Potential of Energy Harvesting Sources in Electric Vehicles: Comparison
Please note this is a comparison between Version 3 by Dean Liu and Version 2 by Dean Liu.

Energy harvesting, a cutting-edge technology that captures wasted energy from vehicles, constitutes a means to improve the efficiency of electric vehicles. Dissipated energy can be converted into electricity using regenerative energy recovery systems and put to various uses.

  • electric vehicle
  • energy harvesting
  • thermal energy
  • mechanical energy

1. Potential Energy Sources

In an electric vehicle, energy is stored in the battery, which functions as the vehicle’s primary power source (Figure 1). The battery is used to power the electric motor, which drives the wheels and propels the car forward [1]. However, some of the energy stored in the battery is dissipated or lost in various sections of the vehicle due to thermal or vibrational causes. These losses can be collected and recycled as alternative energy sources, increasing the total efficiency of the electric vehicle. The interaction between the ground and the wheel, the braking system, the shock absorber, the electric motor and battery, and the aerodynamic drag are all possible sources for energy recovery. These energy sources are depicted in a diagram that illustrates the flow of energy from the battery used in an electric car. The aim of energy recovery is to convert these losses into usable energy that can then be reused to power the vehicle or stored in the battery for later use.
Figure 1. Energy flow in electric vehicle.
Energy flows from the battery to the electric motor, which then converts this electrical energy into mechanical energy to drive the wheels in an electric car. The electric motor is driven by an inverter, which converts the direct current (DC) from the battery to the alternating current (AC) required by the motor. When the vehicle is braking or coasting, the electric engine can function as a generator, converting some of the vehicle’s kinetic energy back into electrical energy. This energy is then stored in the battery and used to power the engine later. Furthermore, the vehicle may have auxiliary systems that require electrical energy to function, such as air conditioning or heating. This energy is derived from the battery as well. In summary, energy flows from the battery to the electric motor in an electric car, with energy captured during braking or coasting and used to recharge the battery.

2. Interaction Ground–Wheel

In a vehicle, the interaction between the ground and the wheel creates a major source of energy loss. Rolling resistance is the force that resists the direction of movement the tire makes on the traction surface during this interaction. Rolling resistance is caused by deformation in the tire when it comes into contact with the ground, and results in a loss of mechanical energy. Fortunately, using suitable technologies, this energy can be captured and transformed into a new source of energy and adding to efficiency. The tire, as the final component of the driveline, is critical in this respect [2]. The study of mechanical energy loss through contact has been a topic of interest for researchers, who aim to find ways to harness this energy for practical use [3].

3. Braking System

Various studies [4] have recorded the conversion of kinetic energy into thermal energy caused by the friction between the brake disc and pads during the braking process. These studies have recorded a wide range of braking temperatures, with temperatures as low as 150 °C reported in works such as [5][6]. Temperatures between 150 °C and 300 °C have been measured by others, including [7][8][9][10][11][12], while temperatures above 300 °C have been documented by [13][14][15][16]. Furthermore, braking can cause triboelectrification, which provides another possible source of recoverable energy [17]. As a result, the energy recovered from the braking mechanism can be divided into two types: thermal energy and triboelectric energy.

4. Shock Absorber

Another form of energy loss in a vehicle that can be recovered is that of the shock absorber. The shock absorber is critical in delivering a comfortable ride and maintaining vehicle stability. It absorbs road bumps and vibrations, reducing the discomfort for passengers and wear on vehicle components. Because of its internal hydraulic resistance, the shock absorber transforms kinetic energy into heat energy. This heat energy can be recovered and converted into power. Through the piezoelectric effect, the shock absorber can also be used as a power source. The piezoelectric effect is the generation of an electric charge because of mechanical tension exerted on certain materials. As a result, the shock absorber can be integrated into a vehicle as a piezoelectric energy harvester. The car suspension facilitates the transmission of force and torque between the vehicle body and wheels. The automobile suspension, a key component that supports both the vehicle body and the wheels, helps to mitigate the impact caused by uneven road surfaces and guarantees a pleasant driving experience in the vehicle body [18]. Both the tires and the vehicle suspension usually absorb vibrational energy, though the tires only absorb a small amount due to their limited damping ability. The suspension absorbs and dissipates the main amount of vibrational energy [19].

5. Electric Motor and Battery

The main source of power in an electric vehicle is the electric motor. The motor converts the electrical energy from the battery into mechanical energy that propels the car. However, this process is not completely efficient, and some of the electrical energy from the battery is wasted as heat or sound. Furthermore, the battery suffers energy losses due to internal resistance and temperature changes, which impact the capacity. Consequently, the losses from an electric vehicle motor and battery are potential sources of energy that can be recovered and used for other purposes. The heat produced by the battery and electric motor can be used as a source of thermal energy. Several investigations have shown that these components contain heat. Battery temperatures below 40 °C have been reported in references [20][21][22][23][24][25][26][27]. Meanwhile, studies such as [28][29][30][31][32][33][34][35] measured temperatures ranging from 40 °C to 60 °C, with [36][37] recording temperatures higher than 60 °C. Temperature changes in electric motors can be classified into three groups: less than 50 °C, as seen in [38], between 50 °C and 100 °C, as seen in [39][40][41][42][43][44][45] and above 100 °C, as seen in [46][47][48][49][50][51].The reviews state that operating temperatures of Li-ion batteries typically range from −20 °C to 60 °C, with an ideal range of 20 °C to 40 °C for optimal performance and lifespan. The authors also note that temperature management is critical for preventing thermal runaway and ensuring safe operation of the battery system. Overall, the review supports the idea that careful temperature management is essential for the optimal performance, safety, and lifespan of electric vehicle batteries, and highlights the importance of ongoing research and innovation in battery thermal management to improve the efficiency and sustainability of electric vehicles.

6. Aerodynamic Drag Source

Aerodynamic drag is the resistance to motion produced by the air that surrounds a vehicle. It is a significant contributor to vehicle fuel usage and is caused by the interaction between the vehicle and the air it moves through. Aerodynamic drag can be decreased by streamlining the vehicle shape, reducing its frontal area, and optimizing its body design to minimize airflow turbulence. This reduction in drag results in less energy loss, which leads to lower fuel usage and lower emissions. Engineers can optimize the aerodynamic drag of a vehicle to reduce its effect on fuel consumption by controlling the airflow over the vehicle surface and through the underbody.
Aerodynamic drag happens when a vehicle is in motion and encounters resistance from the air relative to its speed. This opposing force, which causes a loss of momentum, can significantly affect vehicle fuel consumption and emissions. To offset this, aerodynamic drag can be reduced or captured [49]. Recovering and utilizing this dynamic energy would be an asset for improving the total energy efficiency in an electric vehicle.

7. Applicable Technologies

Figure 2 shows the two major forms of energy that can be recovered from an electric vehicle: thermal energy and mechanical energy. There are specific technologies available to successfully recover these sources of energy, which have different levels of efficiency and have undergone simulation or experimental testing.
Energies 16 05193 g003 550

References

  1. Sanguesa, J.A.; Torres-Sanz, V.; Garrido, P.; Martinez, F.J.; Marquez-Barja, J.M. A Review on Electric Vehicles: Technologies and Challenges. Smart Cities 2021, 4, 372–404.
  2. Farhadi, P.; Golmohammadi, A.; Malvajerdi, A.S.; Shahgholi, G. Tire and soil effects on power loss: Measurement and comparison with finite element model results. J. Terramechanics 2020, 92, 13–22.
  3. Guo, T.; Liu, G.; Pang, Y.; Wu, B.; Xi, F.; Zhao, J.; Bu, T.; Fu, X.; Li, X.; Zhang, C. Compressible hexagonal-structured triboelectric nanogenerators for harvesting tire rotation energy. Extrem. Mech. Lett. 2018, 18, 1–8.
  4. Belhocine, A.; Abdullah, O.I. Finite element analysis (FEA) of frictional contact phenomenon on vehicle braking system. Mech. Based Des. Struct. Mach. 2022, 50, 2961–2996.
  5. Han, M.J.; Lee, C.H.; Park, T.W.; Park, J.M.; Son, S.M. Coupled thermo-mechanical analysis and shape optimization for reducing uneven wear of brake pads. Int. J. Automot. Technol. 2017, 18, 1027–1035.
  6. Zum Hagen, F.H.F.; Mathissen, M.; Grabiec, T.; Hennicke, T.; Rettig, M.; Grochowicz, J.; Vogt, R.; Benter, T. Study of Brake Wear Particle Emissions: Impact of Braking and Cruising Conditions. Environ. Sci. Technol. 2019, 53, 5143–5150.
  7. Liu, H.; Wen, C.; Yuen, A.C.Y.; Han, Y.; Cheung, S.C.-P.; Kook, S.; Yeoh, G.H. A novel thermal management system for battery packs in hybrid electrical vehicles utilising waste heat recovery. Int. J. Heat Mass Transf. 2022, 195, 123199.
  8. Riva, G.; Perricone, G.; Wahlström, J. A Multi-Scale Simulation Approach to Investigate Local Contact Temperatures for Commercial Cu-Full and Cu-Free Brake Pads. Lubricants 2019, 7, 80.
  9. Borawski, A. Simulation Study of the Process of Friction in the Working Elements of a Car Braking System at Different Degrees of Wear. Acta Mech. Autom. 2018, 12, 221–226.
  10. Eriksson, M.; Bergman, F.; Jacobson, S. Surface Characterization of Brake Pads after Running Under Silent and Squealing Conditions. Wear 1999, 232, 163–167.
  11. Ricciardi, V.; Travagliati, A.; Schreiber, V.; Klomp, M.; Ivanov, V.; Augsburg, K.; Faria, C. A Novel Semi-Empirical Dynamic Brake Model for Automotive Applications. Tribol. Int. 2020, 146, 106223.
  12. Tauviqirrahman, M.; Muchammad, M.; Setiazi, T.; Setiyana, B.; Jamari, J. Analysis of the effect of ventilation hole angle and material variation on thermal behavior for car disc brakes using the finite element method. Results Eng. 2023, 17, 100844.
  13. Borawski, A. Research in Impact of Cargo Vehicle Load Weight on Braking System Element Heating Process in Single Emergency Stopping. In Proceedings of the 19th International Scientific Conference Engineering for Rural Development, Latvia, Jelgava, 20–22 May 2020; pp. 578–584.
  14. Polajnar, M.; Kalin, M.; Thorbjornsson, I.; Thorgrimsson, J.; Valle, N.; Botor-Probierz, A. Friction and wear performance of functionally graded ductile iron for brake pads. Wear 2017, 382–383, 85–94.
  15. Belhocine, A.; Bouchetara, M. Thermomechanical modelling of dry contacts in automotive disc brake. Int. J. Therm. Sci. 2012, 60, 161–170.
  16. Grzes, P. Maximum temperature of the disc during repeated braking applications. Adv. Mech. Eng. 2019, 11, 1687814019837826.
  17. Han, C.B.; Du, W.; Zhang, C.; Tang, W.; Zhang, L.; Wang, Z.L. Harvesting energy from automobile brake in contact and non-contact mode by conjunction of triboelectrication and electrostatic-induction processes. Nano Energy 2014, 6, 59–65.
  18. Wu, W.; Zhang, S.; Zhang, Z. Mathematical Simulations and On-Road Experimentations of the Vibration Energy Harvesting from Mining Dump Truck Hydro-Pneumatic Suspension. Shock Vib. 2019, 2019, 4814072.
  19. Zhang, Y.; Guo, K.; Wang, D.; Chen, C.; Li, X. Energy conversion mechanism and regenerative potential of vehicle suspensions. Energy 2017, 119, 961–970.
  20. Han, X.; Zou, H.; Tian, C.; Tang, M.; Yan, Y. Numerical study on the heating performance of a novel integrated thermal management system for the electric bus. Energy 2019, 186, 115812.
  21. Ding, P.; Wang, Z.; Wang, Y.; Li, K. A distributed multiple-heat source staged heating method in an electric vehicle. Renew. Energy 2020, 150, 1010–1018.
  22. Al-Zareer, M.; Dincer, I.; Rosen, M.A. Novel thermal management system using boiling cooling for high-powered lithium-ion battery packs for hybrid electric vehicles. J. Power Sources 2017, 363, 291–303.
  23. Zhang, Y.; Liang, F.; Li, S.; Zhang, C.; Zhang, S.; Liu, X.; Zhao, S.; Yang, S.; Xia, Y.; Lin, J.; et al. A review on battery thermal management and its digital improvement-based cyber hierarchy and interactional network. Int. J. Energy Res. 2022, 46, 11529–11555.
  24. Ahn, J.H.; Kang, H.; Lee, H.S.; Jung, H.W.; Baek, C.; Kim, Y. Heating performance characteristics of a dual source heat pump using air and waste heat in electric vehicles. Appl. Energy 2014, 119, 1–9.
  25. Maral, Y.; Aktas, M.; Erol, O.; Ongun, R.; Polat, F. An examination about thermal capacities of thermoelectric coolers in battery cooling systems. J. Eng. Res. 2017, 6, 703–710.
  26. Liu, Y.; Yang, S.; Guo, B.; Deng, C. Numerical analysis and design of thermal management system for lithium ion battery pack using thermoelectric coolers. Adv. Mech. Eng. 2014, 6, 852712.
  27. Feng, L.; Zhou, S.; Li, Y.; Wang, Y.; Zhao, Q.; Luo, C.; Wang, G.; Yan, K. Experimental investigation of thermal and strain management for lithium-ion battery pack in heat pipe cooling. J. Energy Storage 2018, 16, 84–92.
  28. Lan, C.; Xu, J.; Qiao, Y.; Ma, Y. Thermal management for high power lithium-ion battery by minichannel aluminum tubes. Appl. Therm. Eng. 2016, 101, 284–292.
  29. Zou, H.; Wang, W.; Zhang, G.; Qin, F.; Tian, C.; Yan, Y. Experimental investigation on an integrated thermal management system with heat pipe heat exchanger for electric vehicle. Energy Convers. Manag. 2016, 118, 88–95.
  30. Smith, J.; Hinterberger, M.; Schneider, C.; Koehler, J. Energy savings and increased electric vehicle range through improved battery thermal management. Appl. Therm. Eng. 2016, 101, 647–656.
  31. Lyu, Y.; Siddique, A.; Majid, S.; Biglarbegian, M.; Gadsden, S.; Mahmud, S. Electric vehicle battery thermal management system with thermoelectric cooling. Energy Rep. 2019, 5, 822–827.
  32. Wiriyasart, S.; Hommalee, C.; Sirikasemsuk, S.; Prurapark, R.; Naphon, P. Thermal management system with nanofluids for electric vehicle battery cooling modules. Case Stud. Therm. Eng. 2020, 18, 100583.
  33. Liu, F.; Lan, F.; Chen, J. Dynamic thermal characteristics of heat pipe via segmented thermal resistance model for electric vehicle battery cooling. J. Power Sources 2016, 321, 57–70.
  34. Hu, C.; Li, H.; Wang, Y.; Hu, X.; Tang, D. Experimental and numerical investigations of lithium-ion battery thermal management using flat heat pipe and phase change material. J. Energy Storage 2022, 55 Pt D, 105743.
  35. Rao, Z.; Qian, Z.; Kuang, Y.; Li, Y. Thermal performance of liquid cooling based thermal management system for cylindrical lithium-ion battery module with variable contact surface. Appl. Therm. Eng. 2017, 123, 1514–1522.
  36. Zhao, J.; Rao, Z.; Huo, Y.; Liu, X.; Li, Y. Thermal management of cylindrical power battery module for extending the life of new energy electric vehicles. Appl. Therm. Eng. 2015, 85, 33–43.
  37. Tian, Z.; Gan, W.; Zhang, X.; Gu, B.; Yang, L. Investigation on an integrated thermal management system with battery cooling and motor waste heat recovery for electric vehicle. Appl. Therm. Eng. 2018, 136, 16–27.
  38. Tian, Z.; Gu, B.; Gao, W.; Zhang, Y. Performance evaluation of an electric vehicle thermal management system with waste heat recovery. Appl. Therm. Eng. 2020, 169, 114976.
  39. Huang, J.; Shoai Naini, S.; Miller, R.; Rizzo, D.; Sebeck, K.; Shurin, S.; Wagner, J. A Hybrid Electric Vehicle Motor Cooling System-Design, Model, and Control. IEEE Trans. Veh. Technol. 2019, 68, 4467–4478.
  40. Sun, B.; Gao, S.; Ma, C.; Li, J. System power loss optimization of electric vehicle driven by front and rear induction motors. Int. J. Automot. Technol. 2018, 19, 121–134.
  41. Liu, X.; Zheng, C.; Liu, C.; Pong, P.W.T. Experimental Investigation of a Johnson Noise Thermometry Using GMR Sensor for Electric Vehicle Applications. IEEE Sens. J. 2018, 18, 3098–3107.
  42. Chen, Q.; Yang, X. Calculation analysis of thermal loss and temperature field of in-wheel motor in micro-electric vehicle. J. Mech. Sci. Technol. 2014, 28, 3189–3195.
  43. Huang, J.L.; Xuan, Y.; Zhang, L.; Liu, T.G. Analysis on the design and temperature field of switched reluctance motor for electric vehicle. J. Phys. Conf. Ser. 2021, 1777, 012001.
  44. Li, L.; Zhu, G.; Zhao, Y.; Jia, N.; Xue, M.; Li, Y. Design and analysis of different cooling schemes of a flux-modulated permanent magnet in-wheel motor for electric vehicle applications. IET Electr. Power Appl. 2021, 15, 348–358.
  45. Wang, X.; Li, B.; Gerada, D.; Huang, K.; Stone, I.; Worrall, S.; Yan, Y. A critical review on thermal management technologies for motors in electric cars. Appl. Therm. Eng. 2022, 201. (Part A).
  46. Putra, N.; Ariantara, B. Electric motor thermal management system using L-shaped flat heat pipes. Appl. Therm. Eng. 2017, 126, 1156–1163.
  47. Lee, K.-H.; Cha, H.-R.; Kim, Y.-B. Development of an interior permanent magnet motor through rotor cooling for electric vehicles. Appl. Therm. Eng. 2016, 95, 348–356.
  48. Naini, S.S.; Miller, R.S.; Rizoo, D.; Wagner, J. A Model Reference Adaptive Controller for an Electric Motor Thermal Management System in Autonomous Vehicles. SAE Int. J. Electrified Veh. 2022, 12, 3–16.
  49. Chen, Q.; Shao, H.; Huang, J.; Sun, H.; Xie, E.J. Analysis of Temperature Field and Water Cooling of Outer Rotor In-Wheel Motor for Electric Vehicle. IEEE Access 2019, 7, 140142–140151.
  50. Gai, Y.; Kimiabeigi, M.; Chong, Y.C.; Widmer, J.D.; Deng, X.; Popescu, M.; Goss, J.; Staton, D.A.; Steven, A. Cooling of automotive traction motors: Schemes, examples, and computation methods. IEEE Trans. Ind. Electron. 2019, 66, 1681–1692.
  51. Guo, F.; Zhang, C. Oil-cooling method of the permanent magnet synchronous motor for electric vehicle. Energies 2019, 12, 2984.
More