In response to the environmental pollution caused by conventional energy sources, researchers worldwide have searched for reliable and sustainable energy production sources. In this line, bioelectrochemical systems (BESs) capable of transforming chemical energy into electrical energy aided by microorganisms as catalysts have been developed [1]. BESs are promising technologies that have been implemented to replace energy sources from fossil fuels, such as petroleum, natural gas, and coal [1,2], in response to worldwide high energy demands. BESs can be classified into (i) microbial desalination cells (MDCs) [3,4,5], (ii) microbial electrosynthesis cells (MECs) [6], (iii) enzymatic biofuel cells (EBCs) [7], (iv) electrolysis cells (ECs) [8], (v) microbial solar cells (MSCs) [9], (vi) biobatteries [10,11], (vii) constructed wetland microbial fuel cells (CW-MFCs) [12], and (viii) microbial fuel cells (MFCs). To date, considering the types of BESs, MFCs are the oldest, being the first BES presented in 1911 [13]. The operation of an MFC is based on bacterial activity, where so-called electrochemically active bacteria (EAB) break down (i.e., oxidize) organic matter (OM) to produce bioelectricity [14]. During this process, the EAB use their metabolic pathway to transport electrons [15,16].

The components of an MFC basically include an anode compartment and a cathode compartment (Figure 1a), both separated internally by a membrane. The anode chamber is mainly responsible for the oxidation of OM (Equation (1)) in the substrate (e.g., in presence of water) through microbial activity, producing electrons (e⁻), protons (H⁺), and carbon dioxide (CO₂) [17]; then, e⁻ are transported toward the cathode chamber [14,18]. Subsequently, the protons are associated with oxygen, thanks to the PEM (Equation (2)), in order to form an essential compound in the reaction: the water molecule (H₂O). Equation (3) indicates the complete chemical reaction in an MFC. Additionally, the electron transfer mechanism at the anode surface of an MFC is presented in Figure 1b. The author referred to the following critical reviews to better understand this area [16,19].

Since the implementation of MFCs, wastewater has been used as an excellent organic substrate for these systems, improving their efficiency in both bioenergy generation and waste management [20,21,22,23,24,25]. The highest power density of 4.99 ± 0.02 W/m² was reached in a dual-chamber MFC inoculated with an excellent mixed culture [26]. This high performance was obtained in a three-dimensional N-doped bio-anode MFC fabricated with carbon felt as the anode and cathode and was higher than that of previous studies using carbon-based materials. The MFC reactor had a working volume of 80 mL in each chamber. The system’s high performance was likely due to the electrode materials used. More recently, a high power density of 1793 ± 77 mW/m² was achieved in an MFC operated with atomically dispersed Fe–N₄ moieties as an excellent cathode catalyst [27]. The atomically dispersed Fe–N₄ moieties were considered a perfect option to enhance the performance of the MFCs.

MFC technologies have received significant attention, due to their extraordinary capacity to produce bioenergy without harming the environment. Figure 2 illustrates the advances that have been made to bring MFC technology into the realm of practical application. To date, more than 7363 investigations have been conducted on the use of MFCs for low-cost electricity generation. In addition, over 3216 review papers have been published on different aspects of MFCs, followed by 2530 book chapters, 388 conference abstracts, and 284 encyclopedias. It is worth mentioning that these data were obtained only from the ScienceDirect database, as there were more publications on energy recovery using MFC systems than on other platforms.

Great strides have been made in improving bioelectricity production by MFCs. Many recent studies have reported high power generation efficiency using MFCs inoculated with different types of waste (e.g., wastewater, sludge, and human urine). 

The highest power density of 2203 mW/m² was obtained using an SC-MFC inoculated with anaerobic sludge as an outstanding inoculum [115]. The SC-MFC was constructed with a graphite brush as an anode, while modified materials—that is, graphite-based nanomaterials and platinum/carbon (Pt/C)—were utilized for the cathode. The performance achieved in the study was referred to as the cathode modification and the operating conditions of the MFC (i.e., 30 days of operation and 27 cycles). In contrast, Subran et al. [116] obtained a highest power density of 590 mW/m² (with 78% COD removal efficiency) in an SC-MFC using carbon cloth as an anode and cathode, separated by a Nafion 117 membrane. This value was almost four times lower than that reported with Pt/C [115]. In the study by Sathish et al., rGOHI-AcOH (acetic acid) and rGO/Ni (reduced graphite oxide nickel nanoparticle composite)—two reduced graphene oxide hydrogen iodides—were used with Pt/C as catalysts [115]. The results were interesting, as they indicated that the rGOHI-AcOH-based catalysts, as mentioned earlier, could feasibly drive the MFC system without interruption (in terms of power density). The power output found in [116] was 76.6% higher than the maximum power output (138 mW/m²) reported in a tubular MFC (T-MFC) [117]. The T-MFC was fabricated using a graphite rod as an anode electrode, carbon cloth-coated Pt (200 cm²) as a cathode electrode, and nanocomposite as a proton exchange membrane. The findings indicated that the best option for improving the performance of an MFC is modifying its electrode (i.e., synthesized and characterized nanocomposite membranes) and using suitable configuration materials. In the previous study by Bensaida et al. [118], the highest power density of 833.33 mW/m² was obtained in a prototype MFC inoculated with Mg(OH)₂-coated iron nanoparticles. This value was 29.19 and 83.34% superior to that in agro-waste and synthetic wastewater, respectively; however, it was approximately three times inferior to that reported in anaerobic sludge elsewhere [115].

Anaerobic sludge appears to be the most suitable inoculum for use in MFCs to improve the power density efficiency, compared to others. This kind of inoculum (sludge) has tremendous potential to increase the performance of MFC systems [115]. This performance enhancement was due to the proper characteristics related to the sludge used, including operating conditions and modification of the reactor. It is crucial to note that the efficiency of an MFC also depends on factors such as the type of electron acceptors and catalysts used. Both electroactive biofilms and extracellular electron transport in MFCs are highly dependent on the physicochemical properties of the operational anode surface; therefore, surface modification of conventional anode materials is critical for improving the performance of MFCs. However, more studies on the use of substrate and electrode modifications are required in order to reliably increase energy production in MFC technologies.

On the other hand, in their quest to increase the amount of OM and keep bacterial populations active on the anode surface, researchers have investigated other types of substrates with great potential, such as acetate, butyrate, glucose, cellulose, and sucrose. These substrates have all been used in MFCs in an attempt to improve their output power, as described in [2]. The main idea of using such substrates in MFCs is to improve the transport of protons from one compartment to another, in addition to forming good biofilms on the electrode and keeping the bacterial community active. The highest power densities in the range of 305 and 506 mW/m² have been recorded in an SC-MFC inoculated with butyrate (1000 mg/L) and acetate (800 mg/L), respectively [119]. It was noted that the SC-MFC using acetate presented better performance, in comparison to that inoculated with butyrate. The difference between the reactors regarding the power density arose from the concentrations of the substrates. Later, in an SC-MFC inoculated with glucose, the highest power density of 52 mW/m² was reported, approximately 9 times and 5 times less than those derived for butyrate and acetate, respectively [120]. Hashmi et al. [121] have recently reported the highest power density of 71.12 mW/m² in a DC-MFC when removing hazardous materials from wastewater. This yield in MFC was due to the addition of 350 μmol/L of C₆N₆FeK₃ (potassium ferricyanide) in the cathode compartment. Concurrently, 180 μmol/L of CH₂ (methylene) was applied to the anode compartment. As mentioned above, a high concentration of the chemical compounds is an excellent option to increase the performance of MFCs while treating wastewater.

According to the above studies, modifying the electrode material is the better or cheaper option to improve MFC performance, in terms of power density, compared to conventional electrodes. The configuration of an MFC using a conventional electrode is expensive, making its large-scale application much more costly. Furthermore, another alternative to improve the performance of MFCs is the use of organic substrates, which are excellent electron donors. Finally, anaerobic sludge has been reported to be one of the best inoculums (due to characteristics such as bacterial diversity, as described earlier) for improving power generation in MFCs, followed by Mg(OH)₂-coated iron nanoparticles, rGOHI-AcOH, and acetate as excellent substrates (with excellent carbon sources to improve or stimulate EAB) for MFC technologies [115,119]. Furthermore, algae have been reported to be a good substrate for enhancing the performance of MFCs for the recovery of value-added products from wastewater [122,123], including biofuels [124], bioremediation, and bioelectricity generation [125,126]. According to the literature, MFC-based algae have great potential for improving power efficiency, nutrient removal, heavy metal recovery, and bioremediation of contaminants.

Yaqoob et al. [127] recorded the highest current density of 36.84 mA/m² (within 20 days of operation) using potato wastewater as an electron donor for the biodegradation of pollutants in a benthic microbial fuel cell (BMFC). This MFC performance was 82.28% less than that previously reported in a DC-MFC operated with potato waste as the substrate [128]. The study by Yaqoob et al. [127] demonstrated the simultaneous effective removal of OM and COD (up to 84%) and bioremediation of pollutants (up to 90%). The electricity generation behavior observed in both studies was due to the configuration materials used to assemble the electrodes. Furthermore, the characteristics of the substrates, such as chemical composition (e.g., pH; electrical conductivity, EC; and so on), as well as the operating conditions, were factors that influenced the performance of the MFCs in both studies. For example, in the study by Yaqoob et al. [129], the pH and EC of the substrate before application were 7.04 (neutral) and 59 μS/cm (increased by 26% after treatment), respectively, which improved the production of power in the BMFC. The neutral pH of a substrate (or environment) facilitates the development or growth of microorganisms, promoting optimal activity levels on the anode surface [130]. In addition, OM concentrations and the bacterial community play critical roles in improving the performance of MFCs.

Furthermore, in another investigation, an SC-MFC was configured using bamboo charcoal (BC) for the anode electrode and a Pt-coated carbon cloth for the cathode [43]. The working volume of the MFCs was 530, 530, and 500 mL, and they were inoculated with potato-processing wastewater. In one MFC, a maximum current density of 1140 mA/m² was observed. The current density achieved by Sato et al. [43] in potato waste-fed SC-MFC was higher than that in the above studies. This performance could be due to the physicochemical parameters of the substrate (potato waste) and the high EC and low resistance when BC is used as an anode electrode. Other key characteristics of BC include its biocompatibility, high chemical stability, and mechanical strength [43].

In summary, the above findings indicated that potato waste—like other organic substrates—is potentially an excellent alternative, allowing for enhanced power generation and wastewater bioremediation performance when using MFCs. Furthermore, the electrode materials are other aspects to be considered when implementing MFC technology. However, more investigations are required to evaluate the influence of potato wastewater in MFC technological development.

In recent years, great strides have been made regarding the use of BESs, such as MFCs, for the simultaneous treatment of wastewater and production of fuels. This progress has been achieved by combining BES prototypes to improve their process performance. In this line, the use of MFCs for the production of both CH₄ and H₂ has captured the attention of researchers worldwide. Apart from the fact that this technology is environmentally friendly, it is also an excellent option for producing fuels while eliminating pollutants in wastewater. Furthermore, MFC technologies are less expensive, when compared to conventional methods.

Hao et al. [143] have recently constructed an SC-MFC (working volume of 2000 mL) coupled with an anaerobic membrane bioreactor (AnMBR) to enable enhanced CH₄ production. While 40 cm² of carbon felt was utilized as an anode, the cathode was constructed from various materials (e.g., non-woven carbon cloth, platinum carbon, and carbon black). Before assembly of the SCMFC-AnMBR, the carbon felt was sterilized using 1 mol/L HCl and NaOH. The SCMFC-AnMBR was inoculated with synthetic wastewater (SWW) and compared to the conventional one (C-AnMBR). The SWW was added to SCMFC-AnMBR with a concentration ratio of 205:5:1 (C:N:P), and the main components of SWW were: (1) 3000 mg/L of glucose (C₆H₁₂O₆), (2) 120 mg/L of monopotassium phosphate (KH₂PO₄), (3) 120 mg/L of ammonium chloride (NH₄Cl), (4) 112 mg/L of iron chloride (FeCl₂), and (5) 30 mg/L of magnesium sulfate (MgSO₄). The SCMFC-AnMBR indicated high recovery efficiencies of 38.89 mg/L (COD) and 67.84 mg/L (CH₄) and presented a maximum voltage of 107 ± 14 mV.

Additionally, in a previous study by Nguyen et al. [145], single-chamber microbial electrolysis cells (MECs) using a simultaneous dark fermentation (DF) process were constructed. The DF was combined with MECs to form the so-called DF-MEC. Then, the DF-MEC was inoculated with a species of algae called Saccharina japonica (sDFMEC), in order to improve fuel production and accelerate the process. The sDFMEC recorded a maximum production of H₂ of 438.7 ± 13.3 mL/g-TS, outperforming the control (i.e., DF-MEC). At the same time, the sDFMEC system reached maximum CH₄ production and COD removal of 63.1 ± 3.4 mL/g-TS and 75.6 ± 1.4%, respectively. Nonetheless, DF-MEC showed an efficient recovery of 32.2%, achieving a maximum H₂ production of 403.4 mL/g-TS [145]. In contrast, in the study by Gebreslassie et al. [146] a maximum H₂ production of 110 mL/g-VS was reported in a similar sDFMEC. This yield was 3.66 times lower than that reported by Nguyen et al. Later, in an sDFMFC constructed using a surface-modified stainless steel mesh cathode, a higher H₂ production of 408 mL/g-TS was recorded [147]. The authors modified this system to optimize the electrode performance during the DF process. They revealed that anodization (i.e., coating an oxide layer over a metal to make it corrosion-resistant) is the best alternative for improving fuel production using bioelectrochemical systems. These findings indicate that sDFMEC is more effective than the combination of SCMFC-AnMBR for fuel production, due to the significant effect of adding S. japonica into the sDFMEC reactor. However, all of these methods can feasibly improve CH₄ and H₂ production while conducting bioremediation of contaminants from wastewater.

Other strategies used to improve fuel production (i.e., H₂ and CH₄) include the use of other types of substrates, such as biochar, which led to increases in H₂ production of up to 118.5% and in CH₄ of up to 14% [148]. Calcium lignosulfonate-based biochar led to a 50% increase in H₂ [149], a biochar catalyst increased H₂ by 52% [150], and electroactive cultures (EACs) have also been tested. More recently, a DC-MFC was constructed to evaluate the effect of CH₄ injection on anaerobic oxidation (AO)-coupled MFCs (AO-MFCs), in terms of power generation [151]. Two EACs (acetate and formate) were used in the AO-MFCs, in order to improve the performance of the fabricated prototype. For start-up of the system, 84.5 cm² (13 × 6.5 cm) of breathable cloth was used as an anode, while the cathode was made of 81 cm² (9 × 9 cm) of carbon felt, which were separated by an ultrafiltration membrane. The anode chambers were inoculated with 40 mL (0.04 L) of anaerobic sludge. The obtained results indicated that the specific EACs were responsible for converting CH₄ to CO₂ while producing bioelectricity.

Liu et al. [152] have constructed a novel prototype MEC coupled with AD (MEC-AD; working volume 400 mL) operated with few-layer Ti₃C₂TX MXene (FL-MXene), multi-layer Ti₃C₂TX MXene, and MAX phase titanium aluminum carbide (MAX). Subsequently, the reactor was inoculated with cattle manure (CM) and sewage sludge (SS). Furthermore, graphite rods were used for the anode and cathode materials. The MEC-AD operated with a 0.035 wt% of ML-MXene showed a maximum CH₄ production of 358.7 mL/g VS. This result was superior to that reported in MECs (38.4 ± 1.7 mL/g TS) elsewhere [145]. The recorded difference was due to the systems having been configured differently and operated under different environmental conditions.