All-Solid-State Batteries | Encyclopedia MDPI

All-Solid-State Batteries: Comparison

Please note this is a comparison between Version 1 by Gene Yang and Version 2 by Conner Chen.

All-solid-state batteries (SSBs) are one of the most fascinating next-generation energy storage systems that can provide improved energy density and safety for a wide range of applications from portable electronics to electric vehicles. The development of SSBs was accelerated by the discovery of new materials and the design of nanostructures. In particular, advances in the growth of thin-film battery materials facilitated the development of all solid-state thin-film batteries (SSTFBs)—expanding their applications to microelectronics such as flexible devices and implantable medical devices. However, critical challenges still remain, such as low ionic conductivity of solid electrolytes, interfacial instability and difficulty in controlling thin-film growth. In this review, we discuss the evolution of electrode and electrolyte materials for lithium-based batteries and their adoption in SSBs and SSTFBs. We highlight novel design strategies of bulk and thin-film materials to solve the issues in lithium-based batteries. We also focus on the important advances in thin-film electrodes, electrolytes and interfacial layers with the aim of providing insight into the future design of batteries. Furthermore, various thin-film fabrication techniques are also covered in this review.

lithium-ion batteries
solid electrolytes
all solid-state batteries
all solid-state thin-film batteries
nanostructured thin films
interfacial buffer layers
thin-film techniques
thin-film electrodes
thin-film electrolytes

1. Introduction

Lithium-ion batteries (LIBs) are one of the great successes of electrochemical energy storage devices utilized in diverse applications such as portable electronics, hybrid automobiles and even large-scale electrical power storage systems ^[1][2][3][4]. Since the first market emergence of LIBs in the 1990s, the performance of LIBs has been remarkably improved to meet the increasing demand for new energy storage systems with high energy density, high power density, long cycle life and a wide range of operating temperatures ^[5][6]. Moreover, rechargeable batteries are rapidly expanding to drivetrains ^[7][8], as can be seen from the quadrupled global sales of plug-in light vehicles from 0.55 to 2.21 million cars annually from 2015 to 2019 ^[9]. Thus, developing revolutionary energy storage systems is a critical task in today’s energy-dependent society.

Lithium-ion batteries (LIBs) are one of the great successes of electrochemical energy storage devices utilized in diverse applications such as portable electronics, hybrid automobiles and even large-scale electrical power storage systems [1,2,3,4]. Since the first market emergence of LIBs in the 1990s, the performance of LIBs has been remarkably improved to meet the increasing demand for new energy storage systems with high energy density, high power density, long cycle life and a wide range of operating temperatures [5,6]. Moreover, rechargeable batteries are rapidly expanding to drivetrains [7,8], as can be seen from the quadrupled global sales of plug-in light vehicles from 0.55 to 2.21 million cars annually from 2015 to 2019 [9]. Thus, developing revolutionary energy storage systems is a critical task in today’s energy-dependent society.

LIBs are composed of a cathode and an anode separated by an electrolyte. During discharging, the lithium ions (Li

⁺

) migrate through the electrolyte from the anode to the cathode and a discharging current flows through the external circuit, whereas the use of electrical energy pushes the electrons and Li

⁺ back to the anode during the charging process. Most of the commercial LIBs employ liquid electrolytes owing to their large electrochemical voltage windows, high ionic conductivities and great wettability with the internal components of LIBs ^[10]. Generally, the liquid electrolyte is a mixture of linear and cyclic carbonate-based organic solvents such as diethyl carbonate (DEC) ^[11], ethyl methyl carbonate (EMC) ^[11][12][13], dimethyl carbonate (DMC) ^[11][12], ethylene carbonate (EC) ^[12][13][14], propylene carbonate (PC) ^[11], and lithium salt such as lithium hexafluorophosphate (LiPF

back to the anode during the charging process. Most of the commercial LIBs employ liquid electrolytes owing to their large electrochemical voltage windows, high ionic conductivities and great wettability with the internal components of LIBs [10]. Generally, the liquid electrolyte is a mixture of linear and cyclic carbonate-based organic solvents such as diethyl carbonate (DEC) [11], ethyl methyl carbonate (EMC) [11,12,13], dimethyl carbonate (DMC) [11,12], ethylene carbonate (EC) [12,13,14], propylene carbonate (PC) [11], and lithium salt such as lithium hexafluorophosphate (LiPF

₆

), lithium hexafluoroarsenate monohydrate (LiAsF

₆

), lithium perchlorate (LiClO

₄

) and lithium tetrafluoroborate (LiBF

₄) ^[13][15][16]. However, these liquid electrolytes have severe drawbacks ^[17], including high flammability, narrow electrochemical stability windows, limited operating temperatures and irreversible decomposition. Due to their high flammability, organic liquid electrolytes are believed to be the main reason for fires and explosions in LIBs ^[18]. In addition, the formation of lithium dendrites with organic liquid electrolytes ^[19] leads to internal short circuits causing catastrophic failure of lithium-based batteries ^[20]. Therefore, developing alternative battery systems to prevent such issues of the liquid electrolytes as well as to provide high energy density and power is indispensable.

) [13,15,16]. However, these liquid electrolytes have severe drawbacks [17], including high flammability, narrow electrochemical stability windows, limited operating temperatures and irreversible decomposition. Due to their high flammability, organic liquid electrolytes are believed to be the main reason for fires and explosions in LIBs [18]. In addition, the formation of lithium dendrites with organic liquid electrolytes [19] leads to internal short circuits causing catastrophic failure of lithium-based batteries [20]. Therefore, developing alternative battery systems to prevent such issues of the liquid electrolytes as well as to provide high energy density and power is indispensable.

All-solid-state batteries (SSBs), which use non-volatile solid electrolytes, have emerged as an alternative battery system to replace the conventional LIBs with liquid electrolytes ^[21][22][23]. Not only are SSBs inherently safer owing to the lack of flammable organic components, SSBs also have a large electrochemical stability window, thus enabling a dramatic improvement in the energy density ^[24][25][26]. Furthermore, the SSBs have much higher power and energy characteristics compared with various batteries which are currently being developed as next-generation batteries ^[27][28]. The electrodes are required to have the following features in order to achieve high energy density: (i) high gravimetric capacity (in Ah/kg) and volumetric capacity (in Ah/L), i.e., a high number of electrons transferred per unit of reaction; (ii) high (cathode) and low (anode) standard redox potential of the respective electrode redox reaction, leading to high cell voltage. Moreover, electrochemical reactions in rechargeable cells at both anode and cathode electrodes must be highly reversible to maintain the capacity for thousands of cycles. Recent studies, therefore, have focused on developing new electrode materials ^[29][30] or engineering electrode architectures ^[31][32] to increase the energy density of SSBs. Among various attractive candidate materials for electrodes, the selection of cathode materials depends on the battery type, i.e., Li

All-solid-state batteries (SSBs), which use non-volatile solid electrolytes, have emerged as an alternative battery system to replace the conventional LIBs with liquid electrolytes [21,22,23]. Not only are SSBs inherently safer owing to the lack of flammable organic components, SSBs also have a large electrochemical stability window, thus enabling a dramatic improvement in the energy density [24,25,26]. Furthermore, the SSBs have much higher power and energy characteristics compared with various batteries which are currently being developed as next-generation batteries [27,28]. The electrodes are required to have the following features in order to achieve high energy density: (i) high gravimetric capacity (in Ah/kg) and volumetric capacity (in Ah/L), i.e., a high number of electrons transferred per unit of reaction; (ii) high (cathode) and low (anode) standard redox potential of the respective electrode redox reaction, leading to high cell voltage. Moreover, electrochemical reactions in rechargeable cells at both anode and cathode electrodes must be highly reversible to maintain the capacity for thousands of cycles. Recent studies, therefore, have focused on developing new electrode materials [29,30] or engineering electrode architectures [31,32] to increase the energy density of SSBs. Among various attractive candidate materials for electrodes, the selection of cathode materials depends on the battery type, i.e., Li

⁺ or Li-metal batteries. In the case of LIBs, air-stable lithium-based intercalation compounds should be used as a cathode due to the absence of lithium in the anode ^[33][34][35]. On the contrary, for Li-metal batteries, the cathode does not need to be lithiated before cell assembly owing to the use of metallic lithium as an anode ^[36]. Among a large number of materials proposed for the cathode in LIBs, transition metal oxides have been recognized as one of the most promising cathode materials ^[37][38][39]. For the anode, graphitic carbon allotropes were mostly used in LIBs, but the use of lithium metal can significantly increase the volumetric energy density by up to 70% with respect to graphite ^[40][41]. However, lithium metal electrodes encounter formidable challenges such as uncontrollable dendrite growth and high reactivity with solid electrolytes, which hampers the use of lithium metal electrodes ^[20]. Alternatively, recent studies of anode materials have focused on lithium transition metal oxides, vanadium oxides or lithium metal nitrides ^[42][43][44]. One of the key features of SSBs is replacing liquid electrolytes with solid electrolytes, which can dramatically enhance the safety of batteries. In order to replace the current organic liquid electrolytes, solid-state electrolytes need to possess high ionic conductivity, negligible electronic conductivity and good stability in contact with the anode and cathode electrodes ^[45][46]. Many different types of inorganic solid electrolytes—Na superionic conductor (NASICON) ^[47], perovskite ^[48], lithium phosphorous oxy-nitride (LiPON) ^[49][50][51], sulfide ^[52][53] and garnet ^[54][55][56]—are widely studied in SSBs.

or Li-metal batteries. In the case of LIBs, air-stable lithium-based intercalation compounds should be used as a cathode due to the absence of lithium in the anode [33,34,35]. On the contrary, for Li-metal batteries, the cathode does not need to be lithiated before cell assembly owing to the use of metallic lithium as an anode [36]. Among a large number of materials proposed for the cathode in LIBs, transition metal oxides have been recognized as one of the most promising cathode materials [37,38,39]. For the anode, graphitic carbon allotropes were mostly used in LIBs, but the use of lithium metal can significantly increase the volumetric energy density by up to 70% with respect to graphite [40,41]. However, lithium metal electrodes encounter formidable challenges such as uncontrollable dendrite growth and high reactivity with solid electrolytes, which hampers the use of lithium metal electrodes [20]. Alternatively, recent studies of anode materials have focused on lithium transition metal oxides, vanadium oxides or lithium metal nitrides [42,43,44]. One of the key features of SSBs is replacing liquid electrolytes with solid electrolytes, which can dramatically enhance the safety of batteries. In order to replace the current organic liquid electrolytes, solid-state electrolytes need to possess high ionic conductivity, negligible electronic conductivity and good stability in contact with the anode and cathode electrodes [45,46]. Many different types of inorganic solid electrolytes—Na superionic conductor (NASICON) [47], perovskite [48], lithium phosphorous oxy-nitride (LiPON) [49,50,51], sulfide [27,52,53] and garnet [54,55,56]—are widely studied in SSBs.

With the development of SSBs, all-solid-state thin-film batteries (SSTFBs) have received significant attention in recent years ^[57][58][59] that can be used for low power microelectronic devices (e.g., implantable medical devices) and energy harvesting technologies ^[60]. Similar to conventional LIBs, SSTFBs consist of a cathode, an anode and an electrolyte. Owing to the difference in chemical potentials of lithium in the two electrodes, the transfer of Li

With the development of SSBs, all-solid-state thin-film batteries (SSTFBs) have received significant attention in recent years [57,58,59] that can be used for low power microelectronic devices (e.g., implantable medical devices) and energy harvesting technologies [60]. Similar to conventional LIBs, SSTFBs consist of a cathode, an anode and an electrolyte. Owing to the difference in chemical potentials of lithium in the two electrodes, the transfer of Li

⁺ from the anode through the electrolyte into the cathode (discharge) delivers energy, whereas the reverse lithium transfer (charge) consumes energy. One unique feature of SSTFBs is the usage of nanostructured thin films and thus SSTFBs can significantly reduce the transport distance of charge carriers, enhancing the kinetics of lithium storage ^[61][62]. Furthermore, the overall performance of SSTFBs can be controlled by modulating the physical and chemical properties of thin films. In order to make SSTFBs, all the battery components need to be fabricated into multilayered thin films by suitable thin-film techniques.

from the anode through the electrolyte into the cathode (discharge) delivers energy, whereas the reverse lithium transfer (charge) consumes energy. One unique feature of SSTFBs is the usage of nanostructured thin films and thus SSTFBs can significantly reduce the transport distance of charge carriers, enhancing the kinetics of lithium storage [61,62]. Furthermore, the overall performance of SSTFBs can be controlled by modulating the physical and chemical properties of thin films. In order to make SSTFBs, all the battery components need to be fabricated into multilayered thin films by suitable thin-film techniques.

While SSBs and SSTFBs have shown their potential as the next major advances beyond LIBs, their performances have not yet been reached the practical level mainly due to the limits of intrinsic material properties. Therefore, understanding and controlling the properties of electrode and electrolyte materials will provide insight into the enhancement of the next-generation battery performances.

2. Electrodes and Electrolytes for Lithium-Based Batteries

As described earlier, the alleviation of safety concerns by using solid electrolytes is the key feature of SSBs. Moreover, solid electrolytes exhibit a large electrochemical window (up to five volts), which can enable the utilization of high voltage cathode materials as well as lithium metal anode.

2.1. Electrodes

Selecting electrode materials for the next generation of batteries needs careful considerations with regards to safety, energy density, cost, cyclability, crustal abundance and recyclability. Electrode chemistries which rely on the mining of rare elements and the utilization of complex ceramic processing greatly diminish the sustainability of an electrode material ^[63]. In addition to the extraction and processing of raw materials, a holistic approach considering the electrode synthesis and device fabrication must be taken into the actual energy cost of battery fabrications.

Selecting electrode materials for the next generation of batteries needs careful considerations with regards to safety, energy density, cost, cyclability, crustal abundance and recyclability. Electrode chemistries which rely on the mining of rare elements and the utilization of complex ceramic processing greatly diminish the sustainability of an electrode material [83]. In addition to the extraction and processing of raw materials, a holistic approach considering the electrode synthesis and device fabrication must be taken into the actual energy cost of battery fabrications.

2.2. Solid Electrolytes

Due to the lack of liquid electrolytes with electrochemical windows above 5 V, until now, the selection of electrode materials has been limited. However, recent advances in developing inorganic solid electrolytes have demonstrated the possibility of using other electrode materials. Ideal inorganic solid electrolytes are required to have thermal/chemical stability, high ionic conductivity and long cycle life. Table 3 shows a summary of ionic conductivities for several solid inorganic electrolytes. In particular, oxide materials, which present excellent stability in ambient conditions, are promising solid electrolytes for SSBs.

The NASICON structure, standing for Na

⁺ superionic conductors, was reported by Hangman et al. in 1968 ^[64]. It has a rhombohedral structure (space group R-3c) made of the framework of octahedra (MO

superionic conductors, was reported by Hangman et al. in 1968 [199]. It has a rhombohedral structure (space group R-3c) made of the framework of octahedra (MO

₆

, M = divalent to pentavalent transition metal ions) and tetrahedra (XO

₄

, X = P, Si, As). Two MO

₆

octahedra and three PO

₄

tetrahedra share oxygen atoms, which are assembled to form a 3D network structure. This structure provides a 3D interconnected conduction pathway for mobile ions, most commonly Na

⁺

or Li

⁺ ^[65]. The NASICON structure can have a wide range of compositional varieties, leading to varied ionic conductivities. The most promising NASICON-type Li

[200]. The NASICON structure can have a wide range of compositional varieties, leading to varied ionic conductivities. The most promising NASICON-type Li

⁺

conductors are LiTi

₂

(PO

₄

)

₃

and LiGe

₂

(PO

₄

)

₃ with Al substitutions. Arbi et al. ^[66] reported the synthesis of Li

with Al substitutions. Arbi et al. [174] reported the synthesis of Li

_1+x

_2−x

(PO

₄

)

₃

(LATP) and Li

_1+x

_2−x

(PO

₄

)

₃

(LAGP) conductors (0 ≤ x ≤ 0.5) giving conductivities of 3.4 × 10

⁻³

S/cm (LATP, x = 0.2) and 10

⁻⁴ S/cm (LAGP, x = 0.2) at room temperature. By enhancing the crystallization of LAGP, Thokchom et al. ^[67] reported a conductivity of 4.22 × 10

S/cm (LAGP, x = 0.2) at room temperature. By enhancing the crystallization of LAGP, Thokchom et al. [175] reported a conductivity of 4.22 × 10

⁻³

S/cm at room temperature. Although its high ionic conductivity is attractive, the instability of LATP in contact with Li metal due to the reduction of Ti

⁴⁺ requires an additional protective layer. Furthermore, expensive precursors to synthesize LAGP would require the substitution of Ge. As prototype cells, LAGP was used for a Li protection membrane for aqueous Li–air batteries ^[68][69].

requires an additional protective layer. Furthermore, expensive precursors to synthesize LAGP would require the substitution of Ge. As prototype cells, LAGP was used for a Li protection membrane for aqueous Li–air batteries [201,202].

By the 1980s, a considerable amount of work had been done on inorganic solid lithium superionic conductors, Li

_4±x

_1−x

₄ (X = P, Al or Ge, LISICON) ^[70]. LISICON is based on the γ-Li

(X = P, Al or Ge, LISICON) [203]. LISICON is based on the γ-Li

₃

₄

structure that is expected to diffuse Li

⁺

through the vacancy mechanism in its pure state. The ionic conductivity of Li

₁₄

ZnGe

₄

₁₆

was limited to 10

⁻⁷

S/cm at room temperature and had reactivity with Li anode or atmospheric CO

₂ ^[71]. Kuwano and West in 1980 reported much higher ionic conductivity for Li

[204]. Kuwano and West in 1980 reported much higher ionic conductivity for Li

₄

GeO

₄

–Li

₃

₄

systems with a total ionic conductivity of 4 × 10

⁻⁵ S/cm at 18 °C with the addition of an interstitial diffusion mechanism ^[72]. The introduction of V

S/cm at 18 °C with the addition of an interstitial diffusion mechanism [176]. The introduction of V

⁵⁺

(e.g., Li

_3+x

_1−x

₄

) contributed to stabilizing the structure in the presence of CO

₂

in air. It is also reported that the Li

₄

SiO

₄

–Li

₃

₄

solid solution presented the ionic conductivity 10

⁻⁶ S/cm at room temperature and had better stability against Li due to the absence of transition metal ions. While maintaining the chemical stability in Li

S/cm at room temperature and had better stability against Li due to the absence of transition metal ions [75]. While maintaining the chemical stability in Li

₄

Si/GeO

₄

–Li

₃

₄

solid solution, the ionic conductivity could be further improved to ~10

⁻⁵ S/cm by substituting O with Cl, enlarging the four oxygen bottleneck size and lowering the diffusion barriers ^[73]. The most significant conductivity improvement of the LISICON structure was achieved with O replacement with larger and better polarizing ions, S, to form thio-LISICON. For example, the Li

S/cm by substituting O with Cl, enlarging the four oxygen bottleneck size and lowering the diffusion barriers [177]. The most significant conductivity improvement of the LISICON structure was achieved with O replacement with larger and better polarizing ions, S, to form thio-LISICON. For example, the Li

₂

S–GeS2–P

₂

₅

system (Li

_3.25

_0.25

_0.75

₄

, called LGPS) reached a high ionic conductivity of 2.2 × 10

⁻³ S/cm at room temperature ^[74]. However, the high sensitivity to moisture in air and difficulties in the synthesis of sulfide electrolytes remain as challenges.

S/cm at room temperature [178]. However, the high sensitivity to moisture in air and difficulties in the synthesis of sulfide electrolytes remain as challenges.

In 1992, Bates et al. ^[75] reported the synthesis of lithium phosphorus oxynitride (LiPON, Li

In 1992, Bates et al. [179] reported the synthesis of lithium phosphorus oxynitride (LiPON, Li

_3.3

_3.9

_0.17

) by RF-magnetron sputtering of Li

₃

₄

, which showed conductivity of 2 × 10

⁻⁶ S/cm at 25 °C. Different from other electrolytes, LiPON has an amorphous structure, and its ionic conductivity is significantly affected by the amount of nitrogen ^[76][77][78]. Another route to improve the ionic conductivity of LiPON is to increase the Li concentration, as can be seen by the conductivity increase to 6.4 × 10

S/cm at 25 °C. Different from other electrolytes, LiPON has an amorphous structure, and its ionic conductivity is significantly affected by the amount of nitrogen [180,181,205]. Another route to improve the ionic conductivity of LiPON is to increase the Li concentration, as can be seen by the conductivity increase to 6.4 × 10

⁻⁶

S/cm at 25 °C when LiPON was deposited with Li

₂

O in addition to Li

₃

₄. Because of its easy deposition in thin films, LiPON can present a low resistance in the form of a thin film. Thus, LiPON is commonly used as the electrolyte for thin-film microbatteries (1–10 mAh) that can be used for smart cards, wearable devices, MEMS or implantable medical devices ^[79][80]. The deposition of LiPON and prototype battery performance will be discussed in detail later.

. Because of its easy deposition in thin films, LiPON can present a low resistance in the form of a thin film. Thus, LiPON is commonly used as the electrolyte for thin-film microbatteries (1–10 mAh) that can be used for smart cards, wearable devices, MEMS or implantable medical devices [205,206,207]. The deposition of LiPON and prototype battery performance will be discussed in detail later.

Among perovskite-type solid electrolyte materials, Li

_2/3−1/3x

TiO

₃ (LLTO) exhibited very high bulk ionic conductivity. The LLTO is composed of the ideal structure cubic phase α-LLTO with Pm3 m symmetry and tetragonal phase β-LLTO with a P4/mmm space group. In 1993, Inaguma et al. ^[81] showed the improved ionic conductivity of Li

(LLTO) exhibited very high bulk ionic conductivity. The LLTO is composed of the ideal structure cubic phase α-LLTO with Pm3 m symmetry and tetragonal phase β-LLTO with a P4/mmm space group. In 1993, Inaguma et al. [182] showed the improved ionic conductivity of Li

_0.34

_0.51

TiO

_2.94

compared to LISICON. The bulk and grain boundary activation energies of the cubic perovskite structure were reported to be E

= 0.40 eV and E

_gb

= 0.42 eV, respectively. Importantly, the bulk ionic conductivity was reported to be 1 × 10

⁻³

S/cm at room temperature, but the total ionic conductivity was 2 × 10

⁻⁵ S/cm due to the high grain boundary resistance. Alonso et al. ^[82] identified the position of Li

S/cm due to the high grain boundary resistance. Alonso et al. [208] identified the position of Li

⁺

in Li

_0.5

TiO

₃

using the neutron powder diffraction and suggested the Li

⁺ conduction pathway in LLTO. Jay et al. ^[83] proposed an additional diffusion pathway in the c-direction via a computational study that aligned more directly with experimental data. Lu et al. ^[84] synthesized Li

conduction pathway in LLTO. Jay et al. [209] proposed an additional diffusion pathway in the c-direction via a computational study that aligned more directly with experimental data. Lu et al. [183] synthesized Li

_2x−y

_1-x−y

TiO

₃

to enhance the Li

⁺

diffusion by increasing A site. With the composition of Li

_15/56

_1/16

_15/28

TiO

₃

a total conductivity of 4.84 × 10

⁻⁴ S/cm was achieved with an activation energy of just 0.29 eV.

S/cm was achieved with an activation energy of just 0.29 eV.

Although its high bulk ionic conductivity is attractive, LLTO suffers from high grain boundary resistance and reactivity with Li metal. LLTO variants showed distinct discoloration when in contact with Li metal, and the Li intercalation at 1.7 V vs. Li/Li

⁺ into LLTO was observed, limiting their use with low potential anode materials ^[85][86][87]. To resolve the instability issue of LLTO with Li, Ti

into LLTO was observed, limiting their use with low potential anode materials [210,211,212]. To resolve the instability issue of LLTO with Li, Ti

⁴⁺

was substituted with Ge

⁴⁺ ^[88] or Zr

[184] or Zr

⁴⁺

and Ta

⁵⁺ ^[89] extending the cathodic stability limit of perovskites to 0–1 V vs. Li/Li

[185] extending the cathodic stability limit of perovskites to 0–1 V vs. Li/Li

⁺.

3. Interfacial Phenomena between Solid-State Electrolytes and Electrodes

As described in previous sections, substantial effort has been devoted to developing high energy and power density electrodes, solid-state electrolytes with high ionic conductivity, good chemical stability and large electrochemical stability windows. However, the performance enhancement of batteries can be insignificant despite the dramatically enhanced performance of an individual component, i.e., electrodes or electrolytes. More importantly, the power density and cycle life of SSBs still have not met the requirements for practical applications. Such poor performances are mainly attributed to the large interfacial resistance between solid electrolytes and electrodes ^{[90][91][92][93]} that originates from the mechanical force development or chemical composition changes. These configurational and chemical changes driven by electrochemical reactions are summarized in

As described in previous sections, substantial effort has been devoted to developing high energy and power density electrodes, solid-state electrolytes with high ionic conductivity, good chemical stability and large electrochemical stability windows. However, the performance enhancement of batteries can be insignificant despite the dramatically enhanced performance of an individual component, i.e., electrodes or electrolytes. More importantly, the power density and cycle life of SSBs still have not met the requirements for practical applications. Such poor performances are mainly attributed to the large interfacial resistance between solid electrolytes and electrodes [227,228,229,230] that originates from the mechanical force development or chemical composition changes. These configurational and chemical changes driven by electrochemical reactions are summarized in

Figure 1 ^[94][95]. We will discuss mechanical and chemical factors associated with the large interfacial resistance in the following section.

7 [231,232]. We will discuss mechanical and chemical factors associated with the large interfacial resistance in the following section.

Figure 17. Schematic diagram of lithium metal battery and electrode/electrolyte interface issues.

Mechanically driven interfacial resistance between solid electrolytes and electrodes originates from poor contact between two rigid materials and the volume changes of electrodes during the charge–discharge process ^[96]. This poor contact eventually leads to the formation and propagation of cracks ^[97] as well as the delamination of interfaces ^[98][99]. Sulfide-based electrolytes possess good mechanical ductility, thus can maintain good contact with electrodes without the degradation of the interfacial contact resistance ^[100]. In contrast, oxide-based electrolytes suffer from the poor adhesion of interfaces with electrodes as most ceramics are vulnerable to cracking due to the low ductility ^[101][102]. The insufficient mechanical contact results in the delamination or “dead” area induced by isolated electrode contact points from solid electrolytes. Due to the lack of conduction paths, neither electrons nor Li

Mechanically driven interfacial resistance between solid electrolytes and electrodes originates from poor contact between two rigid materials and the volume changes of electrodes during the charge–discharge process [233]. This poor contact eventually leads to the formation and propagation of cracks [234] as well as the delamination of interfaces [235,236]. Sulfide-based electrolytes possess good mechanical ductility, thus can maintain good contact with electrodes without the degradation of the interfacial contact resistance [237]. In contrast, oxide-based electrolytes suffer from the poor adhesion of interfaces with electrodes as most ceramics are vulnerable to cracking due to the low ductility [238,239]. The insufficient mechanical contact results in the delamination or “dead” area induced by isolated electrode contact points from solid electrolytes. Due to the lack of conduction paths, neither electrons nor Li

⁺ can be transferred across the dead areas, which in turn leads to the growth of interfacial resistance and capacity fading ^[103]. Furthermore, the large volume changes of electrode materials during repeated charge–discharge processes could also lead to the loss of effective contact between electrodes and solid electrolytes ^[104]. Zhang et al. ^[98] first demonstrated changes in the pressure and height of LCO/Li

can be transferred across the dead areas, which in turn leads to the growth of interfacial resistance and capacity fading [240]. Furthermore, the large volume changes of electrode materials during repeated charge–discharge processes could also lead to the loss of effective contact between electrodes and solid electrolytes [241]. Zhang et al. [233] first demonstrated changes in the pressure and height of LCO/Li

₁₀

GeP

₂

₁₂

/In and LCO/Li

₁₀

GeP

₂

₁₂

/LTO under galvanostatic cycling where the volume expansions of LCO, LTO and In were found to be 2%, 0.2% and 105.6%, respectively. Due to the significant volume change of In, the LCO/Li

₁₀

GeP

₂

₁₂/In cell showed severe capacity fading. Similarly, Koerver et al. ^[100] detected the increased interfacial resistance and capacity fading caused by the contact loss at the NCM-811/β-Li

/In cell showed severe capacity fading. Similarly, Koerver et al. [235] detected the increased interfacial resistance and capacity fading caused by the contact loss at the NCM-811/β-Li

₃

₄ interface.

interface.

The occurrence of the interfacial resistance by the formation of interlayers is a well-known phenomenon in SSBs. One of the main reasons for the interfacial resistance is the formation of space charge regions (SCRs). SCRs originate from the depletion of lithium near the interface between the cathode and the electrolyte in SSBs due to the high potential gradient ^[105]. The potential difference at this interface causes Li

The occurrence of the interfacial resistance by the formation of interlayers is a well-known phenomenon in SSBs. One of the main reasons for the interfacial resistance is the formation of space charge regions (SCRs). SCRs originate from the depletion of lithium near the interface between the cathode and the electrolyte in SSBs due to the high potential gradient [242]. The potential difference at this interface causes Li

⁺

to move toward a higher potential region, causing lithium depletion and increasing the ionic resistance at the interface. Sulfide-based electrolytes exhibit a weaker interaction with Li

⁺

and lower chemical potential of Li

⁺

compared with those of oxide cathodes, such as LCO. Thus, the Li

⁺

in sulfide-based electrolytes will migrate into the oxide cathode easily, resulting in the redistribution of Li

⁺ at the interface which forms lithium depletion layers, SCRs ^[106]. Unlike sulfide-based electrolytes, the influence of SCRs is smaller in oxide-based electrolytes because the chemical potential of Li

at the interface which forms lithium depletion layers, SCRs [243]. Unlike sulfide-based electrolytes, the influence of SCRs is smaller in oxide-based electrolytes because the chemical potential of Li

⁺ in oxide electrolytes is comparable with that in the cathode ^[107]. At the interface between LCO and Li

in oxide electrolytes is comparable with that in the cathode [244]. At the interface between LCO and Li

_1+x+y

_2−y

_3−x

₁₂, the thickness of SCRs in the sulfide-based electrolyte was thicker than 1 μm determined by measuring the electric potential profile with transmission electron microscopy (TEM) ^[108]. A similar SCR thickness was also reported in LiCoPO

, the thickness of SCRs in the sulfide-based electrolyte was thicker than 1 μm determined by measuring the electric potential profile with transmission electron microscopy (TEM) [245]. A similar SCR thickness was also reported in LiCoPO

₄

/Li

_1+x

_2−x

(PO

₄

)

₃ using Kelvin probe force microscopy (KPFM) ^[109]. On the contrary, the thickness estimated from the resistance (~10 Ω cm

using Kelvin probe force microscopy (KPFM) [246]. On the contrary, the thickness estimated from the resistance (~10 Ω cm

²) at the LiPON/LCO interface was found to be in the range of nanometers ^[110]. De Klerk et al. ^[111] also estimated the nanometer-thick SCRs based on the interfacial resistance (17 Ω cm

) at the LiPON/LCO interface was found to be in the range of nanometers [247]. De Klerk et al. [248] also estimated the nanometer-thick SCRs based on the interfacial resistance (17 Ω cm

) between the solid electrolytes, i.e., garnet and NASICON (LLZO and Li

_1.2

_0.2

_1.8

(PO

₄

)

₃

) and the cathode (LCO) or anode (graphite).

Interfacial chemical reactions derived from the interdiffusion between electrodes and solid electrolytes can also contribute to high interfacial resistance ^[112]. These interfacial reactions can form an interphase layer known as SEI at the electrode/electrolyte interface by consuming Li

Interfacial chemical reactions derived from the interdiffusion between electrodes and solid electrolytes can also contribute to high interfacial resistance [249]. These interfacial reactions can form an interphase layer known as SEI at the electrode/electrolyte interface by consuming Li

⁺ and electrons from electrodes. The electrical properties of the SEI layer play a role in determining how the reaction between electrolytes and electrodes continues ^{[113][114][115]}. This SEI layer continues to grow until it blocks the Li

and electrons from electrodes. The electrical properties of the SEI layer play a role in determining how the reaction between electrolytes and electrodes continues [250,251,252]. This SEI layer continues to grow until it blocks the Li

⁺ transport over the electrolyte/electrode. Park et al. ^[116] showed that an approximately 50-nm-thick layer forms in the vicinity of the LCO/Garnet interface due to the mutual diffusion of Co, La and Zr which leads to capacity fading. In addition, Wenzel et al. ^[117] also revealed that Li

transport over the electrolyte/electrode. Park et al. [253] showed that an approximately 50-nm-thick layer forms in the vicinity of the LCO/Garnet interface due to the mutual diffusion of Co, La and Zr which leads to capacity fading. In addition, Wenzel et al. [254] also revealed that Li

₃

P, Li

₂

S and Li–Ge alloys form a SEI layer upon the reaction of Li

₁₀

GeP

₂

₁₂ solid electrolyte with Li metal by in situ X-ray photoemission spectroscopy.

solid electrolyte with Li metal by in situ X-ray photoemission spectroscopy. As a general strategy to resolve the aforementioned issue at the electrode/electrolyte interface, nanometer-thick interfacial buffer layers have been grown to enhance the performance of the SSBs [255,256]. Consequently, it is critical to employ thin-film growth techniques that can provide high purity and desired crystallinity of target materials in SSBs’ assembly processes. Furthermore, the growth of thin films is a key success factor in building SSTFBs that have dramatically reduced charge-transfer resistance throughout the device. Therefore, understanding the precise control of thin-film growth and determining the impact of thin films on battery performances are requisite.

As a general strategy to resolve the aforementioned issue at the electrode/electrolyte interface, nanometer-thick interfacial buffer layers have been grown to enhance the performance of the SSBs ^[118][119]. Consequently, it is critical to employ thin-film growth techniques that can provide high purity and desired crystallinity of target materials in SSBs’ assembly processes. Furthermore, the growth of thin films is a key success factor in building SSTFBs that have dramatically reduced charge-transfer resistance throughout the device. Therefore, understanding the precise control of thin-film growth and determining the impact of thin films on battery performances are requisite.

4. Electrodes and Electrolytes for SSTFBs

To meet the increasing demand for portable (micro-)electronic applications in today’s information-rich and mobile society, developing rechargeable battery systems with high energy density and reduced dimensions is crucial. For such battery systems, SSTFBs are one of the most attractive battery systems owing to their shape, versatility, flexibility and lightness ^{[120][121][122]}. Since being first introduced in 1983 ^[123], SSTFBs have been continuously studied over the past four decades ^{[122][124][125][126][127][128][129]}. In recent years, considerable progress has been made in the development of SSTFBs along with advances in thin-film technologies ^[130][131]. SSTFBs provide unique advantages such as outstanding cycle life and safety compared to conventional LIBs ^[132][133]. Moreover, SSTFBs enable the miniaturization of LIBs required for applications, including implantable medical devices, wireless microsensors, microelectromechanical system devices and flexible electronics ^[134][135].

To meet the increasing demand for portable (micro-)electronic applications in today’s information-rich and mobile society, developing rechargeable battery systems with high energy density and reduced dimensions is crucial. For such battery systems, SSTFBs are one of the most attractive battery systems owing to their shape, versatility, flexibility and lightness [315,316,317]. Since being first introduced in 1983 [318], SSTFBs have been continuously studied over the past four decades [317,319,320,321,322,323,324]. In recent years, considerable progress has been made in the development of SSTFBs along with advances in thin-film technologies [325,326]. SSTFBs provide unique advantages such as outstanding cycle life and safety compared to conventional LIBs [327,328]. Moreover, SSTFBs enable the miniaturization of LIBs [317,323,324] required for applications, including implantable medical devices, wireless microsensors, microelectromechanical system devices and flexible electronics [318,329,330].

SSTFBs are composed of multiple micron-sized electrochemical cells consisting of a cathode and an anode electrode separated by an electrolyte. A thin-film electrochemical cell is generally fabricated on a solid substrate like glass, ceramic or even polymer. The first layer is usually a current collector, then followed by the electrode, electrolyte, electrode and another layer of a current collector. Generally, the thickness of thin films in SSTFBs is in the range of nanometers to microns. Such thin layers can significantly enhance the charge transfer kinetics ^[136] which prevents the local overcharging and discharging issue reported in conventional battery systems ^[136]. In addition, SSTFBs use dense thin films without a polymeric binder and thus can be used as an ideal system for the fundamental understanding of energy storage mechanisms. Furthermore, SSTFBs have higher volumetric and gravimetric power density (

SSTFBs are composed of multiple micron-sized electrochemical cells consisting of a cathode and an anode electrode separated by an electrolyte. A thin-film electrochemical cell is generally fabricated on a solid substrate like glass, ceramic or even polymer. The first layer is usually a current collector, then followed by the electrode, electrolyte, electrode and another layer of a current collector [317]. Generally, the thickness of thin films in SSTFBs is in the range of nanometers to microns. Such thin layers can significantly enhance the charge transfer kinetics [59,331] which prevents the local overcharging and discharging issue reported in conventional battery systems [317,331]. In addition, SSTFBs use dense thin films without a polymeric binder and thus can be used as an ideal system for the fundamental understanding of energy storage mechanisms. Furthermore, SSTFBs have higher volumetric and gravimetric power density (

Figure 2) compared to other battery systems ^[137]. The use of thin-film electrochemical cells is therefore a promising and practical strategy to fully utilize the advantage of lithium-based batteries for diverse applications.

11) compared to other battery systems [332]. The use of thin-film electrochemical cells is therefore a promising and practical strategy to fully utilize the advantage of lithium-based batteries for diverse applications.

Figure 211. Comparison of the volumetric and gravimetric energy density of solid-state thin-film batteries (SSTFBs) with other batteries ^{[138][139][140]}

Comparison of the volumetric and gravimetric energy density of solid-state thin-film batteries (SSTFBs) with other batteries [333,334,335]

5. Conclusions

Replacing liquid electrolytes with solid counterparts allows SSBs to exhibit excellent safety, electrochemical stability and high energy density. Despite these advantages, further enhancement of the current SSBs is required to be used in practical applications. Improving the material properties of electrodes and electrolytes may accelerate the development of the next-generation energy storage systems. This review discussed key advances in battery materials and possible solutions to solve their issues. Surface modification, doping and nanostructuring have been successfully used to improve the electrode performance. For the solid electrolyte, many efforts have been devoted to improving the ionic conductivity by doping or altering the crystal structures. Indeed, several studies have improved the thermal and chemical stability of the solid electrolytes by replacing sensitive elements, such as transition metals. While we mainly focused on oxide-based solid electrolytes, LiRAP and sulfide-based solid electrolytes are becoming increasingly attractive owing to their outstanding ionic conductivity. However, the highly air sensitive nature of these electrolytes remains a substantial obstacle.

Over the last few decades, the development of oxide thin films has led to many technological breakthroughs for energy and electronic devices. In particular, 2D planar heterostructures have been prevailingly investigated as they lead not only to improved functionalities but even to the occurrence of novel properties that do not belong to the bulk ^[141][142]. For instance, the discovery of the formation of a conducting interface between two insulators ^[142], STO and LaAlO

Over the last few decades, the development of oxide thin films has led to many technological breakthroughs for energy and electronic devices. In particular, 2D planar heterostructures have been prevailingly investigated as they lead not only to improved functionalities but even to the occurrence of novel properties that do not belong to the bulk [438,439]. For instance, the discovery of the formation of a conducting interface between two insulators [438], STO and LaAlO

₃ (LAO), brought the breakthrough in the field of oxide electronics while also becoming the pole of attraction and inspiration for numerous studies ^[143][144]. Recently, a couple of attempts have been made to utilize heterostructure thin films in lithium-based batteries ^{[145][146][147]}. In addition, developing new forms of materials with tailored properties could bring technological breakthroughs in the next-generation energy storage systems. For example, 3D nanostructures can offer an extremely large number of interfaces and surface area, which are beneficial for enhancing the electrochemical performance and ion transport in materials ^[148][149]. To date, a few studies have been investigated the influence of 3D nanostructures on the performance of lithium-based batteries ^[150][151]. Exploring new forms of materials will bring new opportunities to develop high-performance electrodes and electrolytes for SSBs and SSTFBs

(LAO), brought the breakthrough in the field of oxide electronics while also becoming the pole of attraction and inspiration for numerous studies [440,441]. Recently, a couple of attempts have been made to utilize heterostructure thin films in lithium-based batteries [395,442,443,444]. In addition, developing new forms of materials with tailored properties could bring technological breakthroughs in the next-generation energy storage systems. For example, 3D nanostructures can offer an extremely large number of interfaces and surface area, which are beneficial for enhancing the electrochemical performance and ion transport in materials [445,446]. To date, a few studies have been investigated the influence of 3D nanostructures on the performance of lithium-based batteries [447,448]. Exploring new forms of materials will bring new opportunities to develop high-performance electrodes and electrolytes for SSBs and SSTFBs