1. Definition

In surveying and geodesy, a datum is a reference system or an approximation of the Earth's surface against which positional measurements are made for computing locations. Horizontal datums are used for describing a point on the Earth's surface, in latitude and longitude or another coordinate system. Vertical datums are used to measure elevations or underwater depths.

1.1. Horizontal Datum

The horizontal datum is the model used to measure positions on the Earth. A specific point on the Earth can have substantially different coordinates, depending on the datum used to make the measurement. There are hundreds of local horizontal datums around the world, usually referenced to some convenient local reference point. Contemporary datums, based on increasingly accurate measurements of the shape of the Earth, are intended to cover larger areas. The WGS 84 datum, which is almost identical to the NAD83 datum used in North America and the ETRS89 datum used in Europe, is a common standard datum.

For example, in Sydney there is a 200 metres (700 feet) difference between GPS coordinates configured in GDA (based on global standard WGS 84) and AGD (used for most local maps), which is an unacceptably large error for some applications, such as surveying or site location for scuba diving.^[1]

1.2. Vertical Datum

A vertical datum is a reference surface for vertical positions, such as the elevations of Earth features including terrain, bathymetry, water level, and man-made structures.

2. Geodetic Coordinates

The same position on a spheroid has a different angle for latitude depending on whether the angle is measured from the normal line segment CP of the ellipsoid (angle α) or the line segment AP from the center (angle β). Note that the "flatness" of the spheroid (orange) in the image is greater than that of the Earth; as a result, the corresponding difference between the "geodetic" and "geocentric" latitudes is also exaggerated. https://handwiki.org/wiki/index.php?curid=2060385

In geodetic coordinates, the Earth's surface is approximated by an ellipsoid, and locations near the surface are described in terms of latitude ([math]\displaystyle{ \phi }[/math]), longitude ([math]\displaystyle{ \lambda }[/math]), and height ([math]\displaystyle{ h }[/math]).^[2]

2.1. Geodetic versus Geocentric Latitude

Geodetic latitude and geocentric latitude represent similar quantities with different definitions. Geodetic latitude is defined as the angle between the equatorial plane and the surface normal at a point on the ellipsoid, whereas geocentric latitude is defined as the angle between the equatorial plane and a radial line connecting the centre of the ellipsoid to a point on the surface (see figure). When used without qualification, the term latitude refers to geodetic latitude. For example, the latitude used in geographic coordinates is geodetic latitude. The standard notation for geodetic latitude is φ. There is no standard notation for geocentric latitude; examples include θ, ψ, φ′.

Similarly, geodetic altitude is defined as the height above the ellipsoid surface, normal to the ellipsoid; whereas geocentric altitude is defined as the height above the ellipsoid surface along a line to the center of the ellipsoid (the radius). When used without qualification, the term altitude refers to geodetic altitude; as is used in aviation. Geocentric altitude is typically used in orbital mechanics.

3. Earth Reference Ellipsoid

3.1. Defining and Derived Parameters

The ellipsoid is completely parameterised by the semi-major axis [math]\displaystyle{ a }[/math] and the flattening [math]\displaystyle{ f }[/math].

From [math]\displaystyle{ a }[/math] and [math]\displaystyle{ f }[/math] it is possible to derive the semi-minor axis [math]\displaystyle{ b }[/math], first eccentricity [math]\displaystyle{ e }[/math] and second eccentricity [math]\displaystyle{ e' }[/math] of the ellipsoid

3.2. Parameters for Some Geodetic Systems

The two main reference ellipsoids used worldwide are the GRS80^[3] and the WGS84.^[4]

Geodetic Reference System 1980 (GRS80)

World Geodetic System 1984 (WGS 84)

The Global Positioning System (GPS) uses the World Geodetic System 1984 (WGS 84) to determine the location of a point near the surface of the Earth.

4. Conversion Calculations

Datum conversion is the process of converting the coordinates of a point from one datum system to another. Datum conversion may frequently be accompanied by a change of grid projection.

5. Discussion and Examples

A geodetic reference datum is a known and constant surface which is used to describe the location of unknown points on the Earth. Since reference datums can have different radii and different center points, a specific point on the Earth can have substantially different coordinates depending on the datum used to make the measurement. There are hundreds of locally developed reference datums around the world, usually referenced to some convenient local reference point. Contemporary datums, based on increasingly accurate measurements of the shape of the Earth, are intended to cover larger areas. The most common reference Datums in use in North America are NAD27, NAD83, and WGS 84.

The North American Datum of 1927 (NAD 27) is "the horizontal control datum for the United States that was defined by a location and azimuth on the Clarke spheroid of 1866, with origin at (the survey station) Meades Ranch (Kansas)." ... The geoidal height at Meades Ranch was assumed to be zero, as sufficient gravity data was not available, and this was needed to relate surface measurements to the datum. "Geodetic positions on the North American Datum of 1927 were derived from the (coordinates of and an azimuth at Meades Ranch) through a readjustment of the triangulation of the entire network in which Laplace azimuths were introduced, and the Bowie method was used." (http://www.ngs.noaa.gov/faq.shtml#WhatDatum ) NAD27 is a local referencing system covering North America.

The North American Datum of 1983 (NAD 83) is "The horizontal control datum for the United States, Canada, Mexico, and Central America, based on a geocentric origin and the Geodetic Reference System 1980 (GRS80). "This datum, designated as NAD 83 ...is based on the adjustment of 250,000 points including 600 satellite Doppler stations which constrain the system to a geocentric origin." NAD83 may be considered a local referencing system.

WGS 84 is the World Geodetic System of 1984. It is the reference frame used by the U.S. Department of Defense (DoD) and is defined by the National Geospatial-Intelligence Agency (NGA) (formerly the Defense Mapping Agency, then the National Imagery and Mapping Agency). WGS 84 is used by DoD for all its mapping, charting, surveying, and navigation needs, including its GPS "broadcast" and "precise" orbits. WGS 84 was defined in January 1987 using Doppler satellite surveying techniques. It was used as the reference frame for broadcast GPS Ephemerides (orbits) beginning January 23, 1987. At 0000 GMT January 2, 1994, WGS 84 was upgraded in accuracy using GPS measurements. The formal name then became WGS 84 (G730), since the upgrade date coincided with the start of GPS Week 730. It became the reference frame for broadcast orbits on June 28, 1994. At 0000 GMT September 30, 1996 (the start of GPS Week 873), WGS 84 was redefined again and was more closely aligned with International Earth Rotation Service (IERS) frame ITRF 94. It was then formally called WGS 84 (G873). WGS 84 (G873) was adopted as the reference frame for broadcast orbits on January 29, 1997.^[5] Another update brought it to WGS84(G1674).

The WGS 84 datum, within two meters of the NAD83 datum used in North America, is the only world referencing system in place today. WGS 84 is the default standard datum for coordinates stored in recreational and commercial GPS units.

Users of GPS are cautioned that they must always check the datum of the maps they are using. To correctly enter, display, and to store map related map coordinates, the datum of the map must be entered into the GPS map datum field.

5.1. Examples

Examples of map datums are:

• WGS 84, 72, 66 and 60 of the World Geodetic System
• NAD83, the North American Datum which is very similar to WGS 84
• NAD27, the older North American Datum, of which NAD83 was basically a readjustment [1]
• OSGB36 of the Ordnance Survey of Great Britain
• ETRS89, the European Datum, related to ITRS
• ED50, the older European Datum
• GDA94, the Australian Datum^[6]
• JGD2011, the Japanese Datum, adjusted for changes caused by 2011 Tōhoku earthquake and tsunami^[7]
• Tokyo97, the older Japanese Datum^[8]
• KGD2002, the Korean Datum^[9]
• TWD67 and TWD97, different datum currently used in Taiwan.^[10]
• BJS54 and XAS80, old geodetic datum used in China^[11]
• GCJ-02 and BD-09, Chinese encrypted geodetic datum.
• PZ-90.11, the current geodetic reference used by GLONASS^[12]
• GTRF, the geodetic reference used by Galileo^[13]
• CGCS2000, or CGS-2000, the geodetic reference used by BeiDou Navigation Satellite System^[13][14][15]
• International Terrestrial Reference Frames (ITRF88, 89, 90, 91, 92, 93, 94, 96, 97, 2000, 2005, 2008, 2014), different realizations of the ITRS.^[16][17]
• Hong Kong Principal Datum, a vertical datum used in Hong Kong.^[18][19]

The content is sourced from: https://handwiki.org/wiki/Geodetic_datum