1. History

The 3-inch mine defense guns were part of a comprehensive plan of new fortifications specified by the Endicott Board of 1885. The new forts included guns up to 12-inch (305 mm) on disappearing carriages, to conceal the fort from observation from the sea. The 3-inch guns were the smallest of these guns, intended to protect remotely controlled minefields against minesweepers. For most of their service they were operated by the United States Army Coast Artillery Corps.

1.1. M1898

The M1898 was the first of the new 3-inch guns developed. It was manufactured by Driggs-Seabury and was on an M1898 "masking parapet" retractable carriage, conceptually similar to the disappearing carriages of the larger guns. 111 of these weapons were emplaced 1899–1905. The carriage could only be retracted when the gun was at a particular train angle (in most installations 90° off the emplacement axis in either direction), thus it provided no concealment in action. Eventually the retraction feature was disabled, with the modified carriage designated M1898MI. The weapon was in any case small enough that the risk of observation from the sea was minimal.^[1] Most or all of the M1898 guns and carriages were removed from service in 1920 due to obsolescence and probably the manufacturer's bankruptcy.^[2][3]

An unusual emplacement for the M1898 guns was at Fort Mott, New Jersey, near Fort Delaware. Two guns were in a massive casemated emplacement named Battery Edwards, converted from an 1870s magazine. At this location it was determined that the minefields needed maximum protection.^[4][5]

1.2. M1902

The M1902 was functionally similar to the M1898, but was manufactured by Bethlehem Steel and was on a non-retractable pedestal carriage. 60 of these weapons were emplaced 1903–1910.^[6] It was not the same weapon as the 3-inch M1902 field gun.

1.3. M1903

The M1903 was a slight improvement on the M1902 with the bore lengthened from 50 calibers to 55 calibers for increased range. References vary as to whether the bore was lengthened or not, but the increase in overall length supports that it was. The weapon was manufactured by Watervliet Arsenal and was on a non-retractable pedestal carriage. 101 of these weapons were emplaced 1904–1917.^[7]

1.4. Basis for Anti-Aircraft Guns

The 3-inch gun M1917 was a World War I-era US-made anti-aircraft gun based on the 3-inch gun M1903. It was designed for a fixed mounting and remained in service, primarily at Coast Artillery installations, through World War II. It was determined that the weapon was too heavy and had too much recoil for mobile mountings, so a new weapon based on the lighter and less powerful 3-inch gun M1898 was developed, designated the 3-inch Gun M1918. This was the standard US anti-aircraft gun until replaced by the 3-inch gun M3 in 1930. There is some controversy as to whether any seacoast guns were actually converted into anti-aircraft guns in the development of these weapons.^[8][9]

1.5. Replacement

As part of an across-the-board modernization, all types of 3-inch seacoast guns (with some exceptions) were replaced by the 90 mm Gun M1 in 1940–44 during World War II, usually in new locations. The new weapons were called Anti Motor Torpedo Boat (AMTB) guns. As they were replaced, most of the 3-inch guns were scrapped, along with almost all older Coast Artillery weapons. Almost all remaining weapons, including the new 90 mm guns, were scrapped shortly after the war ended in 1945.

2. Where Used

The 3-inch guns M1898, M1902, and M1903 were used at most of the coastal forts that were built under the recommendations of the Endicott Board and Taft Board. A total of 272 were emplaced worldwide 1899–1917. The number of guns in each battery varied from one to four (six in one case), but was most commonly two. The number of batteries in a fort also varied; many forts had only one 3-inch gun battery, while some had as many as four.^[10]

3. Design and Construction

3.1. 3-Inch Gun M1903

The gun barrel is of the built-up type. The jacket fits over the rear end of the tube and projects beyond it. The breech bushing is screwed into the end of the jacket and the breech mechanism is assembled into the bushing. The breech bushing bears interrupted threads for the breechblock.^[11]

3.2. Breech Mechanism

The function of the breech mechanism is to close the breech, and thereby hold the cartridge case in place. The breechblock is the main part of the mechanism. It closes the breech and is hinged so that it can be swung open for loading. It is moved by an operating lever. The lever and breechblock are connected by an operating bar, operating in a T-slot in the breechblock carrier. Thus connected, complete motion of the operating lever to the right will cause the breechblock to rotate and to be swung clear of the breech recess. Swinging the operating lever fully to the right engages cam surfaces of the breechblock carrier and extractor, causing the extractor to eject the empty cartridge case.^[11]

3.3. Firing Mechanism

The firing mechanism is known as the continuous pull, percussion type; that is, no cocking of the firing pin is required other than a pull on the lanyard or trigger shaft.^[11]

3.4. Pedestal Carriage M1903

The gun carriage consists of a pedestal, bolted rigidly to the concrete emplacement, and of a gun-supporting structure, which rests on the pedestal and is capable of traversing upon it. The pedestal is the foundation piece of the gun carriage. On the M1903 carriage the pivot yoke is mounted in the pedestal and rests upon a ring of ball bearings on the base of the pedestal. The entire weight of the gun and top part of the carriage rests upon this ring of ball bearings. The bushings for the pivot yoke form two supports against the thrust of firing. At the upper end of the pivot yoke, on either side, trunnion bearings are provided for the cradle trunnions. The shield and shield supports are bolted to the pivot yoke. The opening for the gun in the shield is prolonged underneath to allow for the removal of the piston and springs from the recoil cylinder.^[11]

The carriage consists of recoil and counterrecoil mechanism, elevation mechanism and traversing mechanism. In addition, the M1903 carriage has a range drum.^[11]

A recoil cylinder checks the recoil of the gun, and a spring inside the recoil cylinder returns the gun to battery.^[11]

On the M1903 carriage a friction band is provided and is adjusted so as to allow a certain amount of friction between itself and the traversing rack.^[11]

4. Gun Crew

A gun battery consists of one or more gun emplacements, and is under the command of the battery commander. The battery commander is assisted by a battery executive and an assistant battery executive. These positions are filled by officers.^[12]

Each gun in an emplacement is manned by a gun section consisting of a gun squad of 15 (war strength) or 12 (peace strength) enlisted men including one noncommissioned officer, the chief of section, and an ammunition squad of 9 (war strength) or 6 (peace strength) enlisted men including one noncommissioned officer, the chief of ammunition.^[12]

5. Ammunition

The ammunition for this gun is fixed and of a weight that can be handled entirely by hand. The ammunition is brought from the magazine to the gun and held ready for loading. To load, push the shell home into the breech recess of the gun with a moderately quick motion of the hand.^[11]

Ammunition for the 3-inch gun M1903 is issued in the form of fixed complete rounds. The term "fixed" signifies that the propelling charge is fixed (not adjustable) and that the round is loaded into the gun as a unit. The propelling charge is assembled loosely in the cartridge case which is crimped rigidly to the projectile. A complete round of ammunition comprises all of the components necessary to fire one round.^[11]

Dependent upon the type of projectile, ammunition for these guns is classified as high explosive, target practice, blank, or drill. The high explosive projectile contains a high explosive filler. The target practice projectile contains no explosive; it consists of either a solid projectile (designated shot) or a heavy-walled projectile with an empty base cavity. The blank ammunition has a black powder (low explosive) charge in the cartridge case and no projectile. The drill ammunition consists of completely inert cartridge which simulates the service ammunition.^[11]

All projectiles are painted to prevent rust and corrosion and by the color to provide a ready means of identification as to type. The projectiles of the ammunition described herein are painted as follows:^[11]

Note that the above color scheme is not wholly in agreement with the basic color scheme, described in TM 9-1900, practice projectiles being generally painted blue.^[11]

6. Specifications

Specifications from TM 9-421^[11]

Traverse dependent upon construction and emplacement^[11]

7. Surviving Examples

At least 23 3-inch seacoast guns, four mountings, and two training dummies survive:^[13][14][15]

• Two 3-inch guns M1902M1 (#6 and #7 Bethlehem) at Battery Irwin, Fort Monroe, VA
• Two 3-inch guns M1903 (#11 and #12) at Battery Trevor, Fort Casey, Coupeville, WA (guns moved in the 1960s from Battery Flake, Fort Wint, Grande Island, Subic Bay Philippines)
• One 3-inch gun M1903 (#17) at Battery Wansboro, Fort Flagler, Nordland, WA (gun moved in the 1960s from Battery Jewell, Fort Wint, Grande Island, Subic Bay Philippines)
• One 3-inch gun M1898M1 (#120 Driggs-Seabury), Central Park, West Rutland, Vermont
• One 3-inch gun M1898M1 (#75 Driggs-Seabury), Town Hall, Lacey Road, Forked River, New Jersey
• One 3-inch gun M1898M1, Valhalla Firehouse, Valhalla, NY
• One 3-inch gun M1898M1 (#122 Driggs-Seabury), Pulaski Square, Cleveland, OH
• One 3-inch gun M1898M1, Mount Pleasant Cemetery, Elbridge, New York
• One 3-inch gun M1898M1, Copper Street Cemetery, Vernon, NY
• Three 3-inch guns M1898M1, (#27, 28, 85 Driggs-Seabury), Valley Forge Military Academy and College, Wayne, PA
• One 3-inch gun M1898M1 (#92 Driggs-Seabury), Town Hall, Brighton, NY
• Two 3-inch guns M1898M1 (#37 and #38 Driggs-Seabury), American Legion post, Penfield, NY
• Two 3-inch guns M1898M1 (#11 and #118 Driggs-Seabury), Schell Memorial Cemetery, Boyertown, PA
• One 3-inch gun M1898M1 (#60 Driggs-Seabury), Route 22, Harrisburg, PA
• One 3-inch gun M1898M1 (#88 Driggs-Seabury), Orange, MA
• One 3-inch gun M1898M1 (#39 Driggs-Seabury), American Legion Post 397, Shrewsbury, MA
• One 3-inch gun M1898M1 (Unk. mfr.), Oregon Military Museum (closed since 2009, plans to re-open), Camp Withycombe, Clackamas, OR
• Four 3-inch masking parapet mounts M1898, FL Historical Resources Conservation Laboratory, Tallahassee, Florida (discovered at Fort Taylor, Key West, FL)
• One training dummy M1911 (#2 Watervliet) on barbette carriage M1912 (#1 Cowdrey Machine), U.S. Army Ordnance Training and Heritage Center, Fort Lee, VA
• One training dummy M1911 (#unk Watervliet) on barbette carriage M1912 (#unk Cowdrey Machine), Battery McCorkle, Fort Moultrie, Sullivan's Island, SC

The content is sourced from: https://handwiki.org/wiki/Engineering:3-inch_gun_M1903