Bonded Marine Hoses for Floating Offshore Structures (FOS)

Bonded Marine Hoses for Floating Offshore Structures (FOS): Comparison

Please note this is a comparison between Version 3 by Yvaine Wei and Version 4 by Lindsay Dong.

By characterisation, a marine hose is a unique type of flexible riser used in fluid transfer. By definition, a marine hose is simply a fluid transfer conduit utilised in transferring, discharging, loading, and transporting fluids from an oil well to the platform of a floating platform or a floating structure. The fluid transfer system for bonded marine hoses is dependent on floating offshore structures (FOS). Single Point Mooring (SPM) systems are component aspects of the techno-economic design and FOS operation.

bonded marine hose
sustainable fluid transfer
single point mooring (SPM)
Catenary Anchor Leg Mooring (CALM)
buoy
Floating Offshore Structures (FOS)
offshore platform

1. Introduction

By definition, a marine hose is simply a fluid transfer conduit utilised in transferring, discharging, loading, and transporting fluids from an oil well to the platform of a floating platform or a floating structure ^[1][2][3]. These platforms could be an FPSO (Floating Production Storage and Offloading) vessel, a CALM (Catenary Anchor Leg Mooring) buoy, a SPAR (Single Point Anchor Reservoir), a floating semisubmersible, or a TLP (Tension Leg Platform), as depicted in Figure 1. However, due to the weight of the kill lines, marine hoses in chutes, reeling hoses on reel drums, marine risers, and other components on the deck, it is necessary to reduce the deck loads by using lighter and more sustainable materials/technologies. Thus, there is a need for lighter conduits and composite risers cum bonded marine hoses, to reduce the deck loads on CALM buoys, FPSOs and other offshore platforms (^{[4][5][6][7][8][9][10][11]}). The light weight makes it easier to store. Hence, it helps to create spaces on chutes, gangways, and storage racks. It also reduces the platform’s dead load.

Figure 1. Deep water facilities showing offshore platforms with the configurations for marine risers and mooring lines.

Recently, there has been a campaign in the marine industry for sustainable fluid transfer operations as one of the critical aspects of maritime and naval operations ^[12]. This development is in line with the UN SDG’s goal of sustainability.

Generally, floating offshore structures (FOS) are designed to be load-bearing, with connection components for both moorings and hose-risers. Examples of FOS include the Catenary Anchor Leg Mooring (CALM) buoys or Single Anchor Leg Mooring (SALM) buoys, the shuttle tankers or Floating Production Storage and Offloading (FPSO) vessels. The connection components include the bonded marine hoses, Hose End Valves (HEVs), Marine Breakaway Coupling (MBC), and Pipeline End Manifold (PLEM). Conversely, the ancillary components used in attaching the hoses to other hose sections or the tanker/buoy manifolds include the shackles, chain pick-up, and butterfly valves.

All these connection components are utilized on the marine hose via a variety of sustainable mooring methods, such as these three formations. The first form, also known as Multiple Buoy Mooring (MBM), typically consists of the following main components: mooring system with buoys, mooring legs and anchor points, pipeline end manifold (PLEM), pipeline to shore, subsea control system, and hose string with pick-up arrangement ^{[12][13][14][15]}. The many buoys are fastened to the seabed in a rectangular pattern with mooring lines and marine anchors, allowing safe mooring of a vessel positioned between the buoys with tug assistance. The bow of the ship is tied to the buoy surrounding it using both anchors or forward mooring buoys, while the stern is secured to the buoy around it using the stern and quarter mooring system. It keeps the ship in a fixed position and prevents it from weathervaning. The buoys serve as powerful anchor points for the vessel’s on-board mooring lines.

A launch crew takes the tanker lines one at a time and tows them to the numerous mooring buoys as soon as the tanker has approached into position with the help of tugs. The second form is the Single Point Mooring (SPM), which is an anchored loading buoy that acts as a mooring point and an interconnection for tankers loading or discharging liquid or gas contents. Figure 2 is a typical SPM terminal showing an SPM buoy and the Trelleborg’s floating hoses. The primary function of this SPM buoy is to maintain the vessel’s location concerning the buoy, keeping it in a stable position while allowing the vessels’ swinging responses to the ocean and wind ^[12].

Figure 2. SPM buoy hose system from the buoy to the shuttle tanker on an SPM Terminal (Provided by Trelleborg for this paper, and used with permission, Courtesy: Trelleborg).

2. Sustainable Fluid Transfer at SPM Mooring Terminals

2.1. Sustainable Fluid Transfer Operation

The fluid transfer system is at the heart of every SPM, as shown in Figure 2. The design parameters for this system mainly considers its safety for (un)loading operation and its usage for transporting products from the tanker to the seafloor PLEM (Pipeline End Manifold). To connect the hose to the tanker, some ancillary components have to be used, as shown in the tail end hose in Figure 3. It is important to state that a sustainable fluid transfer operation requires some components. These include the following:

Figure 3. Tanker end gear assembly for floating hose line configured using Yokohama’s Seaflex hose (adapted from Yokohama Manual).

The PLEM and the buoy are connected by flexible subsea hoses known as risers. The arrangement can take the form of a Chinese lantern, Lazy-S, Lazy Wave, or Steep-S depending on depth, sea state, buoy motions, and other factors.
The buoy is connected to the tanker by floating hose strings.
Marine breakaway coupling that enables for emergency pipeline disconnection to prevent hose/hawser breakage and associated oil spills.
The tanker can rotate with relation to the mooring buoy thanks to the product swivel, valves, and piping that connect the geostatic and rotating components of the buoy.

2.2. Preparation & Arrangement of SPM Moorings

On Single Buoy Mooring (SBM), the hawser is normally made up of nylon rope shackled to an integrated mooring uni-joint on the buoy deck. A chafing chain is attached to the tanker end of the hawser to prevent damage from the tanker fairlead. To measure hawser loads, a load pin can be attached to the mooring uni-joint on the buoy deck. Depending on the biggest size of vessel that would be anchored to the buoy, hawser systems use one or two ropes, as depicted in Figure 2 and Figure 4. Single-leg or grommet-leg ropes could be the type of ropes used. On the tanker side, these are frequently attached to an Oil Companies International Marine Forum (OCIMF) chafing chain. This can be either type A or B, depending on the maximum size of the tanker and the mooring loads. This chafe chain would then be secured in the tanker’s chain stopper.

Figure 4. Catenary Anchor Leg Mooring (CALM) Buoy hose system depicting Chinese-Lantern configuration and single point mooring (SPM).

To prepare the mooring for SPM deployment, the following steps are given:

For picking up rope, a messenger line has been requested.
It must be fitted in an empty drum at the bow, large enough to hold a 120 m [or longer, depending on terminal advice] Pick Up Rope.
The messenger must be 100 metres long (or as instructed by the terminal).
The messenger should be 1”−3” wide, and at its end have one small shackle.
The afterdeck specification to be used on the Tug Boat should be 02 × 200 Mt.

3. Model Application of Bonded Marine Hoses

Bonded marine hoses are for loading and offloading purposes. These hoses are used in a wide range of mooring systems. The circumstances under which they must operate also differ based on environmental conditions, size of the oil well, the water depth, the capacity of the terminal, the amount of hoses, the sizes of the hoses, the number of mooring chains (or mooring lines), the number of shuttle vessels, the schedule of daily operation, and the designed (un)loading system. Even within a single system, there are differences in the specifications of the many segments that make it up.

3.1. Configurations for Submarine Hoses

3.1.1. CALM Buoy Hose Configurations

The Catenary Anchor Leg Mooring (CALM) buoy system comprises a buoy with pivot, called the turntable. Sometimes, it is called the turret buoy or turntable buoy. Figure 4 shows the different configurations of Catenary Anchor Leg Mooring (CALM) buoy systems. The CALM buoy system has different connections, such as the mooring fairlead and hose manifold. The tanker is anchored to the turntable pivot, as it rotates around its vertical axis. The turntable is also connected to the floating hose through the hose manifold at an angle. The tanker is attached to the turntable and connected to the turntable’s floating hose strings. The mooring chains or anchor chains are used to moor the buoy as it aids in the buoy’s stability. A swivel transfers the fluid to the submarine hose strings connected to the undersea pipeline via the pipeline end manifold. The entire system can freely spin due to the forces applied by currents and waves, a phenomenon known as weathervaning. Figure 5 depicts an internal turret FPSO with multiple arrangements of marine hoses and flexible risers on an FPSO.

Figure 5. An internal turret FPSO with multiple marine hoses and flexible risers showing different configuration and the following components: modules, flowlines, flexible riser, subsea buoy, tether, PLEM, mooring lines, submarine hose, riser tether anchor, buoyancy modules and internal turret system.

3.1.2. Chinese-Lantern Hose Configurations

Underwater floats are tied to the hose string, which should keep its shape even under the harshest situations. To avoid concentrated bending strains, the hoses connecting to the pipeline end manifold should be strengthened at the attached end. A typical system for Chinese-lantern hose configuration is given in Figure 6.

Figure 6. An illustration of Chinese-lantern hose configuration.

3.1.3. Lazy-S Hose Configurations

To obtain the optimum hose arrangement, floatation in the form of bead floats or adjustable buoyancy tanks is given. This is done just to avoid kinking or wear upon this hose. A typical system for Lazy-S hose configuration is given in Figure 7.

Figure 7. An illustration of Lazy-S Hose Configuration.

3.1.4. Steep-S Hose Configurations

CALM buoys in water depths greater than 45 metres benefit from this design. The buoyancy tanks’ capacity must be sufficient to sustain positive buoyancy for hoses in both oil and water filled conditions. A typical system for Steep-S hose configuration is given in Figure 8.

Figure 8. An illustration of Steep-S hose configuration.

3.2. Configurations for Floating Hoses

3.2.1. SALM Buoy Hose Configurations

The SALM (Single Anchor Leg Mooring) system consists of a mooring buoy connected to a gravity or piling foundation by an anchor chain with a swivel for rotation, as in Figure 9. The tanker moors with one or more hawsers to the buoy in the CALM system, but the hose strings in the SALM system go directly to the pipeline end manifold. A fluid swivel is positioned concentrically around the anchor leg to allow fluid to pass through while rotating in reaction to the motions of the moored vessel. The fluid swivel is connected to the submarine hose string. The hose arm can be pivoted around the horizontal axis, allowing the angle at which the hose leaves the fluid swivel to vary, or it can be locked at a specific angle. The hose string might be shaped in an S-shape or can vertically and gradually curve towards the horizontal water plane. To achieve the correct shape, buoyancy must be used. Integral floatation or hose floats can be used to accomplish this. Integral floatation, on the other hand, does not work effectively in the presence of a substantial hydrostatic head. Between the submarine and the floating hoses, there must be enough buoyancy to prevent the floating hose from being pulled underwater. To spread the bending stresses caused by the transition between the undersea and floating hoses, hose pieces with reinforced ends must be employed.

Figure 9. Buoy systems showing (a) CALM and (b) SALM buoy systems.

3.2.2. Floating Tandem Mooring Hose Configurations

Tandem mooring is a technique for transporting oil and oil by-products from FSOs, FPSOs, FSUs, FSRUs, and other extraction facilities to shuttle tankers. It can be floating or submerged, and it can be hung from the ship’s side or wound around a reel. A retention rope and revolving spool component secure the string to the vessel, resulting in the “Goose-Neck” design. Depending on the environmental circumstances, a floating or submarine string can be used. In some circumstances, the oil is extracted from the well using a Floating Production Storage and Offloading (FPSO) system. As shown in Figure 10, these ships are anchored with a turret and anchor lines. The arrangement of the tandem mooring given in Table 1 is for the hose positions in Figure 10.

Figure 10. Tandem mooring floating hose configuration.

Table 1. Arrangement of tandem mooring floating hoses.

No.	Location	Description	Hose Type	Optional Type	Characteristics	Application

Figure 13. Deepwater Export Line showing (a) typical offloading line (OOL) called Trelleborg’s trelline and gimbal with spread moorings, and (b) Pazflor OOL configuration. It shows the deepwater OOL array used as: 1 hose end, 38 hoses with collars having fewer buoyancy modules, 5 hoses with collars having fewer buoyancy modules, 45 hoses with collars having fewer buoyancy modules, 5 hoses with collars having fewer buoyancy modules, 38 hoses with collars having fewer buoyancy modules (Adapted, Courtesy: Trelleborg).

Abbreviations

CALM	Catenary Anchor Leg Mooring
FPSO	Floating Production Storage and Offloading
FSO	Floating Storage and Offloading
FSRU	Floating Storage and Regasification Unit
FSU	Floating Storage Unit
HEV	Hose End Valves
MBC	Marine Breakaway Coupling
MBM	Multi Buoy Mooring (or Multiple Buoy Mooring)
OCIMF	Oil Companies International Marine Forum
PLEM	Pipeline End Manifold
SALM	Single Anchor Leg Mooring
SBM	Single Buoy Mooring
SDG	Sustainable Development Goals
SPAR	Single Point Anchor Reservoir
SPM	Single Point Mooring
TLP	Tension Leg Platform
UN	United Nation

1	FPSO Connection	Off take connection	Floating	Reel	Reinforced hose end, at one end	Connected to shuttle tanker bow loading point or FPSO
2	Reduced Buoyancy	Reducer	Floating	Reel	Reduced buoyancy or Neutral	Often next to 2–3 hose sections on the string
3	Mainline	Mainline	Floating	Reel	Fairly flexible	Main part of the floating hose string
4	Operational Taper	Taper	Floating	Reel	Integral reducing bore	Connection of smaller bore tail hose and larger bore mainline
5	Tail	Tail Hose	Floating	Reel	Electrically discontinuous	Smaller bore diameter compared to mainline. Links tanker end to handle rail hose
6	Rail	Rail Hose	Floating Rail	Reel	Higher flexibility during lug lifting	Over rail hose for connecting to the manifolds of conventional midships

3.2.3. Stored Hose (or Hose Reel) Tandem Mooring

The mooring is done in a tandem configuration once more. However, the hose is employed as an in-air catenary, floating on the water, as shown in Figure 11. When not in use, the offloading hose is stored on the FPSO in a chute (as seen in Figure 11) or on a hose reel (as seen in Figure 12). The goal of the reeling hose configuration is to be able to recover and store the hose on the FPSO during bad weather. Hoses of this type must have a high flexibility reserve, bend radius tolerance, and axial strength. In the event of an emergency release, the catenary design also has intrinsic buoyancy, ensuring that the hose string is not lost, even when filled with water.

Figure 11. Two different hose storage systems in the chutes of floating FPSOs, showing (a) loading hose stowed on deck’s chute along the FPSO’s wall, which could also be a free-hanging catenary hose, and (b) loading hose stowed in the chute on a lower area of FPSO’s deck inside its deck trays between loadings, with the hose string winched onboard over a stern roller chute.

Figure 12. Offshore reeling hose stored on the reel-drum showing reel, Marine Breakaway Coupling (MBC) and Hose End Valve (HEV).

3.2.4. Deepwater Export Lines

Spread mooring is frequently employed instead of a turret mooring system in projects having locations with relatively light environmental conditions. The issue this creates is that, due to the practicalities resulting from the large expanse of seawater required, it consumes more resources. In addition, the FPSO’s fixed position and the tandem mooring with the shuttle tanker make it quite challenging to achieve. Typical materials for such deepwater export lines have been reported by Trelleborg ^{[16][17][18][19][20]}. A deepwater export connection to a CALM buoy, where the shuttle tanker moors, could be one possibility ^[18][19][20], as in Figure 13. The tankers may weathervane here without having to worry about colliding with the FPSO. The hose’s deepest point is generally between 200 m and 300 m deep.

References

Charlesworth, D.; D’All, B.; Zimmerlin, C.; Remita, E.; Langhelle, N.; Wang, T. Operational experience of the fatigue performance of a flexible riser with a flooded annulus. In Proceedings of the Offshore Technology Conference (OTC), Rio de Janeiro, Brazil, 4–6 October 2011. Paper Presented at the OTC: Brasil.
Dahl, C.S.; Andersen, B.A.M.; Gronne, M. Developments in managing flexible risers and pipelines, a suppliers perspective. In Proceedings of the Offshore Technology Conference, Houston, TX, USA, 2–5 May 2011.
Obrien, P.; Meldrum, E.; Overton, C.; Picksley, J.; Anderson, K.; MacLeod, I. Outcomes from the SureFlex joint industry project—An international initiative on flexible pipe integrity assurance. In Proceedings of the Offshore Technology Conference, Houston, TX, USA, 2–5 May 2011.
Amaechi, C.V. Numerical investigation on mooring line configurations of a Paired Column Semisubmersible for its global performance in deep water condition. Ocean Eng. 2021, in press.
Amaechi, C.V. Dynamic analysis of tensioner model applied on global response with marine riser recoil and disconnect. Ocean Eng. 2021, in press.
Amaechi, C.V. Parametric investigation on tensioner stroke analysis, recoil analysis and disconnect for the marine drilling riser of a Paired Column Semisubmersible under deep water waves. Ocean Eng. 2021, in press.
Amaechi, C.V.; Chesterton, C.; Butler, H.O.; Wang, F.; Ye, J. Review on the design and mechanics of bonded marine hoses for Catenary Anchor Leg Mooring (CALM) buoys. Ocean. Eng. 2021, 242, 110062.
Amaechi, C.V.; Wang, F.; Ye, J. Mathematical modelling of marine bonded hoses for single point mooring (SPM) systems, with catenary anchor leg mooring (CALM) buoy application—A review. J. Mar. Sci. Eng. 2021, 9, 1179.
Amaechi, C.V.; Wang, F.; Ye, J. Numerical assessment on the dynamic behaviour of submarine hoses attached to CALM buoy configured as lazy-S under water waves. J. Mar. Sci. Eng. 2021, 9, 1130.
Amaechi, C.V. Numerical studies on CALM buoy motion responses and the effect of buoy geometry cum skirt dimensions with its hydrodynamic waves-current interactions. Ocean Eng. 2021, in press.
Amaechi, C.V. Investigation on hydrodynamic characteristics, wave-current interaction, and sensitivity analysis of submarine hoses attached to a CALM buoy. J. Mar. Sci. Eng. 2021, 9. in press.
Rutkowski, G. A Comparison between conventional buoy mooring CBM, single point mooring SPM and single anchor loading SAL systems considering the hydro-meteorological condition limits for safe ship’s operation offshore. TransNav Int. J. Mar. Navig. Saf. Sea Transp. 2019, 13, 187–195.
Amaechi, C.V. Novel Design, Hydrodynamics and Mechanics of Marine Hoses for Oil/Gas Applications. Ph.D. Thesis, Lancaster University, Lancaster, UK, 2021.
Amaechi, C.V.; Wang, F.; Hou, X.; Ye, J. Strength of submarine hoses in Chinese-lantern configuration from hydrodynamic loads on CALM buoy. Ocean Eng. 2019, 171, 429–442.
Amaechi, C.V.; Ye, J.; Hou, X.; Wang, F.-C. Sensitivity studies on offshore submarine hoses on CALM buoy with comparisons for Chinese-lantern and lazy-S configuration OMAE2019-96755. In Proceedings of the 38th International Conference on Ocean, Offshore and Arctic Engineering, Glasgow, UK, 9–14 June 2019.
Trelleborg. Surface Buoyancy Brochure; Report BC-SUR-v1.3-EN; Trelleborg: Trelleborg, Sweden, 2017; pp. 1–24. Available online: https://www.trelleborg.com/en/marine-and-infrastructure/products-solutions-and-services/marine/surface-buoyancy (accessed on 25 October 2021).
Trelleborg. Oil & Gas Solutions: Oil & Gas Hoses for Enhanced Fluid Transfer Solutions; Trelleborg: Clemont-Ferrand, France, 2016.
Rampi, L.; Lavagna, P.; Mayau, D. TRELLINE? A cost-effective alternative for oil offloading lines (OOLs). In Proceedings of the Offshore Technology Conference, Houston, TX, USA, 1–4 May 2006.
Prischi, N.; Mazuet, F.; Frichou, A.; Lagarrigue, V. SS-offshore offloading systems and operations bonded flexible oil offloading lines, a cost effective alternative to traditional oil offloading lines. In Proceedings of the Offshore Technology Conference, Houston, TX, USA, 30 April–3 May 2012.
Mayau, D.; Rampi, L. Trelline—A new flexible deepwater offloading line (OLL). In Proceedings of the Sixteenth International Offshore and Polar Engineering Conference, San Francisco, CA, USA, 28 May–2 June 2006; Available online: https://onepetro.org/ISOPEIOPEC/proceedings-abstract/ISOPE06/All-ISOPE06/ISOPE-I-06-127/9875 (accessed on 12 October 2021).