Please note this is a comparison between versions V2 by Beatrix Zheng and V3 by Wibawa Hendra Saputera.
Methane is one of the promising alternatives to non-renewable petroleum resources since it can be transformed into added-value hydrocarbon feedstocks through suitable reactions. The conversion of methane to methanol with a higher chemical value has recently attracted much attention. The selective oxidation of methane to methanol is often considered a “holy grail” reaction in catalysis. However, methanol production through the thermal catalytic process is thermodynamically and economically unfavorable due to its high energy consumption, low catalyst stability, and complex reactor maintenance. Photocatalytic technology offers great potential to carry out unfavorable reactions under mild conditions. Many in-depth studies have been carried out on the photocatalytic conversion of methane to methanol.
Energy plays a vital role in ensuring national security. It becomes a concern because the demand is growing rapidly along with economic development, population growth, and technological development. Currently, energy resources rely on non-renewable energy, such as fossil fuels (coal, natural gas, and oil). Meanwhile, the availability of these resources is finite and will be vanished if they continue to be exploited unwisely. On the other hand, fossil fuel combustion produces CO2 that will exacerbate global warming.
The global warming issue has attracted a lot of attention. Through the 2015 Paris Agreement, many countries have committed to contributing to climate change mitigation and reducing greenhouse gas emissions. According to Environmental Protection Agency (EPA), methane is the second-largest contributor to climate change accounting for about 10% of all greenhouse gasses emitted in 2019. The Intergovernmental Panel on Climate Change (IPCC) states that comparatively, it has 34 times greater Global Warming Potential (GWP) than carbon dioxide (Figure 1). Methane is emitted from natural sources (wetlands, termites, marine, freshwater, and CH4 hydrate) and human activities (energy, industry, agriculture, land use, and waste management). Globally, 50–65 percent of total methane in the atmosphere emits from human activities.
Figure 1. Global Warming Potential (GWP) of various types of greenhouse gases .
Methane is the simplest hydrocarbon with a symmetric tetrahedral structure leading methane to have low polarizability and low electron and proton affinity . Methane is a very stable and non-reactive substance. Therefore, it is difficult to activate the C-H bond; hence, high pressure and temperature are required. As the main component of natural gas, methane has a high caloric value and is classified as a good hydrogen source. It is converted into various chemicals such as syngas for ammonia production, methanol, hydrocarbon, acetylene, and carbon disulfide. It can also be used directly as fuel by direct combustion (Figure 2).
Methanol and ammonia are the most critical methane conversion products required in large quantities . Liquefaction of methane to methanol is preferred over gaseous methane because the liquid state is easier to handle, store, and transport. Methanol is also vital in the industry since it is used as feedstock for textiles, pharmaceuticals, plastics, and biodiesel. In addition, methanol is clean energy and intermediate source for a wide range of industrial applications (Figure 3). Therefore, converting methane into higher value-added chemicals such as methanol is necessary to develop sustainable energy sources and address global warming issues.
Methanol can be produced by selective oxidation through indirect or direct methods . Industrially, indirect methods are employed for the production of methanol. The process produces intermediate syngas (CO and H2) through steam or dry reforming, then hydrogenated to obtain methanol. However, the syngas process is highly endothermic, requiring a large external energy supply. Therefore, this process still has many drawbacks, such as high energy consumption, complicated operation, catalyst deactivation, and reactor stability . The direct method of methanol production is desirable to reduce production costs because the process bypasses syngas production. However, the target product is still unsatisfactory due to the low selectivity of methanol.
Zakaria and Kamarudin  have summarized several relevant technologies to convert methane into methanol. These include conventional catalytic processes, plasma technology, supercritical water, biological (membrane), and photocatalytic technology. However, some drawbacks are still inevitable, including (i) the relatively slow selectivity of methanol formation for conventional catalytic technology; (ii) low conversion productivity and limited by the amount of methane that can be dissolved in water for plasma technology; (iii) reactor design and high corrosion rate when treating effluents containing halogen for supercritical water processes; (iv) membrane incompatibility due to methane permeability, which can cause dissolution, swelling, or breakage of the membrane; and (v) limitations of investigation of photocatalysts and suitable photoreactors for photocatalytic technology .
It is desirable to synthesize methane at a lower temperature to reduce energy consumption and maintain catalyst stability. Among several technologies, photocatalytic technology seems to be a promising method for the conversion of methane conversion to methanol, as it offers an effective way to produce methanol using renewable solar energy under ambient conditions. Furthermore, photon energy that exceeds activation energy for a specific chemical reaction promotes the redox reaction. Therefore, the involvement of solar energy to facilitate photocatalytic reaction exhibits more environmentally friendly, sustainable, and renewable than fossil fuel-based energy. This technology can also reduce production costs and increase economic benefits. In addition, catalyst deactivation will be significantly reduced due to the low temperature and pressure used (under ambient conditions) in the photocatalytic process.
Figure 4 shows the number of publications on the utilization of photocatalytic technology in general and specifically for converting methane to methanol from 2000 to 2020. The increasing number of scientific publications on photocatalytic technology for methane to methanol conversion provides clear evidence that this topic is significant. In addition, many researchers studied the effect of different structure engineering and nanomaterials on the performance of photocatalysts since their energy conversion efficiency is principally influenced by the physicochemical properties of photocatalysts and operating conditions during the photocatalytic reaction.
Figure 4. The number of research Scopus with TITLE–ABS–KEY photocatalyst–photocatalytic and photocatalyst–methane–methanol.
2. Heterogeneous Photocatalyst for Photo-Oxidation Methane to Methanol
Photocatalysis is commonly referred to as artificial photosynthesis since the photosynthetic system inspires the process. The essence of natural photosynthesis is to drive chemical reactions using optical photon energy. Upon illumination of sunlight, oxygen (O2) is produced from the oxidation of water (H2O) and carbon dioxide (CO2), which further transform to generate hydrocarbons with the help of chlorophylls to absorb and transfer photon energy . The broad definition of photocatalysis can also be adopted from IUPAC, which can be defined as a “Change in the rate of a chemical reaction or its initiation under the action of ultraviolet, visible or infrared radiation in the presence of a substance—the photocatalyst—that absorbs light and is involved in the chemical transformation of the reaction partners.”
Currently, photocatalytic technology has been widely applied to solve problems related to air pollution  and environmental remediation of water contaminants , including dyes degradation , organic pollutants removal , heavy metals removal , and oil degradation in wastewater . In addition, photocatalytic technology provides alternative ways to produce renewable energy, including water splitting, CO2 reduction, N2 fixation, and, in particular, CH4 oxidation to methanol .
2.1. Thermodynamics for Methane to Methanol Conversion
Methane has very stable and strong C-H bonds in the CH4 molecules, which remain challenging to convert methane into more useful hydrocarbon and hydrogen.
Methanol from methane in the industry is produced indirectly from a steam reforming process using a nickel-based catalyst followed by high-pressure catalytic conversion of the synthetic gas to methanol (Figure 5). Steam reforming is an unfavorable thermodynamic reaction and can only be proceeded at high temperature and pressure. Nevertheless, this process can produce H2 with high purity. However, there are still challenges, such as high energy consumption due to the formation of highly endothermic syngas , low catalyst activity, which still needs further development , and complex treatment to prevent heat transfer problems .
Methanol can also be obtained from the direct conversion of methane with water. Thermodynamically, converting methane into methanol using water as a reactant is an endothermic process (ΔH0298 = 77 kJ/mol). However, this process is thermodynamically unfavorable at any temperature, as reflected by the Gibbs free energy data at a temperature range of 273 K to 1500 K. Furthermore, photocatalytic reaction offers an alternative way to facilitate these unfavorable reactions under ambient conditions. The process includes methane and water as the reactant and light as the driving force.
2.2. Proposed Mechanism of Photocatalytic Conversion of Methane to Methanol
The development of the conversion of methane to methanol by photocatalytic technology was initiated by Ogura & Kataoka . The reaction involves water vapor at temperatures below 100 °C, methane gas, and UV irradiation at atmospheric pressure. First, methane gas continuously flowed into the water surface to obtain a mixture of water vapor and methane. Then, the mixture of water vapor and methane reacted and produced methanol as the main product. The brief mechanism of photochemical methane conversion in the research conducted by Ogura and Kataoka  is shown in Equations (1)–(4).
H2O + hv (λ ≥ 185 nm) → H2 + ½ O2
H2O + hv (λ ≥ 185 nm) → 1/2H2 + •OH
CH4 + •OH → •CH3 + H2O
•CH3 + H2O → CH3OH + ½ H2
The reaction begins with the photolysis of water to produce a hydroxyl radical (•OH). The hydroxyl radical then reacts with methane to produce methyl radicals (•CH3). Finally, the methyl radical reacts with other water molecules to produce methanol and hydrogen. Furthermore, Noceti et al.  combined two reactions, including water splitting and methane conversion, to produce methanol and hydrogen using La/WO2-based photocatalyst, as shown briefly in Equations (5)–(10). The reaction was carried out at a temperature of 94 °C, atmospheric pressure, and with visible light irradiation has succeeded in oxidizing methane with water as an oxidizing agent. As a result, the reaction produces methanol and hydrogen with a methane conversion of 4%.
La/WO3 + hv (λ ≥ 410 nm) → e−CB + h+VB
e−CB + MV2+ → MV•+
h+VB + H2O → H+ + •OH
MV•+ + H+ → ½ H2 + MV2+
CH4 + •OH → •CH3 + H2O
•CH3 + H2O → CH3OH + ½ H2
However, the first obstacle in the photocatalytic conversion of methane to methanol is how to activate the highly stable methane molecule. There are two possible scenarios for activating methane using a semiconductor-based catalyst . Methane can be activated directly by photogenerated holes in the VB where •OH is produced by reduction of H2O2 and oxidation of H2O while •O2− produced during the reaction by H2O2 and •OH. Methanol can be obtained by: (i) reaction of methyl radical (•CH3) with •OH, (ii) reaction of •OCH3 with H2O, or (iii) reduction of CH3OOH generated by the integration of •CH3 and O2. Methane can also be activated indirectly by any active oxygenated radical species, as illustrated in Figure 6. This reaction depends on the reaction of the applied system, such as the type of semiconductor and any other additional substance added.
Gondal et al.  proposed a mechanism for methane activation through •OH produced by the photocatalytic process. Several studies have adopted this mechanism, as illustrated in Figure 7a . Xie et al.  proposed a typical reaction of photocatalytic methanol production from methane with simultaneous production of •OH by reduction of H2O2 and •CH3 by oxidation of methane in the VB by the photogenerated hole. Methanol is obtained through the reaction between •CH3 and •OH, which probably occurs in iron species as a dopant. Zeng et al.  proposed a mechanism for converting methane to methanol with the addition of iron ions and H2O2 species called photocatalysis of the Fenton reaction (PCFR) (Figure 7b). The schematic mechanism for selective conversion of methane to methanol can also be achieved, as illustrated in Figure 7c. Zhou  proposed a methane activation mechanism by reducing O2 in the conduction band and oxidation of H2O in the valence band. Methanol will be produced by a direct combination of •CH3 and •OH and reduction of CH3OOH generated by the integration of •CH3 and O2 (Figure 7d). Moreover, the role of each active species, including e−, •O2−, •OH, and h+ was studied by utilizing K2Cr2O7, para-quinone, salicylic acid and Na2C2O4 as scavengers to trap those active species formed in the PCFR process, respectively (Figure 8). Based on these findings, e− played the most dominant role in methanol production, followed by •O2−, •OH, and h+.
Based on several studies, it is found that the hydroxyl radical plays a crucial role in the photocatalytic conversion of methane to methanol. This species can be obtained either by photooxidation of H2O or photoreduction of H2O2. In general, H2O2 is added to facilitate the formation of •OH and, thus, enhance photocatalytic efficiency. For example, Noceti et al.  reported that adding H2O2 to the reaction carried out at atmospheric pressure, and temperature of 94 °C with irradiation from a mercury lamp (46% visible light) increased methane conversion from 4% to 10%, accompanied by increased CO2 formation. Zeng et al.  also reported excellent results in reactions using TiO2 photocatalyst and addition of H2O2 under visible light irradiation, with methanol yields up to 850 mol g−1 h−1 and a selectivity of 83%.
On the other hand, a study conducted by Gondal et al.  showed the opposite effect, where the addition of H2O2 exhibited a lower yield of methanol than the reaction without H2O2 addition using WO3 photocatalyst under visible laser irradiation and ambient conditions. These results are believed to be due to the usage of a visible laser lamp providing higher photon flux density monochromatic light than the conventional lamp so that more •OH was formed. These •OH radicals are also a major source of O2 that facilitates further oxidation of methanol. These results agree with Villa et al. , which carried out a reaction using WO3 photocatalyst at atmospheric pressure, the temperature of 55 °C, and under UVC-Vis irradiation. It was found that the formation of ethane accompanied the methanol production due to the higher amount of •OH activated methane to generate more •CH3, as shown in Equation (11).
•CH3+ •CH3 → C2H6
Based on these findings, Villa et al.  proposed a strategy to incorporate fluorine on the WO3 photocatalyst surface to minimize the interaction between the catalyst and the reactants. The schematic reaction mechanism on the surface of the WO3 before and after the incorporation of fluorine is shown in Figure 9. It was found that •OH groups on the catalyst surface are mainly responsible for enhancing the performance of WO3 in the selective oxidation of methane to methanol. At the same time, an enormous amount of free OH radicals favor the formation of ethane. Therefore, adding a hydroxyl radical generator, i.e., H2O2, can increase methane conversion . However, such an appropriate amount of H2O2 is essential for controlling the selectivity of methanol .
Methanol, the primary desired main product of methane oxidation, is more reactive than methane itself. Thus, methanol can be easily oxidized further when some of the following conditions occur, such as:
1. The formation of superoxide radicals (•O2−) produced via the reduction of O2 in CB of semiconductor , shown in Equations (12)–(14).
O2 + e− → O2•−
CH3OH + O2•− → CO2 + H2O + e−
CH4 + 2O•− → CO2 + H2O + 2e−
2. A sufficient amount of methanol generation either competes with water to further react with a photogenerated hole in VB or direct interaction with •OH to produce side products such as formaldehyde , as shown in Equations (15)–(17)
CH3OH + h+ → CH3OH+ → H2CO + H• + H+
H2CO + h+ → CO + H• + H+
CH3OH + •OH → CH2O + H• + H2O
According to the abovementioned issues, it is essential to control the oxidative power of the system to achieve optimum methanol selectivity. For instance, using a moderate photocatalyst lowers the potential reduction of H2O2 and prevents O2 reduction to form •O2− by adding an electron scavengers agent . In addition, the yield of methanol can be enhanced by continuous removal of the methanol after its formation to prevent further oxidation of methanol .
United States Environmental Protection Agency. Understanding Global Warming Potentials. Available online: https://www.epa.gov/ghgemissions/understanding-global-warming-potentials (accessed on 5 June 2022).
Song, H.; Meng, X.; Wang, Z.J.; Liu, H.; Ye, J. Solar-Energy-Mediated Methane Conversion. Joule 2019, 3, 1606–1636.
Holmen, A. Direct conversion of methane to fuels and chemicals. Catal. Today 2009, 142, 2–8.
Dalena, F.; Senatore, A.; Marino, A.; Gordano, A.; Basile, M.; Basile, A. Methanol Production and Applications: An Overview. In Methanol; Elsevier B.V.: Amsterdam, The Netherlands, 2018; pp. 3–28.
Sharma, R.; Poelman, H.; Marin, G.B.; Galvita, V.V. Approaches for selective oxidation of methane to methanol. Catalysts 2020, 10, 194.
Lunsford, J.H. Catalytic conversion of methane to more useful chemicals and fuels: A challenge for the 21st century. Catal. Today 2000, 63, 165–174.
Zhang, Q.; He, D.; Zu, Q. Recent Progress in Direct Partial Oxidation of Methane to Methanol. Catal. Surv. Asia 2012, 16, 53–61.
Zakaria, Z.; Kamarudin, S.K. Direct conversion technologies of methane to methanol: An overview. Renew. Sustain. Energy Rev. 2016, 65, 250–261.
Yang, X.; Wang, D. Photocatalysis: From Fundamental Principles to Materials and Applications. ACS Appl. Energy Mater. 2018, 1, 6657–6693.
Binas, V.; Venieri, D.; Kotzias, D.; Kiriakidis, G. Modified TiO2 based photocatalysts for improved air and health quality. J. Mater. 2017, 3, 3–16.
Xu, P.; Zeng, G.M.; Huang, D.L.; Feng, C.L.; Hu, S.; Zhao, M.H.; Lai, C.; Wei, Z.; Huang, C.; Xie, G.X.; et al. Use of iron oxide nanomaterials in wastewater treatment: A review. Sci. Total Environ. 2012, 424, 1–10.
Muraro, P.C.L.; Mortari, S.R.; Vizzotto, B.S.; Chuy, G.; dos Santos, C.; Brum, L.F.W.; da Silva, W.L. Iron oxide nanocatalyst with titanium and silver nanoparticles: Synthesis, characterization and photocatalytic activity on the degradation of Rhodamine B dye. Sci. Rep. 2020, 10, 3055.
Wang, C.C.; Li, J.R.; Lv, X.L.; Zhang, Y.Q.; Guo, G. Photocatalytic organic pollutants degradation in metal-organic frameworks. Energy Environ. Sci. 2014, 7, 2831–2867.
Saputera, W.H.; Amri, A.F.; Devianto, H.; Sasongko, D. Photocatalytic Degradation of Palm Oil Mill Effluent (POME) Waste Using BiVO4 Based Catalysts. Molecules 2021, 26, 6225.
Saputera, W.H.; Tahini, H.A.; Lovell, E.C.; Tan, T.H.; Rawal, A.; Aguey-Zinsou, K.-F.; Friedmann, D.; Smith, S.C.; Amal, R.; Scott, J. Cooperative defect-enriched SiO2 for oxygen activation and organic dehydrogenation. J. Catal. 2019, 376, 168–179.
Le, A.T.; Pung, S.Y.; Sreekantan, S.; Matsuda, A.; Huynh, D.P. Mechanisms of removal of heavy metal ions by ZnO particles. Heliyon 2019, 5, e01440.
Tetteh, E.K.; Rathilal, S.; Naidoo, D.B. Photocatalytic degradation of oily waste and phenol from a local South Africa oil refinery wastewater using response methodology. Sci. Rep. 2020, 10, 8850.
Chen, L.; Qi, Z.; Zhang, S.; Su, J.; Somorjai, G.A. Catalytic hydrogen production from methane: A review on recent progress and prospect. Catalysts 2020, 10, 858.
Ogura, K.; Kataoka, M. Photochemical conversion of methane. J. Mol. Catal. 1988, 43, 371–379.
Yuliati, L.; Yoshida, H. Photocatalytic conversion of methane. Chem. Soc. Rev. 2008, 37, 1592–1602.
Gondal, M.A.; Hameed, A.; Yamani, Z.H.; Arfaj, A. Photocatalytic transformation of methane into methanol under UV laser irradiation over WO3, TiO2 and NiO catalysts. Chem. Phys. Lett. 2004, 392, 372–377.
Villa, K.; Murcia-López, S.; Andreu, T.; Morante, J.R. On the role of WO3 surface hydroxyl groups for the photocatalytic partial oxidation of methane to methanol. Catal. Commun. 2015, 58, 200–203.
Negishi, Y.; Watanabe, S.; Aoki, M.; Hossain, S.; Kurashige, W. Toward the Creation of Highly Active Photocatalysts That Convert Methane into Methanol Active Photocatalysts. Antimicrob. Agents Chemother. 2019, 32, 1854–1858.
Xie, J.; Jin, R.; Li, A.; Bi, Y.; Ruan, Q.; Deng, Y.; Zhang, Y.; Yao, S.; Sankar, G.; Ma, D.; et al. Highly selective oxidation of methane to methanol at ambient conditions by titanium dioxide-supported iron species. Nat. Catal. 2018, 1, 889–896.
Zeng, Y.; Liu, H.C.; Wang, J.S.; Wu, X.Y.; Wang, S.L. Synergistic photocatalysis-Fenton reaction for selective conversion of methane to methanol at room temperature. Catal. Sci. Technol. 2020, 10, 2329–2332.
Zhou, W.; Qiu, X.; Jiang, Y.; Fan, Y.; Wei, S.; Han, D.; Niu, L.; Tang, Z. Highly selective aerobic oxidation of methane to methanol over gold decorated zinc oxide: Via photocatalysis. J. Mater. Chem. A 2020, 8, 13277–13284.
Gondal, M.A.; Hameed, A.; Suwaiyan, A. Photo-catalytic conversion of methane into methanol using visible laser. Appl. Catal. A 2003, 243, 165–174.
Villa, K.; Murcia-López, S.; Morante, J.R.; Andreu, T. An insight on the role of La in mesoporous WO3 for the photocatalytic conversion of methane into methanol. Appl. Catal. B Environ. 2016, 187, 30–36.
López-Martín, Á.; Caballero, A.; Colón, G. Photochemical methane partial oxidation to methanol assisted by H2O2. J. Photochem. Photobiol. A Chem. 2017, 349, 216–223.
Hameed, A.; Ismail, I.M.I.; Aslam, M.; Gondal, M.A. Photocatalytic conversion of methane into methanol: Performance of silver impregnated WO3. Appl. Catal. A Gen. 2014, 470, 327–335.