge, L.Q.; Xia, M.S.; Xi, Y.Q. A comprehensive review on the applications of coal fly ash. Earth-Sci. Rev. 2015, 141, 105–121.
  77. Ren, X.; Qu, R.; Liu, S.; Zhao, H.; Wu, W.; Song, H.; Zheng, C.; Wu, X.; Gao, X. Synthesis of zeolites from coal fly ash for the removal of harmful gaseous pollutants: A review. Aerosol Air Qual. Res. 2020, 20, 1127–1144.
Contributor MDPI registered users' name will be linked to their SciProfiles pages. To register with us, please refer to :
View Times: 515
Revisions: 3 times (View History)
Update Date: 24 Nov 2021
Video Production Service