1. Chemical Composition

2. Properties

The mechanical properties of 6061 depend greatly on the temper, or heat treatment, of the material.^[2] Young's Modulus is 69 GPa (10,000 ksi) regardless of temper.^[3]

2.1. 6061-O

Annealed 6061 (6061-O temper) has maximum ultimate tensile strength no more than 150 MPa (22 ksi),^[4][5] and maximum yield strength no more than 83 MPa (12 ksi)^[4] or 110 MPa (16 ksi).^[5] The material has elongation (stretch before ultimate failure) of 10–18%. To obtain the annealed condition, the alloy is typically heated at 415 °C for 2-3 hours.^[6]

2.2. 6061-T4

T4 temper 6061 has an ultimate tensile strength of at least 180 MPa (26 ksi)^[5] or 210 MPa (30 ksi)^[4] and yield strength of at least 110 MPa (16 ksi). It has elongation of 10-16%.

2.3. 6061-T6

 

6061-T6 Aluminum Standard Heat Treating Process. https://handwiki.org/wiki/index.php?curid=2068390

T6 temper 6061 has been treated to provide the maximum precipitation hardening (and therefore maximum yield strength) for a 6061 aluminum alloy. It has an ultimate tensile strength of at least 290 MPa (42 ksi) and yield strength of at least 240 MPa (35 ksi). More typical values are 310 MPa (45 ksi) and 270 MPa (39 ksi), respectively.^[7] This can exceed the yield strength of certain types of stainless steel.^[8] In thicknesses of 6.35 mm (0.250 in) or less, it has elongation of 8% or more; in thicker sections, it has elongation of 10%. T651 temper has similar mechanical properties. The typical value for thermal conductivity for 6061-T6 at 25 °C (77 °F) is around 152 W/m K. A material data sheet ^[9] defines the fatigue limit under cyclic load as 97 MPa (14 ksi) for 500,000,000 completely reversed cycles using a standard RR Moore test machine and specimen. Note that aluminum does not exhibit a well defined "knee" on its S-n graph, so there is some debate as to how many cycles equates to "infinite life". Also note the actual value of fatigue limit for an application can be dramatically affected by the conventional de-rating factors of loading, gradient, and surface finish.

3. Microstructure

Different aluminum heat treatments control the size and dispersion of Mg₂Si precipitates in the material. Grain boundary sizes also change, but do not have as important of an impact on strength as the precipitates. Grain sizes can change orders of magnitude based upon stress and can have grains as small as a few hundred nanometers, but are typically a few micrometers to hundreds of micrometers in diameter. Iron, manganese, and chromium secondary phases (Fe₂Si₂Al₉, (Fe, Mn, Cr)₃SiAl₁₂) often form as inclusions in the material.^[10]

Grain boundaries in extruded plate 6061 aluminum alloy. https://handwiki.org/wiki/index.php?curid=1774629

Grain sizes in aluminum alloys are heavily dependent upon the processing techniques and heat treatment. Different cross-sections of material which has been stressed can cause order of magnitude differences in grain size.^[11] Some specially processed aluminum alloys have grain diameters which are hundreds of nanometers,^[12] but most range from a few micrometers to hundreds of micrometers.^[13]

4. Uses

6061 is commonly used for the following:

• construction of aircraft structures, such as wings and fuselages, more commonly in homebuilt aircraft than commercial or military aircraft.^[14] 2024 alloy is somewhat stronger, but 6061 is more easily worked and remains resistant to corrosion even when the surface is abraded, which is not the case for 2024, which is usually used with a thin Alclad coating for corrosion resistance.^[15]
• yacht construction, including small utility boats.^[16]
• automotive parts, such as the chassis of the Audi A8 and the Plymouth Prowler.
• flashlights
• aluminum cans for the packaging of food and beverages.
• Scuba tanks and other high pressure gas storage cylinders (post 1995)

6061-T6 is used for:

• bicycle frames and components.
• many fly fishing reels.
• the Pioneer plaque
• the secondary chambers and baffle systems in firearm sound suppressors (primarily pistol suppressors for reduced weight and improved mechanical functionality), while the primary expansion chambers usually require 17-4PH or 303 stainless steel or titanium.^[17][18]
• The upper and lower receivers of many non mil-spec AR-15 rifle variants.
• Many aluminum docks and gangways, welded into place.
• Material used in some ultra-high vacuum (UHV) chambers
• Many parts for remote controlled model aircraft, notably helicopter rotor components.
• Large amateur radio antennas.
• Fire department rescue ladders

4.1. Welding

6061 is highly weldable, for example using tungsten inert gas welding (TIG) or metal inert gas welding (MIG). Typically, after welding, the properties near the weld are those of 6061-T4, a loss of strength of around 40%. The material can be re-heat-treated to restore near -T6 temper for the whole piece. After welding, the material can naturally age and restore some of its strength as well. Most strength is recovered in the first few days to a few weeks. Nevertheless, the Aluminum Design Manual (Aluminum Association) recommends the design strength of the material adjacent to the weld to be taken as 165 MPa/24000 PSI without proper heat treatment after the welding. Typical filler material is 4043 or 5356.

4.2. Extrusions

6061 is an alloy used in the production of extrusions—long constant–cross-section structural shapes produced by pushing metal through a shaped die.

4.3. Forgings

6061 is an alloy that is suitable for hot forging. The billet is heated through an induction furnace and forged using a closed die process. This particular alloy is suitable for open die forgings. Automotive parts, ATV parts, and industrial parts are just some of the uses as a forging. Aluminum 6061 can be forged into flat or round bars, rings, blocks, discs and blanks, hollows, and spindles. 6061 can be forged into special and custom shapes.^[19]

4.4. Castings

6061 is not an alloy that is traditionally cast due to its low silicon content affecting the fluidity in casting. It can be suitably cast using a specialized centrifugal casting method. Centrifugally cast 6061 is ideal for larger rings and sleeve applications that exceed limitations of most wrought offerings. ^[20]

5. Equivalent Materials

6061 Aluminum Equivalent Table^[21]

6. Standards

Different forms and tempers of 6061 aluminum alloy are discussed in the following standards:^[22]

• ASTM B209: Standard Specification for Aluminum and Aluminum-Alloy Sheet and Plate
• ASTM B210: Standard Specification for Aluminum and Aluminum-Alloy Drawn Seamless Tubes
• ASTM B211: Standard Specification for Aluminum and Aluminum-Alloy Bar, Rod, and Wire
• ASTM B221: Standard Specification for Aluminum and Aluminum-Alloy Extruded Bars, Rods, Wire, Profiles, and Tubes
• ASTM B308/308M: Standard Specification for Aluminum-Alloy 6061-T6 Standard Structural Profiles
• ASTM B483: Standard Specification for Aluminum and Aluminum-Alloy Drawn Tube and Pipe for General Purpose Applications
• ASTM B547: Standard Specification for Aluminum and Aluminum-Alloy Formed and Arc-Welded Round Tube
• ISO 6361: Wrought Aluminum and Aluminum Alloy Sheets, Strips and Plates

The content is sourced from: https://handwiki.org/wiki/Chemistry:6061_aluminium_alloy