Different physicochemical, sensorial, and nutritional attributes can be obtained using conventional emulsions. However, conventional emulsions do have limitations for some applications within the food industry. For instance, they are susceptible to breakdown through physical instability mechanisms, such as gravitational separation and droplet aggregation. Moreover, they have a limited ability to control the release profile of encapsulated ingredients. In addition, high fat contents are often needed to form oil-in-water emulsions with viscous or semi-solid textures, which is a drawback for creating reduced-calorie versions of some products. Recently, there has been growing interest in improving the healthiness, sustainability, and safety of foods in order to address some of the negative effects associated with the modern food supply, such as rising chronic diseases, environmental damage, and food safety concerns. In this context, there has been a trend toward the exploration of more advanced emulsion systems that have novel or improved functional attributes, such as reduced calories [3], controlled digestion behavior [4], and increased bioavailability of bioactives [5]. These advanced emulsions include a broad range of soft complex materials, including nanoemulsions, high internal phase emulsions (HIPEs), Pickering emulsions, multilayer emulsions, solid lipid nanoparticles, and multiple emulsions.

In this review article, we focus on the development and application of these advanced emulsion technologies. In particular, we focus on emulsions where the continuous phase is aqueous, since these are the most widely used in the food industry. The structures of these advanced emulsions are illustrated schematically in Figure 1. The key technical information from various literature reports is collected and tabulated, including the physicochemical principles underlying their formation, the choice of ingredients, the preparation conditions used, and their intended applications in foods. Special emphasis is given to the utilization of these advanced emulsions for the encapsulation, protection, and delivery of bioactive compounds. Finally, we discuss the challenges associated with the application of each of these advanced emulsions.

Nanoemulsions are similar to conventional emulsions except that they have droplet diameters that are smaller, ranging from around 20 to 200 nm. The small size of the droplets in nanoemulsions means that they have several potential advantages over conventional emulsions for specific applications, including better stability to gravitational separation and droplet aggregation, greater optical clarity, and higher bioavailability of encapsulated bioactive compounds. 

Pickering emulsions are similar to conventional emulsions but colloidal particles, rather than amphiphilic molecules, as used to form and stabilize them.  For instance, an O/W Pickering emulsion consists of oil droplets coated by a layer of colloidal particles, which is suspended in water.  The main advantage of Pickering emulsions is that they have a high resistance to coalescence because the colloidal particles generate strong steric and sometimes electrostatic repulsion between them.

Multilayer emulsions are similar to conventional emulsions but they contain multiple layers of materials adsorbed to the droplet surfaces, rather than a single layer of emulsifier.  The  composition, thickness, packing, and charge of the multilayers can be controlled by adding two or more different kinds of materials to the interfaces.  Typically, a charged emulsifier is used to form the first layer, and then oppositely charged biopolymers are added through a layer-by-layer electrostatic deposition method. The main advantages of multilayer emulsions are that they can be designed to have increased stability to heating, freezing, pH variations, high salt levels, chemical degradation, and gastrointestinal conditions.

Multiple emulsions, such as water-in-oil-in-water (W/O/W) emulsions consist of water droplets dispersed in oil droplets that are themselves dispersed in water droplets.  They are usually formed by homogenizing water and oil together with an oil-soluble emulsifier to form a W/O emulsion and then homogenizing this with water and a water-soluble emulsifier to form a W/O/W emulsion.  There are a number of potential advantages of these systems, including reduced fat, reduced bitterness, controlled release, triggered release, and protection from chemical degradation.

High Internal Phase Emulsions (HIPEs) are similar to conventional emulsions but they contain a very high  disperse phase content (typically > 73%), which means that the droplets are packed very close together and may become deformed.  These systems have semi-solid characteristics and therefore may be useful in applications where highly viscous, gelled or paste-like materials are required.

Solid lipid nanoparticles (SLNs) are similar to oil-in-water nanoemulsions, except that the lipid phase is crystalline.  They can be produced by making a nanoemulsion at high temperatures and then cooling it below the melting point of the fat.  The main advantage of SLNs is that they can protect encapsulated substances from chemical degradation and slow their release because the lipid phase is solidified, which reduces molecular diffusion.

3. Conclusions