The basic design philosophy of electrical machines has remained relatively unchanged for many years, as it has been constrained by the available manufacturing methods. With the rising demand for electric vehicles and green energy, there is a significant push towards higher efficiencies, power densities, lighter weights, and customized solutions for electrical machines, meaning that innovation in the field is required. One technology that might meet those demands is additive manufacturing (AM).
2. Additive Manufacturing
Current AM methods can be classified into seven main categories: vat photopolymerization, material extrusion, material jetting, binder jetting, powder bed fusion (PBF), direct energy deposition, and sheet lamination 
. Each method creates the three-dimensional object in a different way and has its own advantages and disadvantages. The biggest differences are in the available materials as photopolymerization and extrusion processes utilize mostly plastic materials, whereas metal objects are most often manufactured with PBF methods.
AM started off in 1987 with the emergence of stereolithography (SLA) 
, which is a vat polymerization technology. This method consists of solidifying thin layers of light-sensitive liquid polymers with a UV light source (Figure 1
a), which in the original case was a laser. The position of the laser beam can be accurately controlled using a mirror galvanometer system, resulting in extremely detailed parts. Modern consumer machines often use a UV LED array together with a high-resolution LCD photomask to reduce cost and complexity. This generally produces less detailed parts but has the benefit of being able to print the entire layer at the same time, which significantly improves the printing speed. While only the polymer can be directly hardened, other materials can be added into the liquid polymers as powders. After manufacturing, the hardened polymer can be burned away, leaving only the added material behind, although heavily shrunk compared to the original printed part. This allows SLA to be used for the manufacturing of ceramic and metal parts.
In 1991, fused deposition modeling (FDM) was commercialized with the launch of Stratasys’s first FDM printer 
. With this technology, individual layers are constructed by precisely extruding thermoplastic materials according to a CAD model (Figure 1
b). The low costs associated with FDM machines and materials have made it by far the most popular consumer AM technology 
. The material selection for FDM is wide, as many thermoplastics can be successfully printed, and similarly to SLA, other materials can be used as fillers. Furthermore, fully metal-based solutions based on material extrusion have recently become available 
The AM method with the widest material selection is binder jetting (BJ) 
, where an inkjet mechanism is used to selectively deposit a binder material into the powdered material to form layers. BJ can utilize many types of materials, such as ceramics, metals, and polymers. Full-colored prints are also possible due to the inkjet mechanism. The method allows for large build areas, as the binder solidifies at room temperature and does not introduce warping. Depending on the material, the printed parts need to be sintered or infiltrated with a low melting-temperature metal 
. This produces a part with significant internal porosity, potentially making the method unsuitable for applications where demanding material properties are required.
Schematics of (a
) SLA reprinted with permission from Ref. 
. Copyright 2016 Elsevier and (b
) FDM 
The first powder bed fusion (PBF) method called selective laser sintering (SLS) became available in 1992 
, although it was patented several years earlier 
. SLS involves using a powerful laser to selectively fuse powder particles into layers. After each layer, the build platform is lowered, a new coat of powder is applied, and the process repeats until the part is ready. The process of a general laser powder bed fusion (L-PBF) is illustrated in Figure 2
. The thickness of each coat of powder defines the layer thickness and determines the Z-axis accuracy of the part. The X- and Y-axis accuracy is determined by the laser assembly and material used. It can be used to manufacture parts from many different types of materials, even metals and ceramics, and can print without the use of support structures, as the part can be supported by the unsintered powder in the build chamber. The technology of selective laser melting (SLM), which was started in 1995 
, is similar to SLS, as it is also a powder bed process. However, instead of sintering, the (metal) powder is completely melted, leading to a less porous and more homogeneous part with improved thermal, electrical, and magnetic properties. A natural evolution of SLM is the technology of electron beam melting (EBM), where an electron beam is used instead of a laser. This allows for higher energy densities and a wider selection of materials. When printing metals, a dimensional tolerance of ±0.1 mm is often cited 
, and with SLM and EBM, densities over 99% can be achieved 
Schematic of a laser powder bed fusion process 
2.1. Materials Used in AM
AM allows many different materials to be used. In the context of thermal solutions for electrical machines, the relevant materials are either good electrical conductors, dielectrics, or have good magnetic properties. These materials are used for different purposes but for all of them, a high value of thermal conductivity is beneficial for increasing the total thermal performance of the machine.
The windings of an electrical machine need to be highly electrically conductive, meaning that copper is an ideal choice. AM allows the shape of the conductors to be optimized for both electrical and thermal purposes. However, a significant challenge in the additive manufacturing of machine windings is the relative difficulty of printing fully dense copper with a PBF based process, as copper reflects up to 98% of the energy applied by an infrared laser beam often used in SLM 
. This problem can be mitigated by using a green laser 
or an electron beam 
to achieve virtually fully dense parts with physical properties equivalent to the solid material. Copper can also be printed with other AM methods, such as BJ, SLA, and FDM, but due to the internal porosity of the final part, the thermal conductivity of the resulting object is lower 
Even though printing copper is less common due to the technological requirements, some impressive results have been achieved. Simpson et al. 
have used DMLS to create copper alloy windings that are shaped for minimal AC losses (Figure 3
a). The experimental results show reduced AC losses, although the electrical conductivity of the sintered material is only 51% IACS. A higher conductivity value of 90% IACS 
has been achieved by using SLM and a copper alloy (CuCr1Zr) to create an induction heater with integrated water cooling (Figure 3
b). The copper alloy CuCr1Zr is noteworthy, as it can be successfully manufactured using SLM with an infrared laser, while still having high thermal (310–340 W/m/K) and electrical (≥43 MS/m) conductivity 
. The primary alternative to copper is usually aluminum, with the alloy AlSi10Mg receiving the most attention in AM 
Additively manufactured (a
) copper alloy windings 
) an induction heater with integrated water cooling 
The printing of soft magnetic materials allows for the geometry of the core of an electrical machine to be optimized. This may include liquid cooling channels inside the iron core or cooling fins on the stator surface. The ability to integrate the cooling elements with the machine’s core can be beneficial due to the elimination of any contact thermal resistance, even if the thermal conductivity of soft magnetic materials is relatively low. The materials used are typically ferrosilicon alloys, which can be successfully printed using PBF and other AM methods.
The dielectric material needed to insulate the conductive windings is often a large source of thermal resistance in an electrical machine, as the electrically isolating materials used in machines are also poor thermal conductors (values of around 1 W/m/K). This is not the case with some ceramics, which through the use of AM could be utilized in electrical machines as thermally conductive isolation material. Several different AM methods can utilize ceramic materials, including SLA, by suspending the ceramic powder inside a liquid photopolymer 
. For example, Rauchenecker et al. 
were able to create complex-shaped alumina nitride ceramic parts with thermal conductivity values over 160 W/m/K. The thermal conductivities of some popular materials manufactured with different AM methods are presented in Table 1
Table 1. Thermal conductivities of popular materials used in AM.
||Effective Thermal Conductivity (W/m/K)
||26 (Fe-3.7 w.t.% Si) 
|Alumina nitride ceramic
2.2. Additively Manufactured Electrical Machines
In the realm of electrical machines, AM is still in the research stage. Individual components of an electrical machine have been successfully manufactured by several groups. Urbanek et al. 
have designed and manufactured a PMSM rotor from a soft-magnetic ferro-silicon alloy using a laser PBF process. The rotor is designed to utilize the advantages provided by AM by incorporating several design optimizations, including a skewed active part and a hollow shaft. Tseng et al. 
have used SLM to create a novel SRM rotor that incorporates skewing to reduce cogging torque and plastic ribs to reduce windage losses. Ibrahim et al. 
have used cold spray AM to create a rotor with alternative PM and soft magnetic composite material layers. The use of AM allowed them to eliminate the bridges and center-posts normally present in PMSM rotors, which limit the motor capabilities.
Some groups have used AM to produce working electrical machines, although not all parts were printed. Tiismus et al. 
have used SLM to create a working axial-flux switched reluctance motor (Figure 4
a). It includes a stator and a rotor which were manufactured from silicon steel. Wu et al. 
have designed and printed a fan motor that includes a rotor with an integrated impeller to achieve a robust motor with an improved power density (Figure 4
b). Ge et al. 
have used SLA and metal plating to create an electrostatic motor (Figure 4
Additively manufactured electrical machines: (a
) axial flux motor 
) integrated fan motor reprinted with permission from Ref. 
. Copyright 2021 Elsevier, (c
) electrostatic motor 
A completely additively manufactured electrical machine, where the windings, insulation, and soft magnetic materials are all printed concurrently, has not yet been achieved, as this would need advances in multi-material printing technologies. Powder bed fusion processes can generally only print a single material, although dual-metal systems do exist 
. Nonetheless, research in the area is going strong, as additively manufactured electrical machines can have many advantages over traditionally manufactured counterparts