Wind Turbine Icing Modelling Approaches: History
Please note this is an old version of this entry, which may differ significantly from the current revision.
Contributor:

In this entry, a comprehensive review of wind turbine icing modelling is presented. The commonly applied approaches and the recent advances have been reported based on a systematic and concise literature review. The paper presents a panorama of the current modelling and simulation studies dealing with different aspects of ice accretion on wind turbines.

  • wind turbine icing
  • modelling of ice accretion
  • icing simulation
  • CFD

1. Introduction

Due to the rising concern over climate change, actual global trends move increasingly toward reducing greenhouse gas emissions. Among these actions is the investment in the exploitation of clean energy resources. According to Natural Resources Canada, about 78% of global greenhouse gas emissions from human activity are from production and energy consumption [1]. Consequently, during the last few decades, investment in clean energy technologies has been growing progressively. Wind energy production has been booming to become a significant part of the energy market and research worldwide [2]. The “BP Statistical Review of World Energy2021” revealed that wind provided the most significant contribution to renewables’ global growth in 2020 [3]. In Canada, electricity generation from renewable sources increased by 16% between 2010 and 2018, and wind energy has the most considerable growth [1]. Kumar, et al. [4] discussed the trends and the available technologies developed for wind energy in conjunction with their applications and devices of operation [4]. However, this technology is highly dependent on its geographic location.

Wind Turbine Icing is the phenomenon of ice build-up mainly on wind turbine blades. It is a common problem in Nordic countries, which has severe consequences on the operation and the life cycle of wind turbines. When wind turbine blades are subjected to supercooled water droplets under specific meteorological conditions, ice starts to build forward in different forms, types, and severities. The deposition of ice on the blades may affect the turbine’s structural integrity, causing much damage to the turbines and the surrounding areas. Safety hazards have been reported, such as the throwing of large chunks of ice may threaten the safety of the public, employees, and nearby roads and facilities [7]. Various types of icing consequences have been stated by the cited sources [8,9,10,11,12]. However, it is the shape rather than the mass or dimensions of ice that significantly impact wind energy production [7]. The accumulation of ice on the leading edge of blade section airfoils, even in small quantities, results in significant consequences on power production of the wind turbine due to the degradation of the aerodynamics performance associated with the iced airfoil deformation [7].

Research into wind turbine icing is a developing discipline with limited available resources for investigations [13]. Given that the phenomenon of ice accumulation is physically complex, the optimization of wind turbines operating under icing conditions depends essentially on experiments. However, experimental tests and wind farm observations being relatively costly and having many operational difficulties; numerical simulation has increasing importance as a means of compliance. By reproducing the ice accretion progression on wind turbines blades, a numerical simulation approach makes it possible to conveniently provide information on the aerodynamic and energy production losses, energy required for de-icing for different wind turbine configurations and weather conditions [14,15]. As computational cost drops, the use of computational fluid dynamics (CFD) for wind turbine design and analysis is becoming increasingly widespread. It results in a better understanding of the phenomenon and its consequences on wind turbines [16]. Thanks to the development of advanced icing simulation tools for aeronautics, the bibliographic study showed increasing interest in modelling and simulation research adapting these tools for wind turbine icing simulation during the last decade. The most commonly used icing simulation tools are LEWICE, developed by NASA and ANSYS FENSAP-ICE, developed by NTI Inc. The latter is often used recently in the literature for wind turbine icing due to its availability and integration with Ansys FLUENT and CFX. Based on what has been mentioned above, it is appropriate to review wind turbine icing modelling and provide engineers, analysts, or similar professionals in computational wind energy with icing simulation tools primarily validated with the operational conditions of wind turbines.

 
Unlike the previous icing studies, this paper, in addition to highlighting the problem of wind turbine icing in northern climates, focuses on the actual state-of-the-art of ice modelling and simulation. It provides guidelines to the knowledge needed for modelling the phenomenon and examines the numerical methods used to analyze ice. It provides the best practices and recommendations for the simulation of ice accretion on wind turbines. After reviewing hundreds of references available in the literature on wind turbine icing, investigations have been carried out on the art of modelling ice accretion, from the applicable theory and various mathematical and physical models to the methodological approaches adopted to conduct reliable modelling in this domain. The objective is to present and recommend trustworthy modelling tools that are capable, via numerical simulations, of predicting and quantifying icing and eventually adapting the wind turbines to handle severe winter conditions.

2. Computational Models for Ice Accretion

Typically, the computational procedure for ice accretion is a time-step iterative process. It requires considering four consecutive modules of calculation: flow field aerodynamic calculations, particle trajectory calculations, thermodynamic analysis and ice geometry generation. All the modelling techniques used in these modules depend on partial differential equations that require numerical solutions. This section outlines the approaches adopted when modelling ice accretion on wind turbine blades’ airfoils. 

In the aerodynamic module, commonly used turbulence models, such as the SPALART-ALLMARAS, k-ε and k-ω SST have been discussed in addition to surface roughness modelling. For the multiphase modelling of droplet trajectories, the Lagrangian and Eulerian approaches were discussed. Finally, the model of Messinger was discussed in the module of thermodynamic modelling of ice accretion.

Figure 6. Overview of the Thermodynamic module based on Messinger model for mass and energy balances. @Fahed Martini.

3. Research Survey on Modelling and Simulation of Ice Accretion on Wind Turbines

This section analyzes the different modelling approaches by evaluating their suitability and adequacy for wind turbine icing simulation to identify the most adapted techniques and methodologies. The survey addressed research on modelling the surface roughness, droplets trajectory and the electro-thermal icing protection systems.

For IPS modelling, a module for heat transfer is conjugated in the calculations. This includes the calculations of the heat transfer coefficient using a boundary layer calculation considering the roughness of the wall due to the presence of ice. Some commercial codes are equipped with this additional module to conduct simulations on the hot air or electro-thermal icing protection systems to estimate the energy consumption required for anti- or de-icing once the ice accretion is estimated. For example, LEWICE integrates a thermal anti-icing model for the calculation of the thermal energy required to prevent ice formation, available for two anti-icing modes of prevention: evaporative and running-wet conditions [83]. FENSAP-ICE also has a particular module (CHT3D) that incorporates heat flux distributions in icing calculations to estimate the required total heat load for the hot air or electro-thermal IPS for the two modes of prevention: evaporative and running-wet conditions [51].

Performance degradation due to Icing and heat flux simulation for different anti-icing scenarios are presented in a simulation study on wind turbine blades using FENSAP-ICE [79,80]. This showed the total power required for every considered surface coverage and power distribution for four icing cases. It is worth noting that for initial de-icing computations, the surface roughness should be considered in calculations as it is already determined during ice accretion. However, for anti-icing simulation, uncontaminated surfaces can be considered (with no roughness) since they are expected to remain free of ice [51].

Modelling of the electro-thermal Icing Protection Systems for wind turbines presents many challenges. They are presented and discussed, along with the mathematical models used in IPS modelling, in a published study by Fakorede, 2018 [114] on heat and mass transfer modelling during the anti/de-icing process for wind turbine blades. The thermodynamic models used to calculate de/anti-icing systems are also presented in a study by Fortin and Perron [18] on an airfoil NACA 63-415. The paper also includes a description of atmospheric icing, icing parameters and the different types of ice accretion, in addition to a review of the thermodynamic models used in ice accretion calculations for wind turbines and the numerical methods used for water droplet trajectory calculations and aerodynamic performance degradation [18]. The various published studies cited on wind turbine icing simulation were mainly up to quite recently on ice growth simulation. Of those, few studies integrate the modelling of electro-thermal IPS in their calculations [111]. In the last decade, ice accretion research has intensified on several techniques for ice prevention solutions. Comparisons between mitigation techniques, their executive design, verification and certification, advantages and disadvantages were systematically discussed in several studies [7,11,15,115,116,117,118] and Chapter 5, pp. 251–324 in [7]. A significant report by the Technical Research Centre of Finland (VTT) published in 2018 analyzed the performance and the maturity of wind turbines equipped with Ice Protection Systems for various icing climates. The report discussed IPS maturity from the viewpoint of availability and heating durations deviation analysis [112].

4. Conclusions

In this paper, a comprehensive review of wind turbine icing modelling is presented. The commonly applied approaches and the recent advances have been reported based on a systematic and concise literature review. The paper presents a panorama of the current modelling and simulation studies dealing with different aspects of ice accretion on wind turbines. The review of numerous CFD-based published studies on wind turbine icing during the last decade leads to the following considerations:

The most common approach uses Computational Fluid Dynamics (CFD). It treats multi-physics aspects including aerothermodynamics, thermodynamics, multiphase flows, heat and mass transfer and optimization theories. Several papers combine the CFD flow and icing simulations with the Blade Element Momentum Theory to generate the power curves for iced-up wind turbines. Some of these attempts were implemented using in-flight icing codes. In contrast, others were special-purpose codes, while most of them were merely methodologies developed using commercial computer-aided engineering software.

As previously mentioned, experimental studies require specialized measuring elements and a special design to analyze the effect of ice on wind turbines. This process is costly and, in some cases, not very accurate. Therefore, little information is available to validate the models proposed in recent years adequately. Thus, the authors generally validated with other numerical studies, other software, experimental data available for specific airfoils (NACA 0012 and S809, mainly), or carried out experimental studies.

Most of the research on wind turbine icing modelling was derived from the aeronautical industry, which has come a long way in this area. Following this progress in aeronautics, intensifying the modelling research on wind turbine icing, for example, by categorizing the wind turbine iced airfoils, could boost our comprehension of this phenomenon towards practical solutions. Following examples from aeronautics, while considering the particularities of wind turbine icing, was our guideline to make this study a unique reference for researchers in this domain. The aim is to suggest appropriate methods, references, and tools to conduct reliable icing modelling for wind turbines. This study can contribute to advancing the research on this phenomenon, common and frequent in Nordic countries, and to adapting wind turbines and optimizing their operation under icing conditions.

This entry is adapted from the peer-reviewed paper 10.3390/en14165207

This entry is offline, you can click here to edit this entry!