2. General Methodology for Detection of Organic and Inorganic Components in Produced Waters
The stable isotopes of produced waters (δD
H2O and δ
18O
H2O) are mainly analyzed using the Dual Inlet-Isotope Ratio Mass Spectrometer (DI-IRMS) with an attached Multiprep bench for online analysis. δD values are assessed after online equilibration with Hokko beads using Multiprep. δ
18O compositions are also analyzed online using Multiprep after the waters had been equilibrated with carbon dioxide. Both isotopic compositions are reported relative to Vienna Standard Mean Ocean Water (VSMOW) with calibration by two-point normalization using United States Geological Survey (USGS) international standards USGS-45, USGS-46 [
13]. TOC is measured using a TOC-VCPH analyzer equipped with a catalytically aided 680 °C combustion chamber and normal sensitivity catalyst. Standardization is based on a 6-point calibration curve using a potassium phthalate standard. Extractable hydrocarbons in produced waters are usually detected using gas chromatography–mass spectrometry (GC–MS) in a full-scan mode or SIM (selected ion monitoring) mode (when specific compounds are in target). Organic compounds are identified after comparing mass spectral features with standard libraries of mass spectra, and standard compounds when available [
12]. The total dissolved solids (TDS) of completely dissolved solid particles in water are examined at the laboratory by filtering the water through a standard glass fibre. The filtrate is evaporated in a weighted dish and dried at 179–181 °C. The increase in weight of the dish is calculated as TDS in mg/L. The cations (Na
+, Mg
+2, K
+, and Ca
+2) in produced water samples are detected by atomic absorption spectrometry, whereas the anions (Cl
−, SO
4−2, HCO
3−, NO
3−, and F
−) are determined employing ion chromatography. Further, heavy metals are identified using inductively coupled plasma mass spectrometry (ICPMS) [
45].
3. Stable Isotopic Characteristics
The hydrogen and oxygen stable isotopes (δD
H2O and δ
18O
H2O) of formation water depict wide compositional variance but usually cluster to the right of the global meteoric water line (GMWL) (
Figure 1) [
2,
46]. However, water samples plotting to the GMWL’s left belong to highly coal bed methane-producing basins [
17,
47,
48,
49]. Open system carbon dioxide exsolution from CO
2-rich groundwater, low-temperature water–rock interactions, and methanogenesis may shift the meteoric water to the left of the GMWL [
2,
16,
18]. Meanwhile, mixing with basinal brines and/or seawater, high-temperature fluid–rock interactions, as well as evaporation may lead the meteoric water to the right side of the GMWL (
Figure 1) [
17,
19,
20]. Sometimes, methanogenesis may plot the meteoric water exactly above the GMWL [
12,
13] (
Figure 1). Further, clay and carbonate precipitation in coal cleats, as well as lithic and feldspar alterations in the interbedded sandstones, may yield groundwater enriched in deuterium and
16O [
17,
50]. This leads to high δD
H2O and low δ
18O
H2O values. In Antrim shales and some coal basins, augmented alkalinity with methanogenesis has precipitated isotopically heavier carbonates (high δ
13C) [
50,
51,
52,
53]. Carbon dioxide exsolution in an open system is confined within low permeability strata and recharged locally or from the basinal margin [
2].
Figure 1. The hydrogen and oxygen stable isotopes (δD
H2O and δ
18O
H2O) of formation water after Golding et al. [
2] and Ghosh et al. [
13]; Reuse of this figure from Golding et al. [
2] is permitted under Creative Commons CC BY-NC-SA 3.0 DEED License (
https://creativecommons.org/licenses/by-nc-sa/3.0 (accessed on 12 November 2023)) and reuse of this figure from Ghosh et al. [
13] is permitted by Elsevier and Copyright Clearance Center; license number: 5666531038082; dated 12 November 2023.
Further, in shale beds, the δD
H2O and δ
18O
H2O values plot on the GMWL or to the right of it, as observed in the Illinois, Michigan, and northern Appalachian basins [
54,
55,
56,
57]. The methane produced from the Illinois and Michigan basins has a microbial or mixed origin. The production water from these basins shows lower δD
H2O and δ
18O
H2O values than the modern meteoric water and perhaps suggests the dilution of basinal brines caused by Pleistocene glacial melt [
54,
57]. In addition, the molecular and gas isotopic signatures, along with the insignificant correlation between stable deuterium isotopes of formation water and methane (δD
H2O and δD
CH4, respectively), signify the thermogenic origin of methane from the northern Appalachian Basin. This basin’s water production is lower than the Illinois and Michigan basins. The δD
H2O and δ
18O
H2O parameters in this basin plot to the right of the GMWL and show a mixing signature with the modern meteoric water [
55].
4. Dissolved Inorganic Carbon (DIC) in Production Water
Groundwater comprises dissolved inorganic carbon (DIC). It results from the organic matter decomposition that yields δ
13C
DIC of <10‰, as well as from carbonate dissolution [
15,
58,
59,
60,
61]. Methanogenesis in coal and shale beds produces isotopically lighter methane (δ
13C
CH4 ~<55‰) and the residual carbon dioxide is enriched with the heavier carbon (
13C) due to the microbial degradation of substrates. This leads to the positive δ
13C
DIC in formation water [
54,
56,
57,
60,
61,
62,
63]. Production waters related to microbial or mixed origin of gas in coal and shale beds exhibit an incremental trend of the δ
13C
DIC with rising alkalinity [
47,
54,
56,
57]. However, this relation becomes weak if the gas is thermogenic in origin [
55]. The microbial gas from the Illinois Basin reveals higher δ
13C
CH4, δ
13C
CO2, and δ
13C
DIC values [
56]. The thermodynamics of the system, along with the groundwater residence time, governs the degree of isotopic fractionation.
Quillinan and Frost [
22] investigated the isotopic signatures of oxygen, hydrogen, and DIC in produced water samples from 197 coal bed gas wells at the Powder River Basin in Wyoming and Montana. Their investigation revealed that the isotopic compositions vary due to biological and geochemical mechanisms occurring along the groundwater flow channels, variations in the design of the well completion design, the dewatering of coal beds, the partial hydraulic seclusion of coal seams from adjacent litho-units, and the consequent mixing of groundwater. The δD
H2O and δ
13C
DIC fluctuate along the flow path across the basin, suggesting variations in isotopic fractionations associated with different methanogenesis routes. Further, δD
H2O and δ
13C
DIC of every coal bed are distinctive in areas with multiple coal beds. The Powder River Basin coal bed-produced waters comprise δ
18O
H2O ranging from −26.3‰ to −16.9‰. Carter [
64] reported that the δD
H2O and δ
18O
H2O values of the production water are lower than the surface waters, suggesting a recharging of the coal bed gas waters in colder climatic conditions compared with the present day. The δ
18O
H2O and δD
H2O are depleted in waters produced from the stratigraphically lowest coal seams northeast of the Powder River Basin, indicating groundwater recharge under variable meteoric conditions [
65]. Additionally, coal bed waters collected from single-completion wells exhibit higher δ
13C
DIC (+10‰ to +25‰). In shallow wells and fields that comprise multiple coal seams or have open-hole completions extending beyond a single coal seam, the produced waters reveal variable and even negative δ
13C
DIC values. The oxidation of methane that has led to the positive excursion of δ
13C
CH4 and δD
CH4 possibly results in the enrichment of lighter carbon isotopes in the DIC [
59]. In open-hole completions, due to a dearth of cement, waters from isotopically depleted non-coal bearing litho-units infiltrate the production well and mix with the coal bed formation water. This mixing may have lowered the δ
13C
DIC values of the production water [
65]. The δ
13C
DIC parameter is also depleted along groundwater flow paths in deeper coal seams. Methanogenesis, hyperfiltration, and the mixing of groundwater may affect the isotopic fractionation along the groundwater flow paths [
59,
66,
67]. Rising δD
H2O with decreasing δ
13C
DIC along groundwater flow paths may often imply that hydraulic confinement failed within the reservoir [
68]. Hyperfiltration may influence isotopic fractionation in low permeability strata [
69,
70]. Owing to advection, groundwater flowing through a fine-grained matrix along a steep gradient acts as a filtration membrane and impedes larger molecules [
59]. The pathways of methanogenesis also influence the δ
13C
DIC values in co-produced waters. Flores et al. [
71] revealed an increase in the δ
13C
DIC with the methane generation from both hydrogenotrophic and acetate formation routes near the basinal margins. However, the hydrogenotrophic pathway dominates in deeper coal seams. Near the outcrop, the hydrogenotrophic pathway utilizes the δ
13C
DIC (−12 to −7‰) of the meteoric water that recharges the coal seam.
With the progressive consumption of lighter carbon, the δ
13C
DIC becomes heavier, and consequently, the methanogens are compelled to fractionate isotopically heavier carbon dioxide. The fractionation of such isotopically heavier CO
2 results in the positive excursion of the δ
13C
CH4 and consequently more isotopically depleted δ
13C
DIC. Hence, hydrogenotrophic methanogenesis may lead to the gradual depletion of the δ
13C
DIC of the co-produced waters [
65]. Alternately, the extent of microbial methane generation is often indicated by positive δ
13C
DIC values, as a small amount of methanogenesis can enrich a small DIC pool. However, the δD
H2O is not enriched readily. A considerable positive excursion of the δD
H2O needs a vast methane yield [
59]. Therefore, production waters enriched in both δ
13C
DIC and δD
H2O values possibly advocate a vast amount of methanogenesis [
69].
5. Chemical Composition of Co-Produced Waters of CBM and Shale Gas Exploration
Production water related to coal bed methane and shale gas systems comprises a myriad of organic and inorganic constituents. The physicochemical characteristics of co-produced water depend on the geochemical paradigms of gas-bearing strata, their age and depth, latitude, the compositions of the generated hydrocarbons, and the synthetic chemicals added during their production. Several naturally occurring moieties are dissolved in coal and shale bed water, and many compounds are dispersed from adjacent litho-units. The groundwater residence time also affects the concentrations of these compounds in coal and shale bed waters. Such compounds include organic functionalities, polycyclic aromatic hydrocarbons (PAHs), aromatic amines, alkyl phenols, long-chained fatty acids, alkyl biphenyls, alkyl benzenes, aliphatic hydrocarbons, radioisotopes (
238U,
235U,
232Th,
226R,
228Ra,
222Rn, and
40K), metals (As, B, Ba, Cd, Co, Cr, Fe, Hg, Ni, V, Zn), salts, and other inorganics [
11,
72]. Individual organic components in production water related to coal bed methane fields range from 1 to 100 μg/L. However, the total PAHs span from 50 to 100 μg/L, while the total organic carbon (TOC) varies from 1 to 4 mg/L. Production water from shale beds exhibits similar ranges of organic functionalities, while the TOC ranges up to 8 mg/L. However, hydraulic fracturing may significantly alter these components’ concentrations by adding synthetic chemicals. As an example, hydraulic fracturing in the Marcellus Shale has augmented the TOC level up to 5500 mg/L and introduced large abundances (1000 s of μg/L) of biocides, scale inhibitors, solvents, and other synthetic organic chemicals [
11].
5.1. Inorganic Ions, Salts, and Total Dissolved Solids
The salinity of the production water varies from a few parts per thousand (ppt ‰) to around 300 ppt (salinity of saturated brine). It is more saline than seawater (32–36 ppt) [
73]. This high salinity makes the produced water denser than the seawater [
74]. Further, the water produced in Hibernia shows a salinity range from 46–195 ppt. Sodium and chloride are the major cations and anions found in produced water. The relative abundance of inorganic ions decreases from Na
+, Cl
−, Ca
+2, Mg
+2, K
+, SO
4−2, Br
−, HCO
3−, and I
−. Variations in the relative abundance of these ions contribute to the toxicity of produced water [
75]. Methanogenesis, the oxidation of pyrite, the reduction of sulfate, and the dissolution of salts lead to the bicarbonate and sodium enrichment in the coal bed formation water. Sodium is formed from cationic exchange, weathering of clay, and soluble salts in soil [
76]. Surfacing the coal bed formation water brings about further geochemical transformations, which include calcite and iron hydroxide precipitation. In semi-arid hydrocarbon basins, soluble salts deposit naturally in soil. Introducing coal bed formation water may mobilize these salts and enhance groundwater salinity at shallower depths [
76]. Produced water from sour oil and gas fields comprises large amounts of sulfides and elemental sulfur. High barium and other cations may often form insoluble sulfides and sulfates in produced water. Offshore-produced water from Brazil often consists of greater than 2000 mg/L sulfate, while produced water recovered in the year 2000 from the Grand Banks off Newfoundland, Canada, comprised 248–339 mg/L of sulfate. Stimulatory and/or inhibitory responses from biota residing in coal and shale beds may elevate the ammonium ion concentrations in produced waters [
77].
Meanwhile, phosphate and nitrate concentrations are low in produced water. The Hibernia produced water comprises 0.02 mg/L nitrate, 0.35 mg/L phosphate, and 11 mg/L ammonia. Ammonia concentrations in produced water from Brazil range from 22 to 800 mg/L [
72]. The total dissolved solids (TDS) in produced water have variable abundances: low in the Powder River Basin and high in Uinta (UT) and parts of the Black Warrior (AL) basins [
26,
27,
28,
78]. Further, produced waters from many shale gas fields are hypersaline. Produced waters from the Marcellus Shale (USA) comprise TDS up to 200,000 mg/L [
24,
29]. Flowback water recovered from wells during the first 10–20 days contains low TDS as fresh fracturing fluid may dilute the formation water until and unless saline water is injected as the fracturing fluid [
29].
5.2. Total Organic Carbon and Volatile Fatty Acids
Total organic carbon (TOC) in produced water varies from 0.1 to >11,000 mg/L [
36]. Produced water from Louisiana comprises around 5–127 mg/L particulate TOC and 67–620 mg/L dissolved TOC [
79], while Hibernia-produced water consists of 300 mg/L TOC. Means et al. [
80] advised that a substantial fraction of dissolved organic carbon may be present in colloidal suspension. Moreover, Orem et al. [
12] suggested that the mean TOC value in the produced water from CBM wells ranges from 1.18 to 4.5 mg/L. This may indicate a minimal influence of organic moieties yielded during hydraulic fracturing, hydrocarbon production, and other operating activities. Produced water from the Black Warrior Basin consists of 61.4 mg/L TOC due to the presence of oils during gas production. Meanwhile, produced water from shale gas fields comprises higher TOC than from the CBM fields, ranging from 1.2 to 5804 mg/L. The average TOC values in the produced waters from Antrim Shale and Marcellus Shale are around 8.12 mg/L and 346 mg/L, respectively. These higher TOC values in shale gas fields than in the CBM fields may indicate the occurrence of miscible oil associated with shale gas, the addition of synthetic organic compounds during hydraulic fracturing, and other site-specific production techniques associated with shale gas production [
11]. However, hydraulic fracturing is also applied in CBM fields. Differences in geological conditions, the permeability of coal and shale beds, the thermal maturity of kerogen, etc., may influence the use and abundance of chemicals during hydraulic fracturing, which may affect the TOC of produced or flowback water.
Produced water from CBM and shale gas fields comprises volatile fatty acids (VFS) like acetate. Other VFAs are also present but often remain below the detection limit of instruments. Acetate may range from <0.1 mg/L to 53.7 mg/L, while the mean value varies from 0.3 to 10.6 mg/L [
11]. The produced water of some gas and oil fields contains up to 5000 mg/L of acetate or aliphatic acid anions due to the thermogenic cracking of kerogen at the ‘Oil window’ and ‘Gas window’ (80–200 °C). Aliphatic acid abundances show low concentrations below 80 °C as these are used by sulfate-reducing bacteria and methanogenic archaea as substrates [
81]. Additionally, apart from temperature, concentrations of VFAs may also depend on the time during which the hydrocarbon source rocks were exposed to geothermal gradient and the thermal cracking of kerogen took place.
5.3. Acids
Apart from TDS, TOC, and VFAs, produced water contains aliphatic and aromatic carboxylic acids. TOC in produced water samples comprises a mixture of lighter carboxylic acids, i.e., propanoic, acetic, pentanoic, butanoic, hexanoic, and formic acids [
82,
83,
84,
85]. Formic and/or acetic acids dominate in the produced water, and their abundance decreases with the rising molecular weight [
86,
87]. In produced water samples from the North Sea, Strømgren et al. [
86] observed a total of 43–817 mg/L C
1 to C
5 organic acids, while the concentrations declined with increasing molecular weight (total 0.04–0.5 mg/L C
8 to C
17 organic acids). Moreover, many produced waters from California, the US Gulf of Mexico, and the North Sea comprise 60–7100 mg/L light aliphatic organic acids [
84,
87,
88,
89]. Produced water from Louisiana comprises small abundances of both aliphatic and aromatic acids, while aliphatic acids dominate over methylbenzoic and benzoic acids [
90]. Plants, microbes, and fungi synthesize and degrade these light organic acids and provide nutrients for the growth of phytoplankton and zooplankton. The microbial decomposition of hydrocarbons and hydrous pyrolysis may yield organic acids in hydrocarbon-containing formation [
91,
92,
93]. Large abundances of naphthenic acids are found in formations comprising bio-degraded crude oils [
91,
94]. Due to its partial solubility, naphthenic acids, if abundant in crude oils, are also present in co-produced waters. Bitumens, produced water, and heavy crudes from Alberta oil sands comprise large abundances of many naphthenic acids with 8–30 carbon atoms, while produced waters from Suncor and Syncrude consist of 24–68 mg/L naphthenic acids [
95]. The Troll C platform on the Norwegian continental shelf produces water that contains variable compositions and concentrations of naphthenic acids, suggesting variable extents of the microbial degradation of crude oils in different sectors of the reservoir [
91]. The naphthenic acid found in these crude water samples is represented by salicylic acid, methylated benzoic acid series, naphthoic acids, and their several analogous. Anaerobic microbes, usually in hydrocarbon-bearing formations below 100 °C, may degrade crude oil to produce these organic acids [
11]. These acids corrode production pipes, add to aqueous toxicity, and create environmental hazards [
96].
5.4. Hydrocarbons
Produced water comprises saturated and aromatic petroleum hydrocarbons. Their solubility in water declines with rising molecular weight. Aromatic hydrocarbons are more hydrophilic than saturated ones of similar molecular weights. These hydrocarbons are present in dispersed and dissolved forms in produced water. Dispersed hydrocarbons, such as oil droplets, can be easily removed from the produced water. However, phenols, organic acids, metals, and dissolved hydrocarbons are tenacious. Meanwhile, not all the oil droplets can be removed [
97], and such droplets comprise less soluble high-molecular-weight saturated and aromatic hydrocarbons [
98].
Monoaromatic hydrocarbons, such as benzene, toluene, ethylbenzene, and xylene (BTEX), and low molecular weight saturated compounds are abundant in produced water [
72]. BTEX may range up to 600 mg/L in untreated production water. Small amounts of trimethyl and tetramethyl benzene are also present in produced water. The benzene concentration declines with alkylation [
99]. Due to high volatility, BTEX escapes drastically during the treatment of produced water by air stripping and mixing seawater with produced water [
100]. Saturated hydrocarbons are present in low concentrations in produced waters. The short-chain alkanes are more abundant than the longer-chain homologs [
101].
Extractable hydrocarbons in produced waters include heterocyclic compounds, alkylated benzenes, biphenyls, long-chain fatty acids, phenols, alkanes up to C
25, along with polycyclic aromatic hydrocarbons [
25]. Polycyclic aromatic hydrocarbons (PAHs) are the most common organic constituents in produced water and are also of great environmental concern due to their toxicity. PAHs consist of two or more benzene rings fused linearly or in an angular or clustered organization [
102,
103,
104,
105,
106,
107,
108,
109]. PAH concentrations in produced waters vary from 0.040 to 3 mg/L and comprise mainly hydrophilic bi- or tri-aromatic PAHs, like alkylated phenanthrenes and naphthalenes. PAHs that have four–six rings are merely detected in treated produced water due to their low solubility in water [
72]. Orem et al. [
26] observed that total PAHs in the produced water from the Powder River Basin range up to 23 μg/L, while the abundance of individual moieties varies from <0.1 μg/L to 18 μg/L. Alkylated phenanthrenes, anthracenes, and naphthalenes are the major PAHS, while indene, fluorene, and pyrenes are also present. Substituted biphenyls and alkyl benzenes are also found in low concentrations (<1 μg/L). Heterocyclic compounds include benzothiols and their derivatives. Nonylphenols in the produced waters span from 0.1 to 7.9 μg/L. Octylphenols and nonylphenols are commonly applied as surfactants during CBM production. However, they may also originate from coal [
11]. Apart from long-chain alkanes, saturated compounds contain terpenoids and long-chain fatty acids. In the Powder River Basin, the aromatic compounds dominated over the saturated compounds in the produced waters.
Formation water samples from the USGS CBM research wells from the northern part of the Powder River Basin depict comparable organic distributions. The produced water samples comprise alkyl phenols, alkyl benzenes, heterocyclic compounds, long-chain alkanes, long-chain fatty acids, and PAHs [
11]. The most abundant compounds are the long-chain fatty acids. Mainly, two-ring PAHs and methylated two-ring compounds are observed in low concentrations. Further, produced water samples from the Black Warrior Basin, Alabama, comprise alkyl phenols (<0.1 to >15 μg/L), heterocyclic functionalities (<0.1 to >3 μg/L), long-chain fatty acids (0.6 to >8 μg/L), and PAHs (<0.1 to >15 μg/L). Total concentrations of PAHs range up to 50 μg/L in these samples, which are more than double the PAH abundance in the Powder River Basin-produced water samples [
11]. A higher thermal maturity in the Black Warrior coals (high- to low-volatile bituminous) with a more condensed aromatic structure would have influenced the PAH distributions in the co-produced water. Heterocycles, like benzothiophenes, quinolones, and benzothiazoles, and aromatics, such as acetophenone, alkyl benzenes, and phenyl phosphates, are also observed in these produced waters. Moreover, long-chain alkanes, long-chain fatty acids, alkyl phenols, heterocyclic compounds, and PAHs are also observed in the water produced in the Williston and Illinois basin CBM fields. Lower abundances of PAHS, like two-ring and methylated two-ring compounds, are found in these samples. Long-chain alkanes and fatty acids are the most dominant compounds in these water samples. The long-chain alkanes are either indigenous to coals and/or would have originated from synthetic chemicals, corrosion inhibitors, and diesel fuel used during CBM production [
11]. Produced water from the Harriet A platform located at the Northwest Shelf of Australia consists of 5–10% PAHs in the dissolved fraction, which dominantly comprises alkylnaphthalenes and traces of alkylphenanthrenes [
110]. The particulate fraction in the produced water contains high abundances of phenanthrenes, naphthalenes, pyrenes/fluoranthenes, chrysenes, and dibenzothiophenes.
Additionally, shale gas-related produced waters may often show dissimilarities in organic distributions from the CBM-related produced waters. Production water from the New Albany shale comprises substituted phenols, long-chain fatty acids, and PAHs. PAHs are represented by naphthalene, phenanthrene, anthracene, acenaphthene, and chrysene and their alkylated homologs and pyrene. Benzothiazole is the most prominent heterocyclic compound present in these water samples. Octa-atomic sulfur is also present in the produced waters. Most of the samples contain long-chain alkanes, either indigenous to shale or derived from synthetic hydrocarbons used during shale gas production. These compounds range from <0.1 to 25 μg/L [
11]. Production water from the Marcellus Shale comprises C
11 to C
32 strait-chain and branched alkanes, alkenes, and long-chain fatty acids. These fatty acids are the biodegradation products of shale geopolymers [
111]. Heterocycles such as hexahydro-1,3,5-trimethyl-1,3,5-triazine-2-thione (a synthetic chemical applied as a biocide) are present. Ethylene glycol and its derivatives, like triethylene glycol monodocecyl ether, diethylene glycol monododecyl ether, etc., are also found in these water samples, introduced during hydraulic fracturing. Such compounds are used as anti-freezing agents to inhibit scaling and decrease friction in production pipes during hydraulic fracturing. 2,2,4-trimethyl-1,3-pentanediol, an industrial solvent, and Tetramethylbutanedinitrile from PVC can also be found in the produced water samples. Abundances of individual moieties span from <1 to >5000 μg/L due to the introduction of hydraulic fracturing components to the produced water [
11].
5.5. Phenols
Produced waters usually comprise <20 mg/L phenols [
72]. The produced water from the Norwegian sector of the North Sea and Louisiana Gulf coast comprises 0.36–16.8 mg/L and 4.5 mg/L phenols, respectively [
14,
101]. Phenols, di-, and tri-methylphenols represent these phenols. The concentrations of methylated phenols logarithmically alleviate with the increment in alkyl carbons [
112]. Six produced waters from the Norwegian sector comprise 4-
n-nonylphenol (0.001–0.012 mg/L), the most toxic alkylphenol. As discussed above, alkylphenol ethoxylate (APE) surfactants comprising nonylphenols and octylphenols are often applied for CBM production to enhance the pumping of waxy crude oils. Some alkylphenols dissolve in produced water if the surfactant decays [
72]. Owing to their toxicity, the APE surfactants have been replaced during hydrocarbon production [
113].
5.6. Radiogenic Isotopes
Radium-226 (
226Ra) and radium-228 (
228Ra) are the most abundant radiogenic isotopes found in the produced waters. The radioactive decay of thorium-232 (
232Th) and uranium-238 (
238U) present in minerals of the hydrocarbon plays may yield radium [
114,
115]. Radionuclide concentrations in produced water are calculated as the radioactive decay rate and are presented in picocuries/L (pCi/L) or becquerels/L (Bq/L). Therefore, a pCi value of 1 indicates 1 picogram of
226Ra or 0.037 picogram of
228Ra [
99]. Oceanic surface waters’
228Ra and
226Ra activities range from 0.005 to 0.012 pCi/L and 0.027 to 0.04 pCi/L, respectively [
116,
117]. Produced waters from several hydrocarbon fields comprise substantially higher radium activities [
118] than observed in oceanic surface water. Along the US Gulf Coast of Mexico, the total abundance of
228Ra and
226Ra activities in produced water samples from hydrocarbon and geothermal wells vary from less than 0.2 pCi/L to 13,808 pCi/L [
86,
114,
119]. Meanwhile, the
228Ra and
226Ra activities show a good correlation in the produced water samples from the Norwegian continental shelf due to little radium activity [
72]. Offshore produced waters, except those from the Gulf Coast of Mexico, exhibit low average
228Ra and
226Ra activities (<200 pCi/L). However, several North Sea production sites contain produced water that shows high
226Ra activity. Discharged water to Atlantic Canada reveals low radium activity, yet it is higher than the radium activity in seawater. Furthermore, other radioisotopes are also present in produced water with low average activity. The
210Pb, daughter isotope of
226Ra, often shows higher activity than the
228Ra and
226Ra. Four Louisiana platforms comprise production waters with an average of 5.60 ± 5.50 pCi/L to 12.50 ± 2.60 pCi/L activity of
210Pb [
120].
210Po, a daughter of
226Ra, is also found in North Sea production water with low mean radioactivity. The parent radioisotopes, i.e., the
232Th and
238U, show little activity in produced water.
5.7. Metallic Substances
Various metals occur in microparticulate or dissolved forms in produced water. Concentrations, chemical species, and types of metals depend on the geology and age of the hydrocarbon-bearing formations [
74]. Additionally, metal composition and the abundance of water injected during hydraulic fracturing may alter the metal composition and concentrations in the produced water. Some metals of different origins in produced water depict significantly larger concentrations than in seawater, such as manganese, iron, zinc, mercury, and barium [
121]. Produced water from Hibernia comprises particulate and dissolved manganese, iron, and barium, concentrations of which are higher than in normal seawater. Due to its anoxic redox condition, large concentrations of manganese and iron may occur in the solution of the produced water. When brought to the surface, such formation waters precipitate manganese and iron oxyhydroxides upon atmospheric exposure. Many metals also co-precipitate with manganese and iron upon atmospheric exposure. Lead and zinc may derive partially from galvanized steel bodies in contact with produced water [
72].
5.8. Production-Related Chemical Substances
Hydraulic fracturing and horizontal drilling are the principal procedures for CBM and shale gas exploration. The persistent exposure of shale formation to oil-based drilling fluid may reduce the mechanical strength and friction coefficient of the shale surface. These may lead to unstable plugging zones with reduced pressure-bearing capacity [
7]. CBM and shale gas production systems use numerous synthetic chemicals and additives in drilling fluids. These chemicals help in the hydraulic fracturing, pumping, and recovery of hydrocarbons, protect from corrosion, isolate water, oil and gas, and hinder the formation of methane hydrates in hydrocarbon production units [
72]. These substances include cross-linkers (ethylene glycol), foaming agents (ethanol), delivery gels (diesel fuel, guar gum), corrosion preventers (methanol), biocides (brominated nitrilopropionamides), and several other compounds [
33,
122]. Several chemicals show greater solubility in oil than in production water, enriching such synthetic chemicals in produced crude oil. The water-soluble chemicals are disposed of with the produced water, eventually harming the environment.
Meanwhile, after treatment, the abundance of several additives decreases. Scale and corrosion preventers and chemicals, used to treat gas, may remain high in the production system. Chemicals used for treatment are injected to mitigate specific complications. If such chemicals are used substantially or in excess amounts, they adversely influence the environment. Such environmental concerns caused by synthetic treatment chemicals are often reduced by the applications of advanced management procedures like the DREAM model to assess environmental impact factors (EIF) for individual chemicals, regulatory compliance effluent toxicity testing processes, or offshore chemical selection systems [
72].