1. History

LightScribe was conceived by Hewlett-Packard engineer Daryl Anderson, and the coating's chemistry was developed by Dr. Makarand Gore,^[1] and brought to market through the joint design efforts of HP's imaging and optical storage divisions, where it was first introduced in January 2004 at the 2004 Consumer Electronics Show.^[2][3]

It was the first direct to disc labeling technology that allowed users to laser etch images to the label side of a disc. DiscT@2 technology had been on the market since 2002, but DiscT@2 allows users to burn only to the unused portion of the data side of the disc. In 2005, LabelFlash became the main competitor for LightScribe.

Various brands manufacture the required media. Dual Layer DVD+Rs are the highest-capacity disc to support the technology.^[4] No LightScribe Blu-ray discs were ever developed or manufactured, though Blu-ray drives with LightScribe technology (supporting the older formats) were on the market.

Companies such as HP, Samsung, LaCie and LiteOn have discontinued or are phasing out LightScribe drives (As of June 2013)^[5] with only LG continuing to manufacturing drives; until the manufacturing of LG LightScribe drives was discontinued. (As of November 2013),^[6] LightScribe.com HP's official LightScribe website has been removed. This has been replaced with the following message:

Thank you for your interest in the LightScribe disc labeling technology. This website is no longer active. LightScribe software and disc utilities may be found on a number of public websites.

(As of April 2018), the website returns a 404 error.^[7] (As of November 2018), the website redirected to Hewlett-Packard's homepage. (As of June 2019), HP Desktop PCs Customer Support still has an article of instructions and FAQ about LightScribe.^[8]

2. Mode of Operation

The surface of a LightScribe disc is coated with a reactive dye that changes color when it absorbs 780 nm infrared laser light. The etched label will show no noticeable fading under exposure to indoor lighting for at least two years. Optical media should always be stored in a protective sleeve or case that keeps the data content in the dark and safe from scratches. If stored this way, the label should last the life of the disc in real-world applications.

LightScribe labels burn in concentric circles, moving outward from the center of the disc. Images with the largest diameters will take longest to burn.

LightScribe is monochromatic, initially a grey etch on a gold-looking surface. From late 2006, LightScribe discs are also available in various surface colors, under the v1.2 specification. The etching is still in shades of grey.

It is not possible to replace a LightScribe label with a new design (as in erase the surface of the disc), but it is possible to add more content to a label that has already been burned.

The center of every LightScribe disc has a unique code that, together with a sensor in the drive, allows the drive to know the precise rotational position of the disc. This, in combination with the drive hardware, allows it to know the precise position from the center outwards, and the disc can be labeled while spinning at high speed using these references. It also serves a secondary purpose: the same disc can be labeled with the same image multiple times. Each successive labeling will darken the blacks and increase image contrast (see drawbacks). Successive burns are perfectly aligned.

3. Drawbacks

Special storage precautions are necessary to prevent LightScribe discs from fading. HP's LightScribe website warns users to "keep discs away from extreme heat, humidity and direct sunlight", "store them in a cool, dark place", "use polypropylene disc sleeves rather than PVC sleeves", and also notes that "residual chemicals on your fingers could cause discoloration of the label image". Such chemicals include common hand lotions and hair care products.^[9] Users not observing these precautions have reported LightScribe discs to become visibly faded within two months in the worst case. This drawback makes the technology unsuitable for applications involving continuous handling, and for such popular uses as car music compilation discs, which typically have unavoidable high light and temperature exposure. Since many disc players present internal temperatures significantly higher than room temperature, LightScribe discs should also not be left in disc players for long periods of time.

LightScribe discs may form a visible white powder coating. This is due to crystallization of some of the label-side coating. It is not harmful and can easily be removed with a water-dampened cloth. Wiping the disc with a damp cloth does not harm the inscribed label.^[10] At this point, LightScribe support has not explained which conditions lead to this reaction, nor the precautions that can be taken to avoid it.

Multiple LightScribes of the same image increases contrast, but the image quality decreases with successive burns. Noticeable contrast variations are seen in solid shades.

4. Other Uses

A LightScribe optical drive was used by Maher El-Kady, a graduate of UCLA in 2012 to successfully turn a specially prepared graphite oxide layer coated onto a DVD into graphene.^[11] El-Kady and Richard Kaner, his lab professor, used an unmodified LightScribe drive. The disc was prepared by coating the disc with an aqueous solution of graphite oxide and allowing it to dry. Areas of the coating illuminated by the LightScribe laser were turned into graphene. Various shapes can be drawn, which allowed the scientist duo essentially to laser-print an ultracapacitor on graphene using consumer-grade technology. Another use is to prepare a PCB layout on an unburned LightScribe CD-R as there is enough contrast to form a weak shadow image on a photosensitive PCB with UV light. The ratio with a single pass is not that good but multiple burns are.

The content is sourced from: https://handwiki.org/wiki/Software:LightScribe